Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR System) › from 2019.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0309414 ECD SYSTEM(w/o EGR System) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR System)  P0180  Fuel Temperature Sensor "A" Circuit  P0182  Fuel Temperature Sensor "A" Circuit Low Input  P0183  Fuel Temperature Sensor "A" Circuit High Input  


DESCRIPTION

The fuel temperature sensor monitors the fuel temperature. The fuel temperature sensor has a thermistor that varies its resistance depending on the fuel temperature. When the fuel temperature is low, the resistance of the thermistor is high. When the temperature is high, the resistance is low. The variations of resistance are communicated to the ECM as changes of voltage (see Fig. 1).

The fuel temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the fuel temperature sensor from terminal THF via resistor R.

The resistor R and fuel temperature sensor are connected in series. When the resistance value of the fuel temperature sensor changes due to a change of fuel temperature, the voltage at terminal THF also changes. Based on this signal, the ECM corrects the pressure control compensation of the fuel supply pump assembly and determines if there are errors.

A208462E01
1.469,2 1.625,1.76 1.625,1.76 1.771,1.76 false 0.208,0.146 0.906,0.49 0.698,0.344 10 false (Fig. 1) 0.208,0.542 1.313,0.823 1.104,0.281 10 false Resistance kΩ 1.823,1.688 2.656,2.031 0.833,0.344 10 false Acceptable 1.208,4.073 2.521,4.385 1.313,0.313 10 false Temperature °C (°F)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0180 Fuel Temperature Sensor "A" Circuit Open or short in fuel temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open or short in fuel temperature sensor circuit

·

Fuel temperature sensor

·

Fuel temperature sensor, suction control valve wire

·

ECM


Comes on DTC stored
P0182 Fuel Temperature Sensor "A" Circuit Low Input Short in fuel temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Short in fuel temperature sensor circuit

·

Fuel temperature sensor

·

Fuel temperature sensor, suction control valve wire

·

ECM


Comes on DTC stored
P0183 Fuel Temperature Sensor "A" Circuit High Input Open in fuel temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open in fuel temperature sensor circuit

·

Fuel temperature sensor

·

Fuel temperature sensor, suction control valve wire

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0180
P0182
P0183
Ignition switch ON for 0.5 seconds

WIRING DIAGRAM

A184084E13
2.063,1.01 2.375,1.177 0.313,0.167 10 false THF 2.458,1 2.635,1.177 0.177,0.177 10 false 2 2.135,1.615 2.375,1.781 0.24,0.167 10 false E2 5.563,1.01 5.875,1.177 0.313,0.167 10 false THF 6.25,0.542 6.563,0.708 0.313,0.167 10 false 5 V 5.563,1.625 5.802,1.792 0.24,0.167 10 false E2 6.177,0.865 6.333,1.031 0.156,0.167 10 false R 2.479,1.604 2.656,1.781 0.177,0.177 10 false 1 5.219,1.01 5.5,1.188 0.281,0.177 10 false 116 5.906,2.677 6.354,2.885 0.448,0.208 10 false C39 5.917,2.865 6.333,3.042 0.417,0.177 10 false ECM 5.25,1.625 5.427,1.802 0.177,0.177 10 false 75 0.708,2.531 2.375,2.719 1.667,0.188 10 false Fuel Temperature Sensor 3.875,2.688 4.198,2.844 0.323,0.156 10 false rC1 0.708,2.313 1.156,2.521 0.448,0.208 10 false r3

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See pageEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION) and initialization (See pageEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>INITIALIZATION).


HINT:
·

If DTCs relating to different systems are output, and they share terminal E2 as their ground, check this ground circuit first.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (FUEL TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.

Powertrain > Engine and ECT > Data List
Tester Display
Fuel Temperature
50003 61 403

d.

Read the value.

Standard value:

Same value as the actual fuel temperature


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
OK (Same as actual fuel temperature) C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or more.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

5.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A311463C04
1.531,2.885 1.948,3.167 0.417,0.281 1.177,4.365 1.552,4.031 true 2.25,4.385 1.917,4.031 true 0.625,1.729 0.938,1.885 0.313,0.156 10 false *1 2.646,1.906 2.958,2.063 0.313,0.156 10 false *2 0.229,2.677 0.542,2.833 0.313,0.156 10 false *a 2.375,1.031 2.688,1.188 0.313,0.156 10 false THF 1.094,4.396 1.406,4.552 0.313,0.156 10 false E2 2.208,4.406 2.521,4.563 0.313,0.156 10 false THF 2.375,1.406 2.688,1.563 0.313,0.156 10 false E2 1.656,2.938 1.948,3.115 0.292,0.177 10 false rC1
*1 Fuel Temperature Sensor, Suction Control Valve
*2 ECM
*a Front view of wire harness connector
(to Fuel Temperature Sensor, Suction Control Valve)


Disconnect the fuel temperature sensor, suction control valve connector.


b.

Connect terminals 2 (THF) and 1 (E2) of the fuel temperature sensor, suction control valve wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT /Data List / Fuel Temperature.

Powertrain > Engine and ECT > Data List
Tester Display
Fuel Temperature
50003 61 403

f.

Read the value.

