Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  C142771  ABS Pump Motor Actuator Stuck  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
C142771 ABS Pump Motor Actuator Stuck Actuator pump motor does not operate properly.
·

Ground circuit (Brake actuator assembly)

·

Motor circuit (Brake actuator assembly)

·

Wire harness or connector



CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>CALIBRATION


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (MOTOR RELAY)
a.

According to the display on the GTS, perform the Active Test.

Chassis > Brake > Active Test
Tester Display Measurement Item Control Range Restrict Condition Diagnostic Note
Motor Relay ABS motor relay OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 10 seconds.


-
Chassis > Brake > Active Test
Tester Display
Motor Relay
50004 435 11

b.

Check the operating sound of the motor relay when operating it with the GTS.


Result:
Result Proceed to
The operating sound is not heard A
The operating sound is heard B



A

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

B

3.RECONFIRM DTC
2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
C494113C02
1.49,0.073 1.917,0.313 0.427,0.24 0.583,1.24 0.594,1.792 true 0.438,1.865 1.052,2.063 0.615,0.198 10 false GND2 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 1.583,0.104 2.042,0.302 0.458,0.198 10 false A45
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A45 skid control ECU (brake actuator assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A45-30 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)

3.RECONFIRM DTC
HINT:

This code is detected when a problem is identified in the brake actuator assembly.

The motor relay is in the brake actuator assembly.

Therefore, motor relay unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the brake actuator assembly.


a.

Reconnect the A45 skid control ECU (brake actuator assembly) connector.


b.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


f.

Check if the same DTC is recorded.

Chassis > Brake > Trouble Codes
50001 435
HINT:
·

If a speed signal of 20 km/h (12 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (no trouble codes are output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly. Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.




Result:
Result Proceed to
DTC C142771 is not output A
DTC C142771 is output B



A

B