Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0548732 VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/ Pre-collision System)  C052C13  ABS Pump Motor Control Circuit Open  C052C49  ABS Pump Motor Control Internal Electronic Failure  C052F14  ABS Pump Motor Supply Voltage Circuit Short to Ground or Open  


DESCRIPTION

The motor relay and motor fail-safe relay are built into the brake actuator assembly.

During ABS, TRC, VSC, or brake assist operation, the skid control ECU (brake actuator assembly) turns on the motor relay to run the pump motor in the brake actuator assembly.

When a motor system DTC is stored, the motor fail-safe relay cuts the power source supply to the motor relay for fail-safe operation.

These DTCs may be stored when the voltage to the motor relay power source (BM terminal) is lower than the DTC detection condition due to low output from the battery or alternator.

DTC No. Detection Item DTC Detection Condition Trouble Area
C052C13 ABS Pump Motor Control Circuit Open Either of the following is detected:
·

When the +BS terminal voltage is from 9.5 to 17.4 V with the motor relay ON while control operates, a relay contact OFF condition continues for 0.12 seconds or more.

·

When the +BS terminal voltage is from 9.5 to 17.4 V, a motor relay supervision voltage malfunction continues for 0.12 seconds or more when the motor relay turns ON during control operation.


·

Motor relay (Brake actuator assembly)

·

Wire harness or connector


C052C49 ABS Pump Motor Control Internal Electronic Failure Any of the following is detected:
·

When the +BS terminal voltage is from 9.5 to 17.4 V, overcurrent in the motor relay and motor fail-safe relay continues for 0.05 seconds or more.

·

When the +BS terminal voltage is from 9.5 to 17.4 V, a motor relay gate voltage malfunction continues for 0.12 seconds or more.

·

Motor relay overcurrent continues for 0.05 seconds or more.


·

Motor relay (Brake actuator assembly)

·

Wire harness or connector


C052F14 ABS Pump Motor Supply Voltage Circuit Short to Ground or Open When voltage at +BS terminal is 9.5 V or higher, open in BM terminal continues for 1 second or more.
·

Skid Control ECU (Brake actuator assembly)

·

Wire harness or connector



C052C13 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When the +BS terminal voltage is from 9.5 to 17.4 V ○ ○
Malfunction Status Motor relay ON while control operates, relay contact OFF condition continues ○ -
Motor relay supervision voltage malfunction continues, motor relay turns ON during control operation - ○
Detection Time 0.12 seconds or more. 0.12 seconds or more.
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


C052C49 DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition When the +BS terminal voltage is from 9.5 to 17.4 V ○ ○ -
Malfunction Status Overcurrent in motor relay and motor fail-safe relay continues ○ - -
Motor relay gate voltage malfunction continues - ○ -
Motor relay overcurrent continues - - ○
Detection Time 0.05 seconds or more. 0.12 seconds or more. 0.05 seconds or more.
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C480601E30
4.417,2.917 4.875,3.115 0.458,0.198 10 false A45 0.427,0.979 1.833,1.375 1.406,0.396 10 false from Battery 5.021,2.438 5.969,2.656 0.948,0.219 10 false Pump Motor 4.646,1.115 6.427,1.333 1.781,0.219 10 false Skid Control ECU* 3.688,1.792 4.302,1.99 0.615,0.198 10 false GND2 3.677,1.125 4.292,1.323 0.615,0.198 10 false BM 3.406,1.531 3.708,1.74 0.302,0.208 10 false 30 3.406,0.875 3.708,1.083 0.302,0.208 10 false 46 1.99,1.167 2.938,1.385 0.948,0.219 10 false ABS MTR 4.417,3.083 6.083,3.292 1.667,0.208 10 false Brake Actuator Assembly 0.167,3.396 3.708,3.615 3.542,0.219 10 false *: Includes the motor relay and motor fail-safe relay

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When C137BA2 and/or C137BA3 is output together with C052C13, C052C49 and/or C052F14 inspect and repair the trouble areas indicated by C137BA2 and/or C137BA3 first.

for C137BA2: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>C137BA2

for C137BA3: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/ Pre-collision System)>C137BA3


PROCEDURE

1.CHECK TERMINAL VOLTAGE (BM TERMINAL)
C494113C01
1.542,0.094 2,0.333 0.458,0.24 2.823,1.24 2.823,1.813 true 2.729,1.865 3.188,2.094 0.458,0.229 10 false BM 1.635,0.135 1.938,0.344 0.302,0.208 10 false A45 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A45 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A45-46 (BM) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BM CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.
C494113C02
1.49,0.073 1.917,0.313 0.427,0.24 0.583,1.24 0.594,1.792 true 0.438,1.865 1.052,2.063 0.615,0.198 10 false GND2 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 1.583,0.104 2.042,0.302 0.458,0.198 10 false A45
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A45-30 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)

3.RECONFIRM DTC
HINT:

These codes are stored when a problem is identified in the skid control ECU (brake actuator assembly). The motor relay is in the skid control ECU (brake actuator assembly). Therefore, motor relay inspections and motor relay unit inspections cannot be performed. Be sure to check if any DTCs are output before replacing the brake actuator assembly.


a.

Reconnect the A45 skid control ECU (brake actuator assembly) connector.


b.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


f.

Check if the same DTC is recorded.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs C052C13, C052C49 and C052F14 are not output A
DTCs C052C13, C052C49 and/or C052F14 are output B


HINT:
·

If a speed signal of 20 km/h (12 mph) or more is input to the skid control ECU (brake actuator assembly), with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness from the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.




A

B