Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  C050C23  Left Rear Wheel Speed Sensor Signal Stuck Low  C051223  Right Rear Wheel Speed Sensor Signal Stuck Low  


DESCRIPTION

Refer to DTCs C05001F and C05061F.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>C05001F

DTC No. Detection Item DTC Detection Condition Trouble Area
C050C23 Left Rear Wheel Speed Sensor Signal Stuck Low Either of the following is detected:
1.

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.

2.

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of less than 10 km/h (6 mph) or more, outputs from both rear speed sensors are 0 km/h (0 mph) for 30 seconds or more.


·

Rear speed sensor LH

·

Sensor installation

·

Wire harness or connector

·

Skid control sensor wire

·

Rear skid control rotor LH (Rear axle hub and bearing assembly LH)


C051223 Right Rear Wheel Speed Sensor Signal Stuck Low Either of the following is detected:
1.

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.

2.

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of less than 10 km/h (6 mph) or more, outputs from both rear speed sensors are 0 km/h (0 mph) for 30 seconds or more.


·

Rear speed sensor RH

·

Sensor installation

·

Wire harness or connector

·

Skid control sensor wire

·

Rear skid control rotor RH (Rear axle hub and bearing assembly RH)



C050C23 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition When the +BS terminal voltage is 17.4 V or less ○ ○ ○
Malfunction Status At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors ○ - -
At a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) - ○ -
At a vehicle speed of 10 km/h (6 mph) or more, outputs from both rear speed sensors are 0 km/h (0 mph) - - ○
Detection Time 15 seconds or more. 1 second or more. 30 seconds or more.
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


C051223 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition When the +BS terminal voltage is 17.4 V or less ○ ○ ○
Malfunction Status At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors ○ - -
At a vehicle speed of 10 km/h (6 mph) or more, output from one of the speed sensors is 0 km/h (0 mph) - ○ -
At a vehicle speed of 10 km/h (6 mph) or more, outputs from both rear speed sensors are 0 km/h (0 mph) - - ○
Detection Time 15 seconds or more. 1 second or more. 30 seconds or more.
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


PROCEDURE

1.CHECK REAR SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C168336C14
1.994,1.633 2.181,1.795 0.186,0.161 10 *c 0.685,0.198 0.871,0.359 0.186,0.161 10 *a 2.296,0.198 2.482,0.359 0.186,0.161 10 *b
*a Normal
*b Abnormal
*c Clearance


Check the rear speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle.

The installation bolt is tightened properly.



Result:
Proceed to
OK
NG



OK

2.INSPECT REAR SPEED SENSOR TIP

NG

2.INSPECT REAR SPEED SENSOR TIP

b.

Check the speed sensor tip.


OK:

No scratches, oil, or foreign matter on the sensor tip.


NOTICE:
·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

·

If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (REAR SPEED SENSOR)

NG

CLEAN OR REPLACE REAR SPEED SENSOR

3.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

According to the display on the GTS, read the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 435 15,16

b.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>TEST MODE PROCEDURE


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

4.INSPECT SKID CONTROL SENSOR WIRE
4.INSPECT SKID CONTROL SENSOR WIRE
C269768C06
1.198,0.813 1.365,1 0.167,0.188 3.427,0.542 3.729,0.74 0.302,0.198 5.844,0.833 6.021,1.01 0.177,0.177 3.792,1.344 4.167,0.833 4.167,0.833 4.25,0.833 true 3.458,1.344 3.167,0.833 3.167,0.833 3.083,0.833 true 3.427,1.573 2.917,1.917 2.917,1.917 2.917,2.083 true 3.792,1.583 4.25,1.917 4.25,1.917 4.25,2.083 true 6.094,0.708 6.406,0.865 0.313,0.156 10 false *A 1.417,0.688 1.729,0.844 0.313,0.156 10 false *B 0.083,0.094 0.396,0.25 0.313,0.156 10 false *1 1.208,2.229 1.521,2.385 0.313,0.156 10 false *a 3.563,2.146 3.875,2.302 0.313,0.156 10 false *b 1.24,0.833 1.396,1.031 0.156,0.198 10 false D 3.5,0.563 3.823,0.75 0.323,0.188 10 false V3 5.885,0.844 6.042,1.042 0.156,0.198 10 false C 5.896,2.292 6.104,2.479 0.208,0.188 10 false *a 4.281,0.76 4.594,0.948 0.313,0.188 10 false RL- 2.781,0.75 3.083,0.917 0.302,0.167 10 false RL+ 2.823,2.094 3.125,2.271 0.302,0.177 10 false RR+ 4.167,2.125 4.469,2.313 0.302,0.188 10 false RR-
*A for RH *B for LH
*1 Skid Control Sensor Wire - -
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the C or D skid control sensor wire connector (speed sensor side).


d.

Disconnect the V3 skid control sensor wire connector (wire harness side).


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
V3-3 (RR+) - C-3 Always Below 1 Ω
V3-4 (RR-) - C-1 Always Below 1 Ω
V3-3 (RR+) or C-3 - Body ground Always 10 kΩ or higher
V3-4 (RR-) or C-1 - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
V3-1 (RL+) - D-3 Always Below 1 Ω
V3-2 (RL-) - D-1 Always Below 1 Ω
V3-1 (RL+) or D-3 - Body ground Always 10 kΩ or higher
V3-2 (RL-) or D-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE)

NG

REPLACE SKID CONTROL SENSOR WIRE

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A45 skid control ECU (brake actuator assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A45-20 (RR+) - V3-3 (RR+) Always Below 1 Ω
A45-19 (RR-) - V3-4 (RR-) Always Below 1 Ω
A45-20 (RR+) or V3-3 (RR+) - Body ground Always 10 kΩ or higher
A45-19 (RR-) or V3-4 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A45-5 (RL+) - V3-1 (RL+) Always Below 1 Ω
A45-4 (RL-) - V3-2 (RL-) Always Below 1 Ω
A45-5 (RL+) or V3-1 (RL+) - Body ground Always 10 kΩ or higher
A45-4 (RL-) or V3-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT REAR AXLE HUB AND BEARING ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT REAR AXLE HUB AND BEARING ASSEMBLY
a.

Remove the component with the rear axle hub and bearing assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL


b.

Check the rear skid control rotor.

OK:

No scratches, oil, or foreign matter on the rotors.


NOTICE:

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>TEST MODE PROCEDURE


HINT:
·

The rear skid control rotor is incorporated into the rear axle hub and bearing assembly.

·

If the rear skid control rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly.




c.

Reinstall the component with the rear axle hub and bearing assembly.

for the rear speed sensor: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR (w/ VSC)>INSTALLATION

for the rear axle hub and bearing assembly: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL


Result:
Result Proceed to
OK A
NG (The rear skid control rotor is damaged.) B
NG (There is foreign matter on the rear skid control rotor.) C



A

B

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

C

CLEAN REAR SKID CONTROL ROTOR