The EDU drives the injectors at high speeds. The EDU delivers high-speed drive signals under high-pressure fuel conditions using the DC/DC converter, which provides a high-voltage and quick-charging system.
Soon after the EDU receives an injection command (#1 to #8) signal from the ECM, the EDU responds to the command with an injector injection confirmation (INJF) signal when the current is applied to the injector.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P062D | Fuel Injector Driver Circuit Performance Bank1 | Open or short in No. 1 injector driver (EDU) or injector circuit (1 trip detection logic) |
·
Open or short in No. 1 injector driver (EDU) circuit
·
Fuel Injector
·
No. 1 EDU
·
ECM |
Comes on | DTC stored |
| P062E | Fuel Injector Driver Circuit Performance Bank2 | Open or short in No. 2 injector driver (EDU) or injector circuit (1 trip detection logic) |
·
Open or short in No. 2 injector driver (EDU) circuit
·
Fuel Injector
·
No. 2 EDU
·
ECM |
Comes on | DTC stored |
DTC P062D or P062E is detected when starting the engine and letting it idle for 30 seconds.
The ECM continuously monitors both injection command (#1 to #8) signals and injection confirmation (INJF) signals. This DTC will be set if the ECM determines that the number of #1 to #8 signals and INJF signals are inconsistent.
The injectors are grounded over a Field Effect Transistor (FET) and a serial resistor. This resistor creates a voltage drop, which is monitored by the EDU (injector drive circuit), in relation to the current drawn by the injector. When the injector current becomes too high, the voltage drop over the resistor exceeds a specified level and no INJF signal for that cylinder is sent to the ECM.
After the engine is started, when there is no injection confirmation (INJF) signal from the No. 1 or No. 2 EDU to the ECM even though the ECM sends injection command (#1 to #8) signals to the No. 1 or No. 2 EDU, DTC P062D or DTC P062E is output.
If this DTC is set, the ECM enters fail-safe mode and limits engine power or stops the engine. The fail-safe mode continues until the ignition switch is turned off.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>INITIALIZATION).
After replacing an injector, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>REGISTRATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| *1 | No. 1 |
| *2 | No. 2 |
| *a | Front view of wire harness connector (to EDU) |
Disconnect the No. 1 injector driver (EDU) connectors.
Disconnect the No. 2 injector driver (EDU) connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C55-8 (+B) - C54-1 (GND) | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C53-8 (+B) - C52-1 (GND) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector (to Fuel Injector) |
| *b | Front view of wire harness connector (to No. 1 EDU) |
Disconnect the fuel injector connectors.
Disconnect the No. 1 EDU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C48-2 - C55-4 (INJ1) | Always | Below 1 Ω |
| C72-2 - C55-3 (INJ4) | Always | Below 1 Ω |
| C64-2 - C55-2 (INJ6) | Always | Below 1 Ω |
| C57-2 - C55-1 (INJ7) | Always | Below 1 Ω |
| C48-1 - C55-5 (COM1) | Always | Below 1 Ω |
| C72-1 - C55-5 (COM1) | Always | Below 1 Ω |
| C64-1 - C55-6 (COM2) | Always | Below 1 Ω |
| C57-1 - C55-6 (COM2) | Always | Below 1 Ω |
| C48-2 or C55-4 (INJ1) - Body ground | Always | 10 kΩ or higher |
| C72-2 or C55-3 (INJ4) - Body ground | Always | 10 kΩ or higher |
| C64-2 or C55-2 (INJ6) - Body ground | Always | 10 kΩ or higher |
| C57-2 or C55-1 (INJ7) - Body ground | Always | 10 kΩ or higher |
| C48-1 or C55-5 (COM1) - Body ground | Always | 10 kΩ or higher |
| C72-1 or C55-5 (COM1) - Body ground | Always | 10 kΩ or higher |
| C64-1 or C55-6 (COM2) - Body ground | Always | 10 kΩ or higher |
| C57-1 or C55-6 (COM2) - Body ground | Always | 10 kΩ or higher |
| *a | Front view of wire harness connector (to Fuel Injector) |
| *b | Front view of wire harness connector (to No. 2 EDU) |
Disconnect the C67, C51, C49 and C63 fuel injector connectors.
