1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
51442 3.REMOVE NO. 2 ENGINE UNDER COVER
4.DRAIN ENGINE COOLANT
17940D 5.REMOVE INTERCOOLER ASSEMBLY
17971 6.REMOVE NO. 1 COOL AIR INLET
17972 7.REMOVE NO. 2 COOL AIR INLET
26100G 8.REMOVE DIESEL THROTTLE BODY ASSEMBLY (for Bank 1)
26100G 9.REMOVE DIESEL THROTTLE BODY ASSEMBLY (for Bank 2)
15301 10.REMOVE ENGINE OIL LEVEL DIPSTICK
12142 11.REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE
Remove the bolt and No. 2 engine oil level dipstick guide.
Remove the O-ring from the No. 2 engine oil level dipstick guide.
16267 12.DISCONNECT NO. 2 AND NO. 3 WATER BY-PASS HOSES
Slide the 2 clamps and disconnect the No. 2 water by-pass hose and No. 3 water by-pass hoses.
23284A 13.REMOVE NO. 5 FUEL HOSE
Slide the 2 clamps and remove the No. 5 fuel hose.
23804D 14.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY
| *1 | No. 2 Fuel hose |
| *2 | No. 4 Fuel Pipe Sub-assembly |
Slide the clamp and disconnect the No. 2 fuel hose.
Remove the 2 bolts and No. 4 fuel pipe sub-assembly.
44769 15.REMOVE VACUUM RESERVOIR CONNECT TUBE
Slide the 2 clamps and disconnect the 2 vacuum hoses.
Remove the 4 bolts and vacuum reservoir connect tube.
82122 16.DISCONNECT NO. 2 ENGINE WIRE
Remove the 2 bolts and disconnect the No. 2 engine wire.
44761 17.REMOVE VACUUM PUMP TO CONNECTOR TUBE
Disconnect the engine wire clamp.
Slide the clamp and disconnect the union to connector tube hose.
Remove the 3 bolts and vacuum pump to connector tube.
25850 18.REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY
16288 19.REMOVE NO. 4 WATER BY-PASS PIPE
w/ EGR System:
Slide the 3 clamps and disconnect the inlet water hose, No. 4 water by-pass hose and No. 7 water by-pass hoses.
Remove the 2 bolts, nut and No. 4 water by-pass pipe.
w/o EGR System:
Slide the 2 clamps and disconnect the inlet water hose and No. 7 water by-pass hoses.
Remove the 2 bolts, nut and No. 4 water by-pass pipe.
16278 20.REMOVE NO. 2 WATER BY-PASS PIPE
Slide the clamp and remove the No. 2 water by-pass pipe.
23243C 21.REMOVE FUEL PUMP MOTOR WIRE
Remove the bolt and bracket.
Disconnect the fuel pump motor connector.
82121 22.DISCONNECT ENGINE WIRE
RH Side:
Disconnect the 2 connectors.
Disconnect the 4 fuel injector connectors.
Remove the 4 bolts.
Detach the 2 clamps and disconnect the engine wire.
LH Side:
Disconnect the 2 connectors.
Disconnect the 4 fuel injector connectors.
Remove the 7 bolts and disconnect the engine wire.
Rear Side:
Remove the 2 bolts and disconnect the 2 ground wires.
Detach the clamp from the No. 3 intercooler support bracket.
Remove the 2 bolts and disconnect the 2 wire harness brackets.
23265 23.REMOVE NO. 1 GAS FILTER
Disconnect the hose from the intake pipe.
Remove the No. 1 gas filter.
17947B 24.REMOVE NO. 3 INTERCOOLER SUPPORT BRACKET
Remove the 2 bolts and No. 3 intercooler support bracket.
25.REMOVE INJECTION PIPE RH
After removing the fuel pipe, to prevent dirt or foreign objects from entering the pipe inlet, cover the common rail with electrical tape. Also protect the injector inlets with electrical tape or plastic bags.
Using a 17 mm union nut wrench, loosen the union nuts and remove the 4 injection pipes.
26.REMOVE INJECTION PIPE LH
After removing the fuel pipe, to prevent dirt or foreign objects from entering the pipe inlet, cover the common rail with electrical tape. Also protect the injector inlets with electrical tape or plastic bags.
Using a 17 mm union nut wrench, loosen the union nuts and remove the 4 injection pipes.
23706 27.REMOVE NO. 6 INJECTION PIPE SUB-ASSEMBLY
After removing the fuel pipe, to prevent dirt or foreign objects from entering the pipe inlet, cover the common rail with electrical tape. Also protect the injector inlets with electrical tape or plastic bags.
w/ EGR System:
Using a union nut wrench, loosen the No. 6 injection pipe ends.
Remove the 2 nuts and 2 No. 2 injection pipe clamps.
Remove the No. 6 injection pipe sub-assembly.
w/o EGR System:
Using a union nut wrench, loosen the No. 6 injection pipe ends.
Remove the nut and No. 2 injection pipe clamp.
Remove the bolt and No. 6 injection pipe sub-assembly.
23239D 28.REMOVE NO. 1 FUEL HOSE
23805B 29.REMOVE NO. 5 FUEL PIPE SUB-ASSEMBLY
Remove the bolt and No. 2 injection pipe clamp.
Slide the clamp and disconnect the No. 3 fuel hose.
Remove the nut, union bolt, No. 5 fuel pipe sub-assembly and gasket.
23705 30.REMOVE NO. 5 INJECTION PIPE SUB-ASSEMBLY
23820A 31.REMOVE COMMON RAIL RH
23810A 32.REMOVE COMMON RAIL LH
23801L 33.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY
Slide the 2 clamps and disconnect the fuel pump hose and No. 1 fuel hoses.
Remove the bolt and fuel filter to injection pump fuel pipe sub-assembly.
25614 34.REMOVE NO. 4 EGR PIPE (w/ EGR System)
Remove the 4 bolts, No. 4 EGR pipe and 2 gaskets.
17113 35.REMOVE INTAKE PIPE
w/ EGR System:
Remove the 2 nuts, 4 bolts, intake pipe and gasket.
w/o EGR System:
Remove the 2 nuts, 4 bolts, intake pipe and gasket.
17114D 36.REMOVE NO. 3 INTAKE MANIFOLD
Remove the 16 bolts, 2 gaskets and No. 3 intake manifold.
16289 37.DISCONNECT NO. 5 WATER BY-PASS PIPE
25601 38.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (w/ EGR System)
25602 39.REMOVE NO. 2 EGR PIPE SUB-ASSEMBLY (w/ EGR System)
40.REMOVE EGR VALVE WITH EGR COOLER (w/ EGR System)
16283 41.REMOVE NO. 6 WATER BY-PASS HOSE
23764A 42.REMOVE NO. 4 NOZZLE LEAKAGE PIPE
23763 43.REMOVE NO. 3 NOZZLE LEAKAGE PIPE
23920A 44.REMOVE FUEL COOLER
16268 45.REMOVE NO. 1 WATER BY-PASS PIPE
Remove the union bolt and gasket.
Remove the bolt and No. 1 water by-pass pipe.
46.REMOVE STARTER HOSE BRACKET SUB-ASSEMBLY
17111 47.REMOVE NO. 1 INTAKE MANIFOLD
Remove the 8 bolts, No. 1 intake manifold and gasket.
17112 48.REMOVE NO. 2 INTAKE MANIFOLD
Remove the 9 bolts, No. 2 intake manifold and gasket.