Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2021.07–2022.09
RM25T0E _53 Suspension _062777 TIRE PRESSURE MONITORING _0306275 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2174/74  Vehicle Speed Signal Malfunction  C2191/91  Vehicle Speed Signal Error (Test Mode DTC)  


DESCRIPTION

Speeds signals are sent from the combination meter assembly to the tire pressure warning ECU and receiver.

DTC C2191/91 is stored only during the signal check.

DTC No. Detection Item DTC Detection Condition Trouble Area
C2174/74 Vehicle Speed Signal Malfunction All conditions below are met:
·

DTC C2121/21, C2122/22, C2123/23, C2124/24 and/or C2125/25 is output

·

Vehicle speed signal malfunction


·

Combination meter assembly

·

Vehicle speed signal circuit

·

Wire harness or connector

·

Tire pressure warning ECU and receiver

·

Tire pressure warning valve and transmitter


C2191/91 Vehicle Speed Signal Error (Test Mode DTC) Test mode procedure is performed.
·

Meter / gauge system (speed signal)

·

Vehicle speed signal circuit

·

Wire harness or connector

·

Tire pressure warning ECU and receiver



WIRING DIAGRAM

C370427E03
1.135,0.552 1.448,0.75 0.313,0.198 10 false +S 1.125,1.365 1.438,1.563 0.313,0.198 10 false SI 2.979,1.375 3.292,1.573 0.313,0.198 10 false SP1 5.771,0.552 6.083,0.75 0.313,0.198 10 false SPD 0.135,1.823 0.448,2.021 0.313,0.198 10 false L25 0.156,1.99 1.99,2.208 1.833,0.219 10 false Combination Meter Assembly 1.469,0.406 1.781,0.604 0.313,0.198 10 false 8 1.448,1.229 1.76,1.427 0.313,0.198 10 false 9 2.667,1.25 2.979,1.448 0.313,0.198 10 false 14 2.635,1.885 2.948,2.083 0.313,0.198 10 false A42 4.479,1.271 5.823,1.49 1.344,0.219 10 false S33*1, Y7*2, U5*3 5.542,0.438 5.854,0.635 0.313,0.198 10 false 2 2.604,2.094 4.146,2.469 1.542,0.375 10 false Skid Control ECU (Brake Actuator Assembly) 4.49,1.448 6.969,1.813 2.479,0.365 10 false Tire Pressure Warning ECU and Recever 4.396,1.74 7.146,1.938 2.75,0.198 10 false *1: for Single Cab 4.406,2.042 6.552,2.24 2.146,0.198 10 false *2: for Double Cab 4.417,2.354 6.563,2.552 2.146,0.198 10 false *3: except Single and Double Cabs

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registration Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



HINT:

When the speedometer needle is not moving, first troubleshoot the meter/gauge system.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.READ VALUE USING DATA LIST (VEHICLE SPEED)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed reading min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) Actual vehicle speed Speed indicated on the combination meter assembly
Chassis > Tire Pressure Monitor > Data List
Tester Display
Vehicle Speed
50003 42 14

f.

Check that the values indicated on the GTS and on the combination meter assembly are the same.

OK:

Vehicle speed indicated on the GTS indicates the actual speed.


Result:
Proceed to
OK
NG




OK

2.CHECK DTC OUTPUT

NG

3.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - COMBINATION METER ASSEMBLY)
2.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR

Chassis > Tire Pressure Monitor > Clear DTCs
50002 42

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Perform a driving test.


e.

Check for DTCs.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR

Chassis > Tire Pressure Monitor > Trouble Codes
50001 42
HINT:

The time required for DTC C2174/74 to be stored is 20 minutes.


Result:
Result Proceed to
DTC C2174/74 is not output A
DTC C2174/74 is output B




A

B

6.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
3.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - COMBINATION METER ASSEMBLY)
a.

Turn the ignition switch off.


b.

Disconnect the S33*1, Y7*2 or U5*3 tire pressure warning ECU and receiver connector.

*1: for Single Cab

*2: for Double Cab

*3: except Single and Double Cabs



c.

Disconnect the L25 combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S33-2 (SPD) - L25-8 (+S)*1
Y7-2 (SPD) - L25-8 (+S)*2
U5-2 (SPD) - L25-8 (+S)*3
Always Below 1 Ω
S33-2 (SPD) or L25-8 (+S) - Body ground*1
Y7-2 (SPD) or L25-8 (+S) - Body ground*2
U5-2 (SPD) or L25-8 (+S) - Body ground*3
Always 10 kΩ or higher


*1: for Single Cab

*2: for Double Cab

*3: except Single and Double Cabs



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the L25 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-14 (SP1) - L25-9 (SI) Always Below 1 Ω
A42-14 (SP1) or L25-9 (SI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK DTC OUTPUT (ENGINE CONTROL SYSTEM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK DTC OUTPUT (ENGINE CONTROL SYSTEM)
a.

Clear the DTCs.


Powertrain > Engine > Clear DTCs
50002 234

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Check for DTCs.


Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0500 is not output A
DTC P0500 is output B




A

6.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

B

6.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NEXT

7.REGISTRATION OF TRANSMITTER ID
7.REGISTRATION OF TRANSMITTER ID

Result:
Proceed to
NEXT



NEXT

8.PERFORM INITIALIZATION
8.PERFORM INITIALIZATION
a.

Set the tire pressure to the specified value.

Click here



Result:
Proceed to
NEXT



NEXT

9.CHECK TEST MODE DTC (C2191/91)
9.CHECK TEST MODE DTC (C2191/91)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Tire Pressure Monitor / Utility / Signal Check.

Chassis > Tire Pressure Monitor > Utility
Tester Display
Signal Check
50005 42 3

f.

Drive the vehicle at 20 km/h (12 mph) or more for 3 seconds or more to check the vehicle speed signal (C2191/91).

Result:
Result Proceed to
DTC C2191/91 is not cleared A
DTC C2191/91 is cleared B




A

B

END