Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for RHD with VSC) › from 2022.09
RM25T0E _57 Power Source / Network _057931 NETWORKING _0306319 CAN COMMUNICATION SYSTEM(for RHD with VSC) U

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with VSC)  TERMINALS OF ECU  


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

·

When disconnecting and reconnecting the battery.

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.





CAN JUNCTION CONNECTOR


a.

NO. 4 CAN JUNCTION CONNECTOR

HINT:

Connectors that connect to the No. 4 CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the No. 4 CAN junction connector, reconnecting the connectors to non-original positions on the No. 4 CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


C363464C01
5.875,2.792 6.083,2.583 6.083,2.583 6.25,2.583 true 5.885,2.948 6.052,3.292 6.052,3.292 6.219,3.292 true 6.292,2.458 6.906,2.656 0.615,0.198 10 false CANH 6.26,3.188 6.875,3.385 0.615,0.198 10 false CANL 4.865,2.156 5.479,2.354 0.615,0.198 10 false *a 0.188,0.115 0.802,0.313 0.615,0.198 10 false *1 1.979,0.833 2.594,1.031 0.615,0.198 10 false I116 1.969,1.125 2.583,1.323 0.615,0.198 10 false I115 3.552,1.406 4.167,1.604 0.615,0.198 10 false I114 3.552,1.677 4.167,1.875 0.615,0.198 10 false I112 1.969,1.406 2.583,1.604 0.615,0.198 10 false I113
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -


No. 4 CAN Junction Connector Wiring Color Connect to
I112-1 (CANH) G Combination meter assembly
I112-2 (CANL) W
I113-1 (CANH) L DLC3
I113-2 (CANL) W
I114-1 (CANH) P Spiral with sensor cable sub-assembly (steering angle sensor)
I114-2 (CANL) W
I115-1 (CANH) B No. 5 CAN junction connector
I115-2 (CANL) W
I116-1 (CANH) P Airbag sensor assembly
I116-2 (CANL) W


b.

NO. 5 CAN JUNCTION CONNECTOR

C363465C01
3.188,0.479 3.823,0.74 0.635,0.26 3.635,1.469 4.021,0.792 4.021,0.792 4.229,0.792 true 2.635,0.802 2.927,0.802 2.927,0.802 3.51,1.5 true 2.771,2.25 3.031,2.25 3.031,2.25 3.51,1.771 true 3.646,1.771 3.917,2.438 3.917,2.438 4.125,2.438 true 3.948,1.76 4.24,2.167 4.24,2.167 4.448,2.167 true 3.948,1.49 4.396,1.167 4.396,1.167 4.604,1.167 true 2.042,0.677 2.958,0.875 0.917,0.198 10 false CANH*b 4.302,0.688 5.219,0.885 0.917,0.198 10 false CANH*c 4.688,1.052 5.604,1.25 0.917,0.198 10 false CANH*d 2.24,2.135 3.156,2.333 0.917,0.198 10 false CANL*b 4.198,2.333 5.115,2.531 0.917,0.198 10 false CANL*c 4.51,2.042 5.427,2.24 0.917,0.198 10 false CANL*d 0.125,0.125 1.042,0.323 0.917,0.198 10 false *a 3.333,0.51 4.25,0.708 0.917,0.198 10 false I111
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b for ECM
*c for Brake Actuator Assembly (Skid Control ECU) *d for No. 4 CAN Junction Connector


No. 5 CAN Junction Connector Wiring Color Connect to
I111-3 (CANH) B ECM
I111-9 (CANL) W
I111-4 (CANH) B Brake actuator assembly (skid control ECU)
I111-10 (CANL) W
I111-6 (CANH) B No. 4 CAN junction connector
I111-12 (CANL) W



CHECK DLC3


a.
C253362C36
0.167,1 0.583,1.25 0.417,0.25 1.948,0.906 2.167,0.417 2.167,0.417 2.417,0.417 true 1.583,0.906 1.25,0.5 1.25,0.5 1,0.5 true 1.927,1.49 1.667,1.917 1.667,1.917 1.417,1.917 true 2.333,1.5 2.5,1.833 2.5,1.833 2.75,1.833 true 0.25,1.031 0.708,1.229 0.458,0.198 10 false I17 0.75,0.417 1.208,0.615 0.458,0.198 10 false CG 2.469,0.344 2.927,0.542 0.458,0.198 10 false CANH 1.031,1.844 1.49,2.042 0.458,0.198 10 false CANL 2.802,1.76 3.26,1.958 0.458,0.198 10 false BAT 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a
*a Front view of DLC3


Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.




b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I17-6 (CANH) - I17-14 (CANL) L - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I17-6 (CANH) - I17-4 (CG) L - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I17-14 (CANL) - I17-4 (CG) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I17-6 (CANH) - I17-16 (BAT) L - V HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I17-14 (CANL) - I17-16 (BAT) W - V LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK ECM


Refer to Terminals of ECU for ECD System for further details.

w/o DPF: Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>TERMINALS OF ECM

w/ DPF: Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>TERMINALS OF ECM

a.

Disconnect the ECM connectors.

C234869C13
2.042,0.51 2.51,0.781 0.469,0.271 5.094,0.479 5.563,0.75 0.469,0.271 1.302,0.833 1.521,0.833 1.521,0.833 1.865,1.365 true 3.219,2.229 3.083,2.229 3.083,2.229 2.781,1.625 true 5.927,2.385 5.625,2.385 5.625,2.385 5.208,1.635 true 3.031,2.479 2.896,2.479 2.896,2.479 2.76,1.719 true 2.156,0.521 2.448,0.698 0.292,0.177 10 false A29 0.177,0.125 0.469,0.302 0.292,0.177 10 false *a 0.906,0.719 1.333,0.885 0.427,0.167 10 false BATT 5.979,2.271 6.844,2.438 0.865,0.167 10 false E1 5.198,0.521 5.531,0.698 0.333,0.177 10 false C39 3.083,2.354 3.948,2.521 0.865,0.167 10 false CANL 3.26,2.104 4.125,2.271 0.865,0.167 10 false CANH
*a Front view of wire harness connector
(to ECM)
- -



b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A29-41 (CANH) - A29-49 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A29-41 (CANH) - C39-81 (E1) B - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A29-49 (CANL) - C39-81 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A29-41 (CANH) - A29-20 (BATT) B - R-B HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A29-41 (CANH) - A29-20 (BATT) W - R-B LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK COMBINATION METER ASSEMBLY


Refer to Terminals of ECU for Meter / Gauge System for further details.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU

a.
C363467C01
1.406,0.25 2.073,0.531 0.667,0.281 1.448,2.365 2.115,2.646 0.667,0.281 0.323,2.104 0.51,2.104 0.51,2.104 0.667,1.667 true 2.938,2.063 2.76,2.063 2.76,2.063 2.531,1.656 true 0.479,4.146 0.667,4.146 0.667,4.146 0.823,3.708 true 0.729,4.396 0.917,4.396 0.917,4.396 1.01,3.74 true 0.198,0.188 0.51,0.344 0.313,0.156 10 false *a 0.073,4.042 0.604,4.417 0.531,0.375 10 false CANH 0.313,4.271 1,4.563 0.688,0.292 10 false CANL 1.563,0.271 2.031,0.51 0.469,0.24 10 false L25 1.625,2.396 2.094,2.635 0.469,0.24 10 false L26 0.104,2 0.635,2.375 0.531,0.375 10 false ES 3.01,1.958 3.427,2.198 0.417,0.24 10 false B
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L26-13 (CANH) - L26-14 (CANL) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
L26-13 (CANH) - L25-15 (ES) G - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
L26-14 (CANL) - L25-15 (ES) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
L26-13 (CANH) - L25-26 (B) G - R HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
L26-14 (CANL) - L25-26 (B) W - R LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK AIRBAG SENSOR ASSEMBLY


Refer to Terminals of ECU for Airbag System for further details.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU

a.
C227529C10
0.375,2.521 0.771,2.781 0.396,0.26 0.365,0.948 0.76,1.208 0.396,0.26 2.198,2.896 2.333,3.115 2.333,3.115 2.552,3.115 true 2.115,1.323 2.313,1.677 2.313,1.677 2.552,1.677 true 2.021,1.01 2.438,0.656 2.438,0.656 2.688,0.656 true 1.208,1.677 1.438,1.677 1.438,1.677 1.76,1.323 true 0.177,0.073 0.427,0.271 0.25,0.198 10 false *a 0.198,2.083 0.51,2.24 0.313,0.156 10 false *b 0.49,2.552 0.833,2.76 0.344,0.208 10 false I17 0.458,0.979 0.802,1.188 0.344,0.208 10 false I51 2.75,0.583 3.292,0.792 0.542,0.208 10 false CANH 2.604,1.604 3.146,1.813 0.542,0.208 10 false CANL 2.604,3.042 3.146,3.25 0.542,0.208 10 false BAT 1,1.604 1.542,1.813 0.542,0.208 10 false E1
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of DLC3


Disconnect the airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I51-13 (CANH) - I51-22 (CANL) P - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I51-13 (CANH) - I51-25 (E1) P - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I51-22 (CANL) - I51-25 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
I51-13 (CANH) - I17-16 (BAT) P - V HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I51-22 (CANL) - I17-16 (BAT) W - V LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)


Refer to Terminals of ECU for Vehicle Stability Control System for further details.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TERMINALS OF ECU

a.
C364734C01
0.573,0.208 1.063,0.427 0.49,0.219 2.094,1.052 2.552,0.458 2.552,0.458 2.719,0.458 true 2.042,1.167 1.813,0.188 1.813,0.188 1.979,0.188 true 2.573,1.344 2.677,1.958 2.677,1.958 2.844,1.958 true 0.51,1.938 0.698,1.938 0.698,1.938 0.854,1.344 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 0.677,0.229 0.99,0.385 0.313,0.156 10 false A42 2.781,0.354 3.281,0.594 0.5,0.24 10 false CANL 2.031,0.104 2.531,0.344 0.5,0.24 10 false CANH 2.906,1.885 3.302,2.146 0.396,0.26 10 false +BS 0.073,1.833 0.469,2.094 0.396,0.26 10 false GND1
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A42-22 (CANH) - A42-10 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A42-22 (CANH) - A42-25 (GND1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A42-10 (CANL) - A42-25 (GND1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A42-22 (CANH) - A42-38 (+BS) B - R HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A42-10 (CANL) - A42-38 (+BS) W - R LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CHECK SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (STEERING ANGLE SENSOR)


C201866E09
2.719,1.01 3.26,1.25 0.542,0.24 1.969,1.188 1.635,0.594 1.635,0.594 1.563,0.594 true 2.354,1.188 2.688,0.823 2.688,0.823 2.76,0.823 true 2.25,1.198 2.583,0.5 2.583,0.5 2.656,0.5 true 2.156,1.177 2.323,0.26 2.323,0.26 2.396,0.26 true 2.698,0.396 3.198,0.625 0.5,0.229 10 false CANL 1.24,0.479 1.552,0.646 0.313,0.167 10 false BAT 2.854,1.042 3.167,1.208 0.313,0.167 10 false L47 2.802,0.719 3.302,0.948 0.5,0.229 10 false ESS 2.448,0.156 2.896,0.323 0.448,0.167 10 false CANH

a.
C198943C16
0.656,1.323 1.26,1.573 0.604,0.25 2.125,1.542 2.375,1.115 2.375,1.115 2.458,1.115 true 2.24,1.552 2.615,1.385 2.615,1.385 2.698,1.385 true 2.042,1.552 1.719,1.083 1.719,1.083 1.646,1.083 true 1.802,1.625 1.552,1.906 1.552,1.906 1.385,1.906 true 1.229,0.979 1.646,1.177 0.417,0.198 10 false CANH 0.833,1.344 1.115,1.521 0.281,0.177 10 false L47 0.167,0.052 0.594,0.25 0.427,0.198 10 false *a 2.521,0.979 2.938,1.177 0.417,0.198 10 false CANL 2.771,1.271 3.188,1.469 0.417,0.198 10 false ESS 1.052,1.781 1.469,1.979 0.417,0.198 10 false BAT
*a Rear view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])


Disconnect the spiral cable with sensor sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L47-4 (CANH) - L47-3 (CANL) P - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
L47-4 (CANH) - L47-2 (ESS) P - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
L47-3 (CANL) - L47-2 (ESS) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
L47-4 (CANH) - L47-6 (BAT) P - B HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
L47-3 (CANL) - L47-6 (BAT) W - B LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher