Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR System) › from 2019.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0309414 ECD SYSTEM(w/o EGR System) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR System)  P2121  Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance  


DESCRIPTION

Refer to DTC P2120.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>P2120

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance The difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V for 0.5 seconds
(1 trip detection logic)
·

Accelerator pedal position sensor circuit

·

Accelerator pedal sensor assembly

·

ECM


Comes on DTC stored

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION)
a.

Connect the GTS to the DLC3.


b.
C129061C23
0.698,1.635 1.448,1.844 0.75,0.208 10 false *a 0.292,0.115 1.625,0.323 1.333,0.208 10 false *1 2.26,1.615 2.927,1.823 0.667,0.208 10 false *b
*1 Accelerator Pedal
*a Depressed
*b Released


Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.

Powertrain > Engine and ECT > Data List
Tester Display
Accel Sens. No.1 Volt %
Accel Sens. No.2 Volt %
50003 61 75,76

d.

Read the values.

Standard Voltage:
Accelerator Pedal Accel Sens. No.1 Volt % Accel Sens. No.2 Volt %
Released 10 to 22% 24 to 40%
Depressed 52 to 90% 68 to 99%



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR POSITION SENSOR ASSEMBLY - ECM)
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR POSITION SENSOR ASSEMBLY - ECM)
a.
A311474C05
1.563,2.479 2.01,2.75 0.448,0.271 1.49,0.219 1.938,0.49 0.448,0.271 0.688,1.281 1.354,1.125 true 1.365,1.688 1.667,1.146 true 0.896,1.51 1.542,1.146 true 1.844,1.688 1.792,1.135 true 1.917,1.156 2.219,1.531 true 2.063,1.135 2.563,1.406 true 1.823,3.781 0.646,3.615 true 1.917,3.781 0.802,4.125 true 2.01,3.781 1.125,4.302 true 2.083,3.781 1.583,4.375 true 2.26,3.781 2.625,4.094 true 2.188,3.781 2.125,4.208 true 0.177,0.167 0.49,0.365 0.313,0.198 10 false *a 0.177,2.448 0.49,2.646 0.313,0.198 10 false *b 1.708,2.531 2.031,2.719 0.323,0.188 10 false I84 1.615,0.281 1.865,0.448 0.25,0.167 10 false I43 0.271,1.219 0.885,1.417 0.615,0.198 10 false VCP2 0.615,1.521 1.229,1.719 0.615,0.198 10 false EPA2 1.208,1.719 1.823,1.917 0.615,0.198 10 false VPA2 1.781,1.729 2.396,1.927 0.615,0.198 10 false VCPA 2.24,1.563 2.854,1.76 0.615,0.198 10 false EPA 2.625,1.406 3.24,1.604 0.615,0.198 10 false VPA 0.104,4.073 1.031,4.344 0.927,0.271 10 false 54 (VPA2) 0.063,3.51 0.74,3.802 0.677,0.292 10 false 53 (VPA) 0.698,4.323 1.792,4.583 1.094,0.26 10 false 55 (VCPA) 1.448,4.406 2.823,4.604 1.375,0.198 10 false 56 (VCP2) 1.938,4.24 3.313,4.438 1.375,0.198 10 false 57 (EPA) 2.5,4.115 3.323,4.344 0.823,0.229 10 false 58 (EPA2)
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)
*b Front view of wire harness connector
(to ECM)


Disconnect the accelerator pedal sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I43-1 (VCP2) - I84-56 (VCP2) Always Below 1 Ω
I43-2 (EPA2) - I84-58 (EPA2) Always Below 1 Ω
I43-3 (VPA2) - I84-54 (VPA2) Always Below 1 Ω
I43-4 (VCPA) - I84-55 (VCPA) Always Below 1 Ω
I43-5 (EPA) - I84-57 (EPA) Always Below 1 Ω
I43-6 (VPA) - I84-53 (VPA) Always Below 1 Ω
I43-1 (VCP2) or I84-56 (VCP2) - Body ground Always 10 kΩ or higher
I43-2 (EPA2) or I84-58 (EPA2) - Body ground Always 10 kΩ or higher
I43-3 (VPA2) or I84-54 (VPA2) - Body ground Always 10 kΩ or higher
I43-4 (VCPA) or I84-55 (VCPA) - Body ground Always 10 kΩ or higher
I43-5 (EPA) or I84-57 (EPA) - Body ground Always 10 kΩ or higher
I43-6 (VPA) or I84-53 (VPA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Clear.

Powertrain > Engine and ECT > Clear DTCs
50002 61

d.

Clear the DTC.


e.

Start the engine.


f.

Allow the engine to idle for 15 seconds.


g.

Depress and release the accelerator pedal several times.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

i.

Read the DTC.

Result:
Result Proceed to
P2121 is output A
No DTC is output B




A

5.REPLACE ECM

B

END

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON.


e.

Fully release the accelerator pedal for 3 seconds or more, then depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.


f.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED