Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Pre-collision System) › from 2022.09
RM25T0E _57 Power Source / Network _057931 NETWORKING _0556385 CAN COMMUNICATION SYSTEM(w/ Pre-collision System) U

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Pre-collision System)  TERMINALS OF ECU  


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

·

After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.





CAN JUNCTION CONNECTOR


a.

No. 7 GLOBAL CAN JUNCTION CONNECTOR

C485530C09
3.427,0.323 3.865,0.615 0.438,0.292 2.667,1.302 1.844,0.854 1.844,0.854 1.635,0.854 true 2.833,1.292 2.021,0.667 2.021,0.667 1.854,0.667 true 3.052,1.302 2.302,0.521 2.302,0.521 2.146,0.521 true 3.365,1.281 2.917,0.177 2.917,0.177 2.75,0.177 true 3.229,1.292 2.583,0.354 2.583,0.354 2.417,0.354 true 2.667,1.635 1.906,1.938 1.906,1.938 1.74,1.938 true 2.844,1.625 2.125,2.146 2.125,2.146 1.969,2.146 true 3.052,1.635 2.344,2.344 2.344,2.344 2.198,2.344 true 3.219,1.635 2.552,2.521 2.552,2.521 2.406,2.521 true 3.406,1.635 2.76,2.677 2.76,2.677 2.594,2.677 true 3.625,1.281 4.281,0.146 4.281,0.146 4.438,0.146 true 3.781,1.292 4.615,0.323 4.615,0.323 4.74,0.323 true 3.969,1.292 4.833,0.479 4.833,0.479 4.969,0.479 true 4.156,1.302 5.135,0.656 5.135,0.656 5.281,0.656 true 4.354,1.302 5.302,0.844 5.302,0.844 5.427,0.844 true 4.573,1.333 5.375,1 5.375,1 5.542,1 true 3.625,1.646 4.271,2.656 4.271,2.656 4.469,2.656 true 3.823,1.635 4.75,2.51 4.75,2.51 4.917,2.51 true 3.99,1.635 4.948,2.333 4.948,2.333 5.104,2.333 true 4.146,1.625 5.104,2.135 5.104,2.135 5.271,2.135 true 4.344,1.625 5.271,1.948 5.271,1.948 5.396,1.948 true 4.583,1.594 5.438,1.802 5.438,1.802 5.594,1.792 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 3.49,0.385 3.969,0.615 0.479,0.229 10 false H134 1.094,0.771 2.01,0.969 0.917,0.198 10 false CANH*b 1.323,0.583 2.24,0.781 0.917,0.198 10 false CANH*c 1.615,0.427 2.531,0.625 0.917,0.198 10 false CANH*d 1.875,0.26 2.792,0.458 0.917,0.198 10 false CANH*e 2.219,0.094 3.135,0.292 0.917,0.198 10 false CANH*f 1.219,1.854 2.135,2.052 0.917,0.198 10 false CANL*b 1.448,2.052 2.365,2.25 0.917,0.198 10 false CANL*c 1.667,2.24 2.583,2.438 0.917,0.198 10 false CANL*d 1.875,2.427 2.792,2.625 0.917,0.198 10 false CANL*e 2.063,2.594 3.01,2.771 0.948,0.177 10 false CANL*f 4.479,0.052 5.396,0.25 0.917,0.198 10 false CANH*g 4.781,0.229 5.698,0.427 0.917,0.198 10 false CANH*h 5.01,0.396 5.927,0.594 0.917,0.198 10 false CANH*i 5.292,0.563 6.208,0.76 0.917,0.198 10 false CANH*j 5.49,0.74 6.406,0.938 0.917,0.198 10 false CANH*k 5.594,0.917 6.51,1.115 0.917,0.198 10 false CANH*l 4.49,2.552 5.49,2.76 1,0.208 10 false CANL*g 4.99,2.406 5.917,2.563 0.927,0.156 10 false CANL*h 5.146,2.24 6.073,2.396 0.927,0.156 10 false CANL*i 5.313,2.052 6.24,2.208 0.927,0.156 10 false CANL*j 5.448,1.865 6.375,2.021 0.927,0.156 10 false CANL*k 5.656,1.698 6.583,1.854 0.927,0.156 10 false CANL*l
*a Front view of wire harness connector
(to No. 7 Global CAN Junction Connector)
*b to ECM
*c to Combination Meter Assembly *d to Airbag Sensor Assembly
*e to Central Gateway ECU (Network Gateway ECU) *f to Brake Actuator Assembly (Skid Control ECU)
*g to Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) *h to Central Gateway ECU (Network Gateway ECU)
*i to Millimeter Wave Radar Sensor *j to Forward Recognition Camera (except Pick-Up)
*k to Central Gateway ECU (Network Gateway ECU) *l to Forward Recognition Camera (for Pick-Up)


