Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2022.09
RM25T0E _58 Vehicle Interior _029929 SUPPLEMENTAL RESTRAINT SYSTEMS _0138307 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1805/52  Short in Front Passenger Side Squib Circuit  B1806/52  Open in Front Passenger Side Squib Circuit  B1807/52  Short to GND in Front Passenger Side Squib Circuit  B1808/52  Short to B+ in Front Passenger Side Squib Circuit  


DESCRIPTION

The front passenger side squib circuit consists of the airbag sensor assembly and instrument panel passenger airbag assembly.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front passenger side squib circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1805/52 Short in Front Passenger Side Squib Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal 5 times in the front passenger side squib circuit during the primary check.

·

An instrument panel passenger airbag assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Cowl wire

·

No. 3 instrument panel wire

·

Instrument panel passenger airbag assembly

·

Airbag sensor assembly


B1806/52 Open in Front Passenger Side Squib Circuit One of the following conditions is met:
·

The airbag sensor assembly detects an open circuit signal in the front passenger side squib circuit for 2 seconds.

·

An instrument panel passenger airbag assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Cowl wire

·

No. 3 instrument panel wire

·

Instrument panel passenger airbag assembly

·

Airbag sensor assembly


B1807/52 Short to GND in Front Passenger Side Squib Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to ground signal in the front passenger side squib circuit for 0.5 seconds.

·

An instrument panel passenger airbag assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Cowl wire

·

No. 3 instrument panel wire

·

Instrument panel passenger airbag assembly

·

Airbag sensor assembly


B1808/52 Short to B+ in Front Passenger Side Squib Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to B+ signal in the front passenger side squib circuit for 0.5 seconds.

·

An instrument panel passenger airbag assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Cowl wire

·

No. 3 instrument panel wire

·

Instrument panel passenger airbag assembly

·

Airbag sensor assembly



WIRING DIAGRAM

C253311E33
5.813,0.99 6.042,1.156 0.229,0.167 10 false P+ 5.813,2.208 6.042,2.375 0.229,0.167 10 false P- 3.313,1.198 3.542,1.365 0.229,0.167 10 false P+ 3.313,2.417 3.542,2.583 0.229,0.167 10 false P- 1.354,0.927 1.583,1.094 0.229,0.167 10 false P+ 1.354,2.135 1.583,2.302 0.229,0.167 10 false P- 5.625,0.927 5.75,1.083 0.125,0.156 10 false 4 5.625,2.135 5.75,2.292 0.125,0.156 10 false 3 5.49,2.99 5.875,3.135 0.385,0.146 10 false I51 5.51,3.135 7.073,3.417 1.563,0.281 10 false Airbag Sensor Assembly 3.365,1.99 3.469,2.156 0.104,0.167 10 false 1 1.625,0.896 1.729,1.063 0.104,0.167 10 false 1 3.354,0.802 3.458,0.969 0.104,0.167 10 false 2 1.625,2.125 1.729,2.292 0.104,0.167 10 false 2 3.302,1.01 3.677,1.188 0.375,0.177 10 false IN1 3.313,2.198 3.688,2.375 0.375,0.177 10 false IN1 0.188,3.031 0.375,3.188 0.188,0.156 10 false N1 0.177,3.208 3.01,3.604 2.833,0.396 10 false Instrument Panel Passenger Airbag Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the battery

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag sensor assembly, refer to initialization.*

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

*: w/ VSC



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY
a.
C214261C14
0.458,1.875 0.854,2.146 0.396,0.271 2.042,2.292 2.448,2.51 false 1.51,2.781 1.25,2.979 false 0.479,0.219 0.667,0.396 0.188,0.177 10 false *1 1.958,1.302 2.135,1.479 0.177,0.177 10 false *2 0.719,2.396 0.906,2.573 0.188,0.177 10 false *a 2.292,1.948 2.469,2.125 0.177,0.177 10 false *3 2.5,2.438 3.156,2.708 0.656,0.271 10 false *4 1.083,2.958 1.271,3.135 0.188,0.177 10 false *b 0.563,1.927 0.75,2.094 0.188,0.167 10 false N1 1.396,0.635 1.521,0.813 0.125,0.177 10 false C 1.25,0.635 1.375,0.813 0.125,0.177 10 false D 0.906,0.635 1.031,0.813 0.125,0.177 10 false E 0.656,0.635 0.781,0.813 0.125,0.177 10 false F
*1 Front Passenger Side Squib
*2 Airbag Sensor Assembly
*3 Connector E
*4 SST
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)
*b Color: Orange


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the instrument panel passenger airbag assembly.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (orange connector).

CAUTION:

Never connect the tester to the instrument panel passenger airbag assembly for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output
DTC B1805/52, B1806/52, B1807/52 or B1808/52 is output


HINT:

Codes other than DTC B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.



k.

Turn the ignition switch off.


l.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


m.

Disconnect SST from connector E.



DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output

REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is output

2.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Disconnect the connector from the airbag sensor assembly.


b.
C305108C01
0.417,0.458 0.729,0.615 0.313,0.156 10 false *1 2.469,1.75 2.781,1.906 0.313,0.156 10 false *2 0.573,0.958 0.885,1.115 0.313,0.156 10 false F 0.823,0.969 1.135,1.125 0.313,0.156 10 false E 1.188,0.958 1.5,1.115 0.313,0.156 10 false D 1.354,0.958 1.667,1.115 0.313,0.156 10 false C 1.719,0.958 2.031,1.115 0.313,0.156 10 false B 2.188,0.677 2.5,0.833 0.313,0.156 10 false A
*1 Front Passenger Side Squib
*2 Airbag Sensor Assembly


Check that the connectors (on the airbag sensor assembly side and instrument panel passenger airbag assembly side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT
a.
C214262C12
0.458,1.875 0.854,2.146 0.396,0.271 1.854,2.719 2.094,2.854 false 1.635,2.083 1.219,2.458 false 1.729,2.073 2.073,2.448 false 0.563,0.219 0.75,0.396 0.188,0.177 10 false *1 2.177,1.333 2.354,1.51 0.177,0.177 10 false *2 1.583,1.51 1.771,1.688 0.188,0.177 10 false *a 2.146,1.792 2.323,1.969 0.177,0.177 10 false *3 2.125,2.833 2.313,3.01 0.188,0.177 10 false *b 0.563,1.938 0.75,2.104 0.188,0.167 10 false N1 2.208,0.396 2.333,0.573 0.125,0.177 10 false A 1.469,0.625 1.594,0.802 0.125,0.177 10 false C 1.844,0.625 1.969,0.802 0.125,0.177 10 false B 1.354,0.625 1.479,0.802 0.125,0.177 10 false D 0.99,0.625 1.115,0.802 0.125,0.177 10 false E 0.76,0.625 0.885,0.802 0.125,0.177 10 false F 1.094,2.469 1.385,2.615 0.292,0.146 10 false P+ 2.042,2.479 2.302,2.625 0.26,0.146 10 false P-
*1 Front Passenger Side Squib
*2 Airbag Sensor Assembly
*3 Connector E
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)
*b Color: Orange


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N1-1 (P+) - Body ground Ignition switch ON Below 1 V
N1-2 (P-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N1-1 (P+) - N1-2 (P-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N1-1 (P+) - N1-2 (P-) Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N1-1 (P+) - Body ground Always 1 MΩ or higher
N1-2 (P-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

5.CHECK COWL WIRE
4.CHECK DTC
a.
C212512C01
0.583,0.646 0.896,0.802 0.313,0.156 10 false *1 2.281,1.729 2.594,1.885 0.313,0.156 10 false *2 0.74,1.156 1.052,1.313 0.313,0.156 10 false F 0.906,1.156 1.219,1.313 0.313,0.156 10 false E 1.26,1.146 1.573,1.302 0.313,0.156 10 false D 1.406,1.146 1.719,1.302 0.313,0.156 10 false C 2,0.833 2.313,0.99 0.313,0.156 10 false A
*1 Front Passenger Side Squib
*2 Airbag Sensor Assembly


Connect the connectors to the instrument panel passenger airbag assembly and airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Body Electrical > SRS Airbag > Clear DTCs
50002 63

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR


e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 63
Result:
Proceed to
DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output
DTC B1805/52, B1806/52, B1807/52 or B1808/52 is output


HINT:

Codes other than DTC B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.




DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is output

5.CHECK COWL WIRE
a.
C315274C01
0.125,1.917 0.458,2.083 0.333,0.167 0.917,3.031 1.083,3.031 1.083,3.031 1.396,2.708 false 2.49,3.094 2.302,3.094 2.302,3.094 1.781,2.729 false 0.396,0.281 0.708,0.438 0.313,0.156 10 false *1 2.5,1.396 2.813,1.552 0.313,0.156 10 false *2 0.896,0.25 1.208,0.406 0.313,0.156 10 false *3 1.458,0.24 1.771,0.396 0.313,0.156 10 false *4 2.438,2.115 2.75,2.271 0.313,0.156 10 false *5 1.667,0.74 1.823,0.896 0.156,0.156 10 false B 1.448,1.521 1.76,1.677 0.313,0.156 10 false *a 2.146,0.438 2.302,0.594 0.156,0.156 10 false A 1.323,0.729 1.5,0.896 0.177,0.167 10 false C 1.104,0.729 1.281,0.958 0.177,0.229 10 false D 0.781,0.74 0.958,0.969 0.177,0.229 10 false E 0.583,0.719 0.76,0.948 0.177,0.229 10 false F 0.188,1.917 0.5,2.167 0.313,0.25 10 false IN1 2.563,3.021 2.875,3.177 0.313,0.156 10 false P+ 0.698,2.958 1.01,3.115 0.313,0.156 10 false P-
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag Sensor Assembly
*3 No. 3 Instrument Panel Wire
*4 Cowl Wire
*5 Connector C
*a Front view of wire harness connector
(to No. 3 Instrument Panel Wire)


Disconnect the cowl wire connector from the No. 3 instrument panel wire.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
IN1-2 (P+) - Body ground Ignition switch ON Below 1 V
IN1-1 (P-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IN1-2 (P+) - IN1-1 (P-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IN1-2 (P+) - IN1-1 (P-) Always 1 MΩ or higher



j.

Restore the released activation prevention mechanism of connector B to its original condition.


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IN1-2 (P+) - Body ground Always 1 MΩ or higher
IN1-1 (P-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 3 INSTRUMENT PANEL WIRE

NG

REPLACE COWL WIRE