Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  C124A00  ECM Communication  


DESCRIPTION

The circuit is used to send TRC and VSC control information from the skid control ECU (brake actuator assembly) to the ECM, and engine control information from the ECM to the skid control ECU (brake actuator assembly) through the CAN communication system.

DTC No. Detection Item DTC Detection Condition Trouble Area
C124A00 ECM Communication Either of the following is detected:
1.

Engine model information sent from the ECM does not match the information stored in the skid control ECU.

2.

No system information stored in the skid control ECU.

3.

Incorrect installation of the skid control ECU or ECM.

4.

When the skid control ECU is malfunctioning.


·

ECM malfunction or ECM with incorrect part number installed

·

Skid control ECU (Brake actuator assembly)



C124A00 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition - - - - -
Malfunction Status Engine model information sent from the ECM does not match the information stored in the skid control ECU ○ - - -
No system information stored in the skid control ECU - ○ - -
Incorrect installation of the skid control ECU or ECM - - ○ -
When the skid control ECU is malfunctioning. - - - ○
Detection Time - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>CALIBRATION


PROCEDURE

1.CHECK PART NUMBER (ECM)
a.

Check that the proper ECM is installed.


Result:
Result Proceed to
Proper ECM is installed A
Proper ECM are not installed B



A

2.CHECK BRAKE ACTUATOR ASSEMBLY

B

2.CHECK BRAKE ACTUATOR ASSEMBLY
a.

Check if the brake actuator assembly had been replaced before the DTC was recorded.


Result:
Result Proceed to
The brake actuator assembly is not replaced A
The brake actuator assembly is replaced B



A

3.RECONFIRM DTC

B

4.PERFORM CALIBRATION
3.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Check if the same DTC is recorded.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
DTC C124A00 is not output A
DTC C124A00 is output B



A

B

4.PERFORM CALIBRATION

NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Check if the same DTC is recorded.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
DTC C124A00 is not output A
DTC C124A00 is output B



A

END

B