No. 7 Global CAN Junction Connector Wiring Color Connect to

*1: except Pick-Up

*2: for Pick-Up

I134-1 (CANH) B ECM
I134-12 (CANL) W
I134-2 (CANH) G Combination meter assembly
I134-13 (CANL) W
I134-3 (CANH) P Airbag sensor assembly
I134-14 (CANL) W
I134-4 (CANH) SB Central gateway ECU (network gateway ECU)
I134-15 (CANL) W
I134-5 (CANH) B Brake actuator assembly (skid control ECU)
I134-16 (CANL) W
I134-6 (CANH) P Spiral with sensor cable sub-assembly (steering angle sensor)
I134-17 (CANL) W
I134-7 (CANH) B Central gateway ECU (network gateway ECU)
I134-18 (CANL) W
I134-8 (CANH) G Millimeter wave radar sensor
I134-19 (CANL) W
I134-9 (CANH) W Forward recognition camera*1
I134-20 (CANL) P
I134-10 (CANH) R Central gateway ECU (network gateway ECU)
I134-21 (CANL) W
I134-11 (CANH) L Forward recognition camera*2
I134-22 (CANL) W



CHECK DLC3


a.
C253362C36
0.167,1 0.583,1.25 0.417,0.25 1.948,0.906 2.167,0.417 2.167,0.417 2.417,0.417 true 1.583,0.906 1.25,0.5 1.25,0.5 1,0.5 true 1.927,1.49 1.667,1.917 1.667,1.917 1.417,1.917 true 2.333,1.5 2.5,1.833 2.5,1.833 2.75,1.833 true 0.25,1.031 0.708,1.229 0.458,0.198 10 false I17 0.75,0.417 1.208,0.615 0.458,0.198 10 false CG 2.469,0.344 2.927,0.542 0.458,0.198 10 false CANH 1.031,1.844 1.49,2.042 0.458,0.198 10 false CANL 2.802,1.76 3.26,1.958 0.458,0.198 10 false BAT 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a
*a Front view of DLC3


Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.




b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I17-6 (CANH) - I17-14 (CANL) L - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I17-6 (CANH) - I17-4 (CG) L - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I17-14 (CANL) - I17-4 (CG) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I17-6 (CANH) - I17-16 (BAT) L - V HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I17-14 (CANL) - I17-16 (BAT) W - V LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)


C331365C60
3.281,0.313 3.76,0.573 0.479,0.26 4.438,0.854 4.167,0.854 4.167,0.854 3.896,1.333 true 4.448,2.021 4.24,2.021 4.24,2.021 3.854,1.469 true 4.156,2.49 3.896,2.49 3.896,2.49 3.615,1.469 true 4.052,2.677 3.792,2.677 3.792,2.677 3.542,1.458 true 4.365,2.156 4.156,2.156 4.156,2.156 3.771,1.469 true 4.302,2.281 4.094,2.281 4.094,2.281 3.698,1.458 true 2.344,0.802 2.573,0.802 2.573,0.802 3.021,1.344 true 1.875,1.979 2.104,1.979 2.104,1.979 2.969,1.458 true 1.927,1.104 2.156,1.104 2.156,1.104 2.948,1.354 true 5.313,1.073 5.042,1.073 5.042,1.073 4.198,1.354 true 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a 3.385,0.365 4,0.563 0.615,0.198 10 false I130 4.51,0.76 5.177,0.969 0.667,0.208 10 false CA6L*A 4.51,1.927 5.281,2.125 0.771,0.198 10 false CA6H*A 4.208,2.406 4.833,2.625 0.625,0.219 10 false CA4L*B 4.104,2.594 4.833,2.781 0.729,0.188 10 false CA4H*B 4.406,2.073 5.177,2.271 0.771,0.198 10 false CA5H*C 4.333,2.219 5,2.427 0.667,0.208 10 false CA5L*C 1.792,0.719 2.375,0.927 0.583,0.208 10 false CAXH*C 1.323,1.896 1.906,2.104 0.583,0.208 10 false CAXL*C 5.344,0.979 6.01,1.188 0.667,0.208 10 false BATT 1.583,1.021 2.25,1.229 0.667,0.208 10 false GND
*A V Bus *B Bus 2
*C Bus 5 - -
*a Component without harness connected
(Central Gateway ECU [Network Gateway ECU])
- -


a.
C495032C01
1.667,0.208 2.198,0.458 0.531,0.25 1.094,1.875 1.24,1.875 1.24,1.875 1.667,1.271 true 1.323,2.052 1.469,2.052 1.469,2.052 1.771,1.271 true 2.823,0.729 2.667,0.729 2.667,0.729 2.469,1.115 true 2.844,1.542 2.729,1.542 2.729,1.542 2.563,1.281 true 0.719,0.677 0.865,0.677 0.865,0.677 1.302,1.094 true 0.927,0.458 1.073,0.458 1.073,0.458 1.573,1.26 true 2.906,1.021 2.75,1.021 2.75,1.021 2.604,1.115 true 0.448,1.344 0.594,1.344 0.594,1.344 0.823,1.115 true 0.667,1.688 0.813,1.688 0.813,1.688 1.479,1.271 true 0.615,0.865 0.76,0.865 0.76,0.865 1.365,1.271 true 1.771,0.25 2.188,0.427 0.417,0.177 10 false I130 0.073,0.104 0.385,0.26 0.313,0.156 10 false *a 0.781,1.938 1.375,2.167 0.594,0.229 10 false CA4H*A 0.563,1.781 1.156,2.01 0.594,0.229 10 false CA4L*A 2.875,0.615 3.427,0.844 0.552,0.229 10 false CAXH*B 2.885,1.438 3.396,1.698 0.51,0.26 10 false CAXL*B 0.396,0.344 0.906,0.604 0.51,0.26 10 false CA5L*B 0.177,0.573 0.76,0.823 0.583,0.25 10 false CA6L*C 2.958,0.938 3.354,1.208 0.396,0.271 10 false GND 0.104,1.25 0.563,1.521 0.458,0.271 10 false BATT 0.094,1.573 0.677,1.823 0.583,0.25 10 false CA5H*B 0.063,0.792 0.646,1.042 0.583,0.25 10 false CA6H*C
*A Bus 2
*B Bus 5
*C V Bus
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Disconnect the central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

V Bus
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I130-14 (CA6H) - I130-5 (CA6L) L - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 1 MΩ or higher
I130-14 (CA6H) - I130-10 (GND) L - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I130-5 (CA6L) - I130-10 (GND) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I130-14 (CA6H) - I130-1 (BATT) L - P HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I130-5 (CA6L) - I130-1 (BATT) W - P LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 2
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I130-18 (CA4H) - I130-17 (CA4L) SB - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I130-18 (CA4H) - I130-10 (GND) SB - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I130-17 (CA4L) - I130-10 (GND) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I130-18 (CA4H) - I130-1 (BATT) SB - P HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I130-17 (CA4L) - I130-1 (BATT) W - P LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 5
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I130-15 (CA5H) - I130-16 (CA5L) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 1 MΩ or higher
I130-15 (CA5H) - I130-9 (CAXH) B - R HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) battery terminal Below 1 Ω
I130-16 (CA5L) - I130-24 (CAXL) W - W LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal Below 1 Ω
I130-15 (CA5H) - I130-10 (GND) B - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I130-16 (CA5L) - I130-10 (GND) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I130-15 (CA5H) - I130-1 (BATT) B - P HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I130-16 (CA5L) - I130-1 (BATT) W - P LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>PRE-COLLISION>FRONT RADAR SENSOR SYSTEM>TERMINALS OF ECU