Standard value:

140°C (284°F) or higher



Result:
Proceed to
OK
NG



OK

3.CHECK FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE WIRE

NG

4.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE CONNECTOR - ECM)
3.CHECK FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE WIRE
a.
A311464C03
0.521,0.792 0.875,1.021 0.354,0.229 1,3.573 1.354,3.802 0.354,0.229 1.49,4.281 1.76,3.854 true 2.396,4.302 2.052,3.854 true 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a 0.635,0.823 0.948,0.979 0.313,0.156 10 false r3 1.083,3.604 1.396,3.76 0.313,0.156 10 false rC1 1.344,4.323 1.802,4.479 0.458,0.156 10 false THF 2.365,4.323 2.698,4.479 0.333,0.156 10 false E2
*a Component without harness connected
(Fuel Temperature Sensor, Suction Control Valve Wire)


Remove the fuel temperature sensor, suction control valve wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r3-1 - rC1-4 (E2) Always Below 1 Ω
r3-2 - rC1-3 (THF) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE FUEL TEMPERATURE SENSOR

NG

REPAIR OR REPLACE FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE WIRE

4.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE CONNECTOR - ECM)
a.
A311457C08
1.531,0.417 1.948,0.667 0.417,0.25 1.25,2.333 1.667,2.583 0.417,0.25 1.26,1.854 1.563,1.583 true 2.229,1.865 1.948,1.583 false 2.281,4.177 1.448,3.521 true 0.802,4.167 1,3.698 true 0.167,0.104 0.479,0.26 0.313,0.156 10 false *a 0.167,2.135 0.479,2.292 0.313,0.156 10 false *b 1.646,0.458 1.906,0.677 0.26,0.219 10 false rC1 1.333,2.375 1.646,2.531 0.313,0.156 10 false C39 1.167,1.885 1.479,2.042 0.313,0.156 10 false E2 2.146,1.875 2.458,2.031 0.313,0.156 10 false THF 0.542,4.26 1.219,4.448 0.677,0.188 10 false 116 (THF) 2.208,4.26 2.979,4.438 0.771,0.177 10 false 75 (E2)
*a Front view of wire harness connector
(to Fuel Temperature Sensor, Suction Control Valve)
*b Front view of wire harness connector
(to ECM)


Disconnect the fuel temperature sensor, suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
rC1-3 (THF) - C39-116 (THF) Always Below 1 Ω
rC1-4 (E2) - C39-75 (E2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A166688C03
0.583,2.083 0.823,2.281 0.24,0.198 10 false *1 2.667,2.302 2.906,2.5 0.24,0.198 10 false *2 2.396,1.427 2.823,1.615 0.427,0.188 10 false THF 2.406,1.906 2.833,2.094 0.427,0.188 10 false E2
*1 Fuel Temperature Sensor, Suction Control Valve
*2 ECM


Disconnect the fuel temperature sensor, suction control valve connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.

Powertrain > Engine and ECT > Data List
Tester Display
Fuel Temperature
50003 61 403

e.

Read the value.

Standard value:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

6.CHECK FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE WIRE

NG

7.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE CONNECTOR - ECM)
6.CHECK FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE WIRE
a.
A311464C03
0.521,0.792 0.875,1.021 0.354,0.229 1,3.573 1.354,3.802 0.354,0.229 1.49,4.281 1.76,3.854 true 2.396,4.302 2.052,3.854 true 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a 0.635,0.823 0.948,0.979 0.313,0.156 10 false r3 1.083,3.604 1.396,3.76 0.313,0.156 10 false rC1 1.344,4.323 1.802,4.479 0.458,0.156 10 false THF 2.365,4.323 2.698,4.479 0.333,0.156 10 false E2
*a Component without harness connected
(Fuel Temperature Sensor, Suction Control Valve Wire)
*b Fuel Temperature Sensor Wire "A"
*c Fuel Temperature Sensor, Suction Control Valve Wire "B"


Remove the fuel temperature sensor, suction control valve wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r3-2 or rC1-3 (THF) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE WIRE

7.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR, SUCTION CONTROL VALVE CONNECTOR - ECM)
a.
A311457C08
1.531,0.417 1.948,0.667 0.417,0.25 1.25,2.333 1.667,2.583 0.417,0.25 1.26,1.854 1.563,1.583 true 2.229,1.865 1.948,1.583 false 2.281,4.177 1.448,3.521 true 0.802,4.167 1,3.698 true 0.167,0.104 0.479,0.26 0.313,0.156 10 false *a 0.167,2.135 0.479,2.292 0.313,0.156 10 false *b 1.646,0.458 1.906,0.677 0.26,0.219 10 false rC1 1.333,2.375 1.646,2.531 0.313,0.156 10 false C39 1.167,1.885 1.479,2.042 0.313,0.156 10 false E2 2.146,1.875 2.458,2.031 0.313,0.156 10 false THF 0.542,4.26 1.219,4.448 0.677,0.188 10 false 116 (THF) 2.208,4.26 2.979,4.438 0.771,0.177 10 false 75 (E2)
*a Front view of wire harness connector
(to Fuel Temperature Sensor, Suction Control Valve)
*b Front view of wire harness connector
(to ECM)


Disconnect the fuel temperature sensor, suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
rC1-3 (THF) or C39-116 (THF) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR