Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o EGR System) › from 2019.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0309414 ECD SYSTEM(w/o EGR System) J

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR System)  Injector Circuit  


DESCRIPTION

The injector driver drives the injectors at high speeds with a high-voltage DC/DC converter. The ECM constantly monitors the injector driver and stops the engine if an abnormal condition is detected.

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK EDU (POWER SOURCE)
a.
A130531C04
0.25,0.823 0.688,1.083 0.438,0.26 0.25,1.125 0.688,1.385 0.438,0.26 0.25,2.625 0.688,2.885 0.438,0.26 0.25,2.938 0.688,3.198 0.438,0.26 1.042,1.583 0.854,1.833 true 2.333,3.448 2.521,3.719 true 0.344,0.875 0.656,1.042 0.313,0.167 10 false C54 0.719,0.76 0.896,0.906 0.177,0.146 10 false *1 0.354,1.177 0.656,1.333 0.302,0.156 10 false C52 0.719,1.063 0.896,1.208 0.177,0.146 10 false *2 0.354,2.677 0.656,2.844 0.302,0.167 10 false C55 0.708,2.563 0.885,2.708 0.177,0.146 10 false *1 0.365,2.99 0.667,3.156 0.302,0.167 10 false C53 0.708,2.875 0.885,3.021 0.177,0.146 10 false *2 0.667,1.844 1.042,2.073 0.375,0.229 10 false GND 2.448,3.74 2.823,3.969 0.375,0.229 10 false +B 0.198,0.208 2.583,0.563 2.385,0.354 10 false *a
*1 No. 1
*2 No. 2
*a Front view of wire harness connector
(to EDU)


Disconnect the No. 1 injector driver (EDU) connectors.


b.

Disconnect the No. 2 injector driver (EDU) connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage (No. 1):
Tester Connection Switch Condition Specified Condition
C55-8 (+B) - C54-1 (GND) Ignition switch ON 11 to 14 V


Standard Voltage (No. 2):
Tester Connection Switch Condition Specified Condition
C53-8 (+B) - C52-1 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE INJECTOR DRIVER (NO. 1 OR NO. 2)

NG

2.INSPECT EDU RELAY (EDU 1 OR EDU 2)
2.INSPECT EDU RELAY (EDU 1 OR EDU 2)
a.

Inspect the EDU relay (EDU 1 or EDU 2).

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT MAIN RELAY (MAIN OR MAIN 2)

NG

REPLACE EDU RELAY (EDU 1 OR EDU 2)

3.INSPECT MAIN RELAY (MAIN OR MAIN 2)

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (EDU RELAY - MAIN RELAY, MAIN RELAY - BATTERY)

NG

REPLACE MAIN RELAY (MAIN OR MAIN 2)

4.CHECK HARNESS AND CONNECTOR (EDU RELAY - MAIN RELAY, MAIN RELAY - BATTERY)
a.

Remove the EDU1 relay from the engine room relay block assembly.


b.

Remove the MAIN relay from the engine room relay block assembly.


c.

Disconnect the cable from the negative (-) battery terminal.


d.

Disconnect the cable from the positive (+) battery terminal.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (No. 1):
Tester Connection Condition Specified Condition
EDU1 relay terminal 3 - MAIN relay terminal 3 Always Below 1 Ω
MAIN relay terminal 5 - Battery positive (+) terminal Always Below 1 Ω
EDU1 relay terminal 3 or MAIN relay terminal 3 - Body ground Always 10 kΩ or higher
MAIN relay terminal 5 - Body ground Always 10 kΩ or higher



f.

Remove the EDU2 relay from the engine room relay block assembly.


g.

Remove the MAIN2 relay from the engine room relay block assembly.


h.

Disconnect the cable from the negative (-) battery terminal.


i.

Disconnect the cable from the positive (+) battery terminal.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (No. 2):
Tester Connection Condition Specified Condition
EDU2 relay terminal 3 - MAIN2 relay terminal 3 Always Below 1 Ω
MAIN2 relay terminal 5 - Battery positive (+) terminal Always Below 1 Ω
EDU2 relay terminal 3 or MAIN2 relay terminal 3 - Body ground Always 10 kΩ or higher
MAIN2 relay terminal 5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (EDU RELAY - EDU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (EDU RELAY - EDU)
a.

Remove the EDU1 or EDU2 relay from the engine room relay block assembly.


b.

Remove the EDU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (No. 1):
Tester Connection Condition Specified Condition
C55-8 (+B) - EDU1 relay terminal 5 Always Below 1 Ω
C55-8 (+B) or EDU1 relay terminal 5 - Body ground Always 10 kΩ or higher


Standard Resistance (No. 2):
Tester Connection Condition Specified Condition
C53-8 (+B) - EDU2 relay terminal 5 Always Below 1 Ω
C53-8 (+B) or EDU2 relay terminal 5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (EDU RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (EDU RELAY - ECM)
a.

Remove the EDU1 or EDU2 relay from the engine room relay block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (No. 1):
Tester Connection Condition Specified Condition
I84-45 (IREL) - EDU1 relay terminal 2 Always Below 1 Ω
I84-45 (IREL) or EDU1 relay terminal 2 - Body ground Always 10 kΩ or higher


Standard Resistance (No. 2):
Tester Connection Condition Specified Condition
I84-46 (IRL2) - EDU2 relay terminal 2 Always Below 1 Ω
I84-46 (IRL2) or EDU2 relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (EDU RELAY - MAIN RELAY, MAIN RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (EDU RELAY - MAIN RELAY, MAIN RELAY - BODY GROUND)
a.

Remove the EDU1 relay from the engine room relay block assembly.


b.

Remove the MAIN relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (No. 1):
Tester Connection Condition Specified Condition
EDU1 relay terminal 1 - MAIN relay terminal 3 Always Below 1 Ω
EDU1 relay terminal 1 or MAIN relay terminal 3 - Body ground Always 10 kΩ or higher



d.

Remove the EDU2 relay from the engine room relay block assembly.


e.

Remove the MAIN2 relay from the engine room relay block assembly.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (No. 2):
Tester Connection Condition Specified Condition
EDU2 relay terminal 1 - MAIN2 relay terminal 3 Always Below 1 Ω
EDU2 relay terminal 1 or MAIN2 relay terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (EDU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (EDU - BODY GROUND)
a.

Disconnect the EDU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (No. 1):
Tester Connection Condition Specified Condition
C54-1 (GND) - Body ground Always Below 1 Ω


Standard Resistance (No. 2):
Tester Connection Condition Specified Condition
C52-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EDU - BODY GROUND)