Disconnect the C53 No. 2 EDU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C67-2 - C53-4 (INJ2) | Always | Below 1 Ω |
| C51-2 - C53-3 (INJ5) | Always | Below 1 Ω |
| C49-2 - C53-1 (INJ3) | Always | Below 1 Ω |
| C63-2 - C53-2 (INJ8) | Always | Below 1 Ω |
| C67-1 - C53-5 (COM4) | Always | Below 1 Ω |
| C51-1 - C53-5 (COM4) | Always | Below 1 Ω |
| C49-1 - C53-6 (COM5) | Always | Below 1 Ω |
| C63-1 - C53-6 (COM5) | Always | Below 1 Ω |
| C67-2 or C53-4 (INJ2) - Body ground | Always | 10 kΩ or higher |
| C51-2 or C53-3 (INJ5) - Body ground | Always | 10 kΩ or higher |
| C49-2 or C53-1 (INJ3) - Body ground | Always | 10 kΩ or higher |
| C63-2 or C53-2 (INJ8) - Body ground | Always | 10 kΩ or higher |
| C67-1 or C53-5 (COM4) - Body ground | Always | 10 kΩ or higher |
| C51-1 or C53-5 (COM4) - Body ground | Always | 10 kΩ or higher |
| C49-1 or C53-6 (COM5) - Body ground | Always | 10 kΩ or higher |
| C63-1 or C53-6 (COM5) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector (to No. 1 EDU) |
| *b | Front view of wire harness connector (to ECM) |
Disconnect the No. 1 EDU connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C54-6 (#10) - C39-40 (#1) | Always | Below 1 Ω |
| C54-5 (#40) - C39-37 (#4) | Always | Below 1 Ω |
| C54-3 (#60) - C39-35 (#6) | Always | Below 1 Ω |
| C54-2 (#70) - C39-34 (#7) | Always | Below 1 Ω |
| C54-7 (INJF) - C39-61 (INJF) | Always | Below 1 Ω |
| C54-6 (#10) or C39-40 (#1) - Body ground | Always | 10 kΩ or higher |
| C54-5 (#40) or C39-37 (#4) - Body ground | Always | 10 kΩ or higher |
| C54-3 (#60) or C39-35 (#6) - Body ground | Always | 10 kΩ or higher |
| C54-2 (#70) or C39-34 (#7) - Body ground | Always | 10 kΩ or higher |
| C54-7 (INJF) or C39-61 (INJF) - Body ground | Always | 10 kΩ or higher |
| *a | Front view of wire harness connector (to No. 2 EDU) |
| *b | Front view of wire harness connector (to ECM) |
Disconnect the No. 2 EDU connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C52-6 (#20) - C39-39 (#2) | Always | Below 1 Ω |
| C52-2 (#30) - C39-38 (#3) | Always | Below 1 Ω |
| C52-5 (#50) - C39-36 (#5) | Always | Below 1 Ω |
| C52-3 (#80) - C39-33 (#8) | Always | Below 1 Ω |
| C52-7 (INF2) - C39-60 (INF2) | Always | Below 1 Ω |
| C52-6 (#20) or C39-39 (#2) - Body ground | Always | 10 kΩ or higher |
| C52-2 (#30) or C39-38 (#3) - Body ground | Always | 10 kΩ or higher |
| C52-5 (#50) or C39-36 (#5) - Body ground | Always | 10 kΩ or higher |
| C52-3 (#80) or C39-33 (#8) - Body ground | Always | 10 kΩ or higher |
| C52-7 (INF2) or C39-60 (INF2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected (Fuel Injector) |
Disconnect the fuel injector connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 0.85 to 1.05 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 |
| *2 | No. 2 |
Interchange the No. 1 and No. 2 EDU connectors.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear DTCs.
Before deleting the DTCs, write them down.
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs do not change | A |
| DTCs change (change in malfunctioning cylinder or EDU code) | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off.
Start the engine and idle it for 10 seconds.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the injector driver.
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>INJECTOR DRIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the fuel injector assembly.
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/o DPF)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Go to the injector circuit.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>Injector Circuit
| Proceed to |
|---|
| NEXT |
NEXT