Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  C050014  Left Front Wheel Speed Sensor Circuit Short to Ground or Open  C050614  Right Front Wheel Speed Sensor Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTCs C05001F and C05061F.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>C05001F

DTC No. Detection Item DTC Detection Condition Trouble Area
C050014 Left Front Wheel Speed Sensor Circuit Short to Ground or Open An open in the speed sensor signal circuit continues for 0.5 seconds or more.
·

Front speed sensor LH

·

Skid control ECU (Brake actuator assembly)

·

Skid control sensor wire LH

·

Wire harness or connector


C050614 Right Front Wheel Speed Sensor Circuit Short to Ground or Open An open in the speed sensor signal circuit continues for 0.5 seconds or more.
·

Front speed sensor RH

·

Skid control ECU (Brake actuator assembly)

·

Skid control sensor wire RH

·

Wire harness or connector



CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>CALIBRATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Open Front speed sensor RH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".
FL Speed Open Front speed sensor LH open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".
FR Speed Sensor Voltage Open Front speed sensor RH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".
FL Speed Sensor Voltage Open Front speed sensor LH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
After a momentary interruption occurs, if there is no momentary interruption for 1 second, it switches from "Under intermittent" to "Normal".
Chassis > Brake > Data List
Tester Display
FR Speed Open
FL Speed Open
FR Speed Sensor Voltage Open
FL Speed Sensor Voltage Open
50003 435 101,102,110,111
OK:

Normal (There are no momentary interruptions.)


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (FRONT SPEED SENSOR)

NG

4.INSPECT SKID CONTROL SENSOR WIRE
2.READ VALUE USING GTS (FRONT SPEED SENSOR)
a.

According to the display on the GTS, read the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Open Front wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
FL Speed Open Front wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake > Data List
Tester Display
FR Speed Open
FL Speed Open
50003 435 101,102

b.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>PROBLEM SYMPTOMS TABLE


Result:
Proceed to
OK
NG




OK

3.RECONFIRM DTC

NG

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE)
3.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test


e.

Check if the same DTC is recorded.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs C050014 and C050614 are not output A
DTCs C050014 and/or C050614 are output B



A

B

4.INSPECT SKID CONTROL SENSOR WIRE
C494104C01
0.917,0.385 1.333,0.604 0.417,0.219 2.385,0.354 2.802,0.656 0.417,0.302 4.385,0.146 4.802,0.365 0.417,0.219 4.396,0.438 4.813,0.656 0.417,0.219 5.802,0.094 6.219,0.396 0.417,0.302 5.813,0.448 6.229,0.75 0.417,0.302 2.406,1.271 1.719,2.094 true 2.76,1.281 3.313,2.104 true 5.802,1.24 5.219,1.875 true 6.271,1.271 6.635,1.917 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *1 1.073,0.406 1.229,0.604 0.156,0.198 10 false A 2.51,0.427 2.823,0.625 0.313,0.198 10 false B3 2.906,0.313 3.219,0.51 0.313,0.198 10 false *A 2.906,0.552 3.219,0.75 0.313,0.198 10 false *C 1.385,0.313 1.698,0.51 0.313,0.198 10 false *A 4.531,0.156 4.688,0.354 0.156,0.198 10 false A 4.875,0.146 5.188,0.344 0.313,0.198 10 false *A 4.896,0.5 5.208,0.698 0.313,0.198 10 false *B 4.542,0.458 4.698,0.656 0.156,0.198 10 false B 5.917,0.156 6.229,0.354 0.313,0.198 10 false B4 6.302,0.135 6.615,0.333 0.313,0.198 10 false *A 6.521,0.135 6.833,0.333 0.313,0.198 10 false *D 5.906,0.521 6.365,0.719 0.458,0.198 10 false A21 6.323,0.521 6.635,0.719 0.313,0.198 10 false *B 1.031,1.75 1.344,1.948 0.313,0.198 10 false *a 4.552,1.729 4.865,1.927 0.313,0.198 10 false *a 2.49,2.51 2.802,2.708 0.313,0.198 10 false *b 5.948,2.021 6.26,2.219 0.313,0.198 10 false *b 1.573,2.167 2.031,2.365 0.458,0.198 10 false FR+ 3.229,2.177 3.688,2.375 0.458,0.198 10 false FR- 5,1.979 5.635,2.135 0.635,0.156 10 false FR+ (*A) 5,2.198 5.708,2.427 0.708,0.229 10 false FL+ (*B) 6.458,1.99 7.052,2.219 0.594,0.229 10 false FR- (*A) 6.458,2.219 7.052,2.448 0.594,0.229 10 false FL- (*B)
*A for RH *B for LH
*C except Pick-Up Body Type *D Pick-Up Body Type
*1 Skid Control Sensor Wire - -
*a Speed Sensor Side *b Wire Harness Side


a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A or B skid control sensor wire connector (front speed sensor side).


d.

Disconnect the B3*1, B4*2 or A21 skid control sensor wire connector (wire harness side).

*1: except Pick-Up Body Type

*2: Pick-Up Body Type



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH (except Pick-Up Body Type)
Tester Connection Condition Specified Condition
B3-2 (FR+) - A-3 Always Below 1 Ω
B3-1 (FR-) - A-1 Always Below 1 Ω
B3-2 (FR+) or A-3 - Body ground Always 10 kΩ or higher
B3-1 (FR-) or A-1 - Body ground Always 10 kΩ or higher

for RH (Pick-Up Body Type)
Tester Connection Condition Specified Condition
B4-3 (FR+) - A-3 Always Below 1 Ω
B4-1 (FR-) - A-1 Always Below 1 Ω
B4-3 (FR+) or A-3 - Body ground Always 10 kΩ or higher
B4-1 (FR-) or A-1 - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A21-3 (FL+) - B-3 Always Below 1 Ω
A21-1 (FL-) - B-1 Always Below 1 Ω
A21-3 (FL+) or B-3 - Body ground Always 10 kΩ or higher
A21-1 (FL-) or B-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE)

NG

REPLACE SKID CONTROL SENSOR WIRE

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A45 skid control ECU (brake actuator assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH (except Pick-Up Body Type)
Tester Connection Condition Specified Condition
A45-7 (FR+) - B3-2 (FR+) Always Below 1 Ω
A45-6 (FR-) - B3-1 (FR-) Always Below 1 Ω
A45-7 (FR+) or B3-2 (FR+) - Body ground Always 10 kΩ or higher
A45-6 (FR-) or B3-1 (FR-) - Body ground Always 10 kΩ or higher

for RH (Pick-Up Body Type)
Tester Connection Condition Specified Condition
A45-7 (FR+) - B4-3 (FR+) Always Below 1 Ω
A45-6 (FR-) - B4-1 (FR-) Always Below 1 Ω
A45-7 (FR+) or B4-3 (FR+) - Body ground Always 10 kΩ or higher
A45-6 (FR-) or B4-1 (FR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A45-22 (FL+) - A21-3 (FL+) Always Below 1 Ω
A45-21 (FL-) - A21-1 (FL-) Always Below 1 Ω
A45-22 (FL+) or A21-3 (FL+) - Body ground Always 10 kΩ or higher
A45-21 (FL-) or A21-1 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)
a.
C269767C08
1.583,0.115 1.781,0.313 0.198,0.198 1.583,0.396 1.781,0.583 0.198,0.188 1.802,0.063 2.115,0.219 0.313,0.156 10 false *A 1.802,0.365 2.115,0.521 0.313,0.156 10 false *B 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 1.635,0.135 1.792,0.333 0.156,0.198 10 false A 1.635,0.406 1.792,0.604 0.156,0.198 10 false B
*A for RH
*B for LH
*a Front view of wire harness connector
(to Front Speed Sensor)


Reconnect the A45 skid control ECU (brake actuator assembly) connector.


b.

Reconnect the B3*1, B4*2 or A21 skid control sensor wire connector (wire harness side).

*1: except Pick-Up Body Type

*2: Pick-Up Body Type



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
A-3 - Body ground Ignition switch ON 8 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
B-3 - Body ground Ignition switch ON 8 to 14 V



Result:
Proceed to
OK
NG



OK

NG