Home › Drivetrain › R151F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION ASSEMBLY › from 2022.09
RM25T0E _52 Drivetrain _029903 R151F MANUAL TRANSMISSION / TRANSAXLE _0137693 MANUAL TRANSMISSION ASSEMBLY A

R151F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

CAUTION:

Be sure to read precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Hide 51442 3.REMOVE NO. 2 ENGINE UNDER COVER

Hide 17705 5.REMOVE AIR CLEANER CAP AND HOSE SUB-ASSEMBLY

Hide 16470 6.REMOVE RADIATOR RESERVOIR ASSEMBLY

Hide 88310A 7.REMOVE NO. 1 V BELT (w/ Air Conditioning System)

Hide 16571 8.REMOVE RADIATOR HOSE INLET

Hide 16711 9.REMOVE FAN SHROUD

Hide 10.REMOVE TRANSFER SHIFT LEVER ASSEMBLY

Hide 33530F 11.REMOVE TRANSMISSION SHIFT LEVER ASSEMBLY

C313778C01
1.333,0.635 1.5,0.219 1.5,0.219 1.75,0.219 true 1.875,0.135 2.188,0.333 0.313,0.198 10 false *a
*a Cloth or Equivalent
V100135

Down
V100136

Counterclockwise


a.

Cover the shift lever cap with a cloth or equivalent.


b.

While pressing down on the shift lever cap, turn it counterclockwise to remove the transmission shift lever assembly.


c.

Pull out the transmission shift lever assembly.


Hide 36409C 12.REMOVE FRONT DRIVE SHIFT VACUUM HOSE

a.

Slide the clamp and disconnect the 2 front drive shift vacuum hoses from the diaphragm cylinder assembly.


Hide 51447C 13.REMOVE TRANSFER CASE PROTECTOR

C312479

a.

Remove the 3 bolts and transfer case protector from the No. 2 frame crossmember sub-assembly.


Hide 37140 16.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 37110 17.REMOVE REAR PROPELLER SHAFT ASSEMBLY

Hide 31470 18.REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY

C312477

a.

Remove the 2 bolts and clutch release cylinder assembly.


Hide 33119 19.REMOVE STIFFENER PLATE LH

a.
C312888

Remove the 4 bolts and stiffener plate LH.


Hide 33118 20.REMOVE STIFFENER PLATE RH

a.
C312889

Remove the 4 bolts and stiffener plate RH.


Hide 21.REMOVE FRONT STABILIZER BRACKET LH

C161532

a.

Remove the 2 bolts and front stabilizer bracket LH.


Hide 22.REMOVE FRONT STABILIZER BRACKET RH

HINT:

Use the same procedures described for the LH side.


Hide 23.SUPPORT MANUAL TRANSMISSION WITH TRANSFER

C160886

a.

Support the manual transmission with a transmission jack.

NOTICE:
·

Make sure the high transmission jack attachment is centered on the safety stand.

·

Secure the part with a rope, attachment, etc.




Hide 51203 24.REMOVE NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY

C312481C02
0,0 0,0 false
V100135

Nut
V100136

bolt


a.

Remove the 8 bolts.


b.

Remove the 2 nuts and No. 2 frame crossmember sub-assembly.


Hide 12371 25.REMOVE REAR ENGINE MOUNTING INSULATOR

C312486

a.

Remove the 4 bolts and rear engine mounting insulator from the manual transmission.


Hide 26.DISCONNECT WIRE HARNESS

a.

Disconnect the connectors and clamps, and then disconnect the wire harness from the manual transmission.


Hide 27.REMOVE MANUAL TRANSMISSION WITH TRANSFER

a.

Tilt down the manual transmission.


b.
C312484

Support the engine assembly with the jack, wooden block and engine lifter so that it is stable as shown in the illustration.


c.
C312485

Remove the 5 bolts.


d.

Separate and remove the manual transmission with transfer.

NOTICE:

Do not use excess force to pry off the manual transmission.



Hide 28.REMOVE WIRE HARNESS CLAMP BRACKET

a.

Remove the bolt and wire harness clamp bracket.


Hide 31204 29.REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY

Hide 31230 30.REMOVE CLUTCH RELEASE BEARING ASSEMBLY

Hide 31126 31.REMOVE CLUTCH RELEASE FORK BOOT

Hide 31236B 32.REMOVE RELEASE FORK SUPPORT