a.
C339037C24
0.25,2.396 0.719,2.646 0.469,0.25 2.51,0.625 2.979,0.875 0.469,0.25 2.313,2.771 2.573,3.021 2.573,3.021 2.75,3.021 true 0.792,0.635 0.948,0.635 0.948,0.635 1.458,0.865 true 1.052,0.365 1.208,0.365 1.208,0.365 1.625,0.844 true 1.323,0.156 1.479,0.156 1.479,0.156 1.75,0.854 true 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 0.115,1.833 0.427,1.99 0.313,0.156 10 false *b 0.365,2.438 0.677,2.594 0.313,0.156 10 false I17 2.625,0.677 2.969,0.917 0.344,0.24 10 false I131 2.802,2.885 3.24,3.063 0.438,0.177 10 false BAT 0.375,0.531 0.969,0.708 0.594,0.177 10 false SGND 0.667,0.271 1.26,0.448 0.594,0.177 10 false CA2L 0.938,0.073 1.531,0.25 0.594,0.177 10 false CA2H
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
*b Front view of DLC3


Disconnect the millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I131-3 (CA2H) - I131-2 (CA2L) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I131-3 (CA2H) - I131-1 (SGND) G - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I131-2 (CA2L) - I131-1 (SGND) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I131-3 (CA2H) - I17-16 (BAT) G - V HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I131-2 (CA2L) - I17-16 (BAT) W - V LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK FORWARD RECOGNITION CAMERA (w/ Pre-collision System)


Refer to Terminals of ECU.

Click hereVehicle Interior>PRE-COLLISION>FRONT CAMERA SYSTEM>TERMINALS OF ECU

a.
B631355C02
1.417,2.5 1.833,2.833 0.417,0.333 0.292,1.125 0.708,1.458 0.417,0.333 0.271,0.615 0.688,0.948 0.417,0.333 2.25,4.25 2,4.25 2,4.25 2.365,3.729 true 2.417,0.167 2.167,0.167 2.167,0.167 2,1.052 true 2.417,1.917 2.167,1.917 2.167,1.917 2,1.302 true 2.333,2.167 2.083,2.167 2.083,2.167 1.813,1.302 true 0.583,0.094 0.896,0.25 0.313,0.156 10 false *a 0.771,2.427 1.083,2.583 0.313,0.156 10 false *b 0.396,0.698 0.854,0.896 0.458,0.198 10 false Y8 1.521,2.583 1.833,2.781 0.313,0.198 10 false I17 2.333,4.167 2.792,4.365 0.458,0.198 10 false BAT 2.51,0.094 3.125,0.292 0.615,0.198 10 false CA1P 2.5,1.875 3.115,2.073 0.615,0.198 10 false CA1N 2.396,2.094 3.01,2.292 0.615,0.198 10 false GND 0.729,0.698 1.042,0.854 0.313,0.156 10 false *A 0.74,1.208 1.052,1.365 0.313,0.156 10 false *B 0.385,1.219 0.844,1.417 0.458,0.198 10 false S34
*A except Pick-Up
*B for Pick-Up
*a Front view of wire harness connector
(to Forward Recognition Camera)
*b Front view of DLC3


Disconnect the forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

except Pick-Up
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Y8-5 (CA1P) - Y8-11 (CA1N) W - P HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
Y8-5 (CA1P) - Y8-10 (GND) W - B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
Y8-11 (CA1N) - Y8-10 (GND) P - B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
Y8-5 (CA1P) - I17-16 (BAT) W - V HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Y8-11 (CA1N) - I17-16 (BAT) P - V LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for Pick-Up
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S34-5 (CA1P) - S34-11 (CA1N) L - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
S34-5 (CA1P) - S34-10 (GND) L - B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
S34-11 (CA1N) - S34-10 (GND) W - B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
S34-5 (CA1P) - I17-16 (BAT) L - V HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
S34-11 (CA1N) - I17-16 (BAT) W - V LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)


Refer to Terminals of ECU for Vehicle Stability Control System for further details.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TERMINALS OF ECU

a.
C494974C01
0.573,0.208 1.063,0.427 0.49,0.219 2.406,0.948 2.688,0.302 2.688,0.302 2.865,0.302 true 2.052,1.156 1.938,0.208 1.938,0.208 2.135,0.208 true 2.073,1.292 2.177,1.906 2.177,1.906 2.344,1.906 true 0.458,1.51 0.604,1.51 0.604,1.51 0.885,1.052 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 0.677,0.24 0.99,0.396 0.313,0.156 10 false A45 2.156,0.135 2.656,0.375 0.5,0.24 10 false CANL 2.375,1.844 2.875,2.083 0.5,0.24 10 false CANH 2.896,0.24 3.292,0.5 0.396,0.26 10 false +BS 0.083,1.417 0.479,1.677 0.396,0.26 10 false GND1
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A45-43 (CANH) - A45-27 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A45-43 (CANH) - A45-1 (GND1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A45-27 (CANL) - A45-1 (GND1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A45-43 (CANH) - A45-14 (+BS) B - R HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A45-27 (CANL) - A45-14 (+BS) W - R LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>TERMINALS OF ECM

a.

Disconnect the ECM connectors.

C234869C20
1.99,0.458 2.458,0.729 0.469,0.271 4.594,0.5 5.063,0.771 0.469,0.271 5.813,2.313 5.51,2.313 5.51,2.313 5.208,1.646 true 1.115,1.01 1.333,1.01 1.333,1.01 1.865,1.385 true 2.333,2.333 2.5,2.333 2.5,2.333 2.781,1.729 true 3.385,2.292 3.083,2.292 3.083,2.292 2.781,1.625 true 2.104,0.51 2.396,0.688 0.292,0.177 10 false A29 0.125,0.073 0.417,0.25 0.292,0.177 10 false *a 5.875,2.198 6.74,2.365 0.865,0.167 10 false E1 4.708,0.552 5.042,0.729 0.333,0.177 10 false C39 0.76,0.917 1.188,1.083 0.427,0.167 10 false BATT 1.948,2.26 2.375,2.427 0.427,0.167 10 false CANL 3.458,2.219 3.885,2.385 0.427,0.167 10 false CANH
*a Front view of wire harness connector
(to ECM)
- -



b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A29-41 (CANH) - A29-49 (CANL) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A29-41 (CANH) - C39-81 (E1) G - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A29-49 (CANL) - C39-81 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A29-41 (CANH) - A29-20 (BATT) G - R-B HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A29-49 (CANL) - A29-20 (BATT) W - R-B LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK COMBINATION METER ASSEMBLY


Refer to Terminals of ECU for Meter / Gauge System for further details.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU

a.
C363467C01
1.406,0.25 2.073,0.531 0.667,0.281 1.448,2.365 2.115,2.646 0.667,0.281 0.323,2.104 0.51,2.104 0.51,2.104 0.667,1.667 true 2.938,2.063 2.76,2.063 2.76,2.063 2.531,1.656 true 0.479,4.146 0.667,4.146 0.667,4.146 0.823,3.708 true 0.729,4.396 0.917,4.396 0.917,4.396 1.01,3.74 true 0.198,0.188 0.51,0.344 0.313,0.156 10 false *a 0.073,4.042 0.604,4.417 0.531,0.375 10 false CANH 0.313,4.271 1,4.563 0.688,0.292 10 false CANL 1.563,0.271 2.031,0.51 0.469,0.24 10 false L25 1.625,2.396 2.094,2.635 0.469,0.24 10 false L26 0.104,2 0.635,2.375 0.531,0.375 10 false ES 3.01,1.958 3.427,2.198 0.417,0.24 10 false B
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L26-13 (CANH) - L26-14 (CANL) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
L26-13 (CANH) - L25-15 (ES) G - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
L26-14 (CANL) - L25-15 (ES) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
L26-13 (CANH) - L25-26 (B) G - V HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
L26-14 (CANL) - L25-26 (B) W - V LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIRBAG SENSOR ASSEMBLY


Refer to Terminals of ECU for Airbag System for further details.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU

a.
C227529C10
0.375,2.521 0.771,2.781 0.396,0.26 0.365,0.948 0.76,1.208 0.396,0.26 2.198,2.896 2.333,3.115 2.333,3.115 2.552,3.115 true 2.115,1.323 2.313,1.677 2.313,1.677 2.552,1.677 true 2.021,1.01 2.438,0.656 2.438,0.656 2.688,0.656 true 1.208,1.677 1.438,1.677 1.438,1.677 1.76,1.323 true 0.177,0.073 0.427,0.271 0.25,0.198 10 false *a 0.198,2.083 0.51,2.24 0.313,0.156 10 false *b 0.49,2.552 0.833,2.76 0.344,0.208 10 false I17 0.458,0.979 0.802,1.188 0.344,0.208 10 false I51 2.75,0.583 3.292,0.792 0.542,0.208 10 false CANH 2.604,1.604 3.146,1.813 0.542,0.208 10 false CANL 2.604,3.042 3.146,3.25 0.542,0.208 10 false BAT 1,1.604 1.542,1.813 0.542,0.208 10 false E1
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of DLC3


Disconnect the airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I51-13 (CANH) - I51-22 (CANL) P - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I51-13 (CANH) - I51-25 (E1) P - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I51-22 (CANL) - I51-25 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I51-13 (CANH) - I17-16 (BAT) P - V HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I51-22 (CANL) - I17-16 (BAT) W - V LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)


C201866E09
2.719,1.01 3.26,1.25 0.542,0.24 1.969,1.188 1.635,0.594 1.635,0.594 1.563,0.594 true 2.354,1.188 2.688,0.823 2.688,0.823 2.76,0.823 true 2.25,1.198 2.583,0.5 2.583,0.5 2.656,0.5 true 2.156,1.177 2.323,0.26 2.323,0.26 2.396,0.26 true 2.698,0.396 3.198,0.625 0.5,0.229 10 false CANL 1.24,0.479 1.552,0.646 0.313,0.167 10 false BAT 2.854,1.042 3.167,1.208 0.313,0.167 10 false L47 2.802,0.719 3.302,0.948 0.5,0.229 10 false ESS 2.448,0.156 2.896,0.323 0.448,0.167 10 false CANH

a.
C198943C16
0.656,1.323 1.26,1.573 0.604,0.25 2.125,1.542 2.375,1.115 2.375,1.115 2.458,1.115 true 2.24,1.552 2.615,1.385 2.615,1.385 2.698,1.385 true 2.042,1.552 1.719,1.083 1.719,1.083 1.646,1.083 true 1.802,1.625 1.552,1.906 1.552,1.906 1.385,1.906 true 1.229,0.979 1.646,1.177 0.417,0.198 10 false CANH 0.833,1.344 1.115,1.521 0.281,0.177 10 false L47 0.167,0.052 0.594,0.25 0.427,0.198 10 false *a 2.521,0.979 2.938,1.177 0.417,0.198 10 false CANL 2.771,1.271 3.188,1.469 0.417,0.198 10 false ESS 1.052,1.781 1.469,1.979 0.417,0.198 10 false BAT
*a Rear view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])


Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L47-4 (CANH) - L47-3 (CANL) P - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
L47-4 (CANH) - L47-2 (ESS) P - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
L47-3 (CANL) - L47-2 (ESS) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
L47-4 (CANH) - L47-6 (BAT) P - B HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
L47-3 (CANL) - L47-6 (BAT) W - B LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher