Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
When disconnecting and reconnecting the battery.
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
CAN JUNCTION CONNECTOR
No. 6 CAN JUNCTION CONNECTOR
Connectors that connect to the No. 6 CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the No. 6 CAN junction connector, reconnecting the connectors to non-original positions on the No. 6 CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.
| *1 | No. 6 CAN Junction Connector | - | - |
| *a | Rear view of wire harness connector (to No. 6 CAN Junction Connector) |
- | - |
| No. 6 CAN Junction Connector | Wiring Color | Connect to |
|---|---|---|
| I119-1 (CANH) | G | Combination meter assembly |
| I119-2 (CANL) | W | |
| I120-1 (CANH) | L | DLC3 |
| I120-2 (CANL) | W | |
| I121-1 (CANH) | R | Spiral with sensor cable sub-assembly (steering angle sensor) |
| I121-2 (CANL) | W | |
| I122-1 (CANH) | G | ECM |
| I122-2 (CANL) | W | |
| I123-1 (CANH) | P | Airbag sensor assembly |
| I123-2 (CANL) | W | |
| I124-1 (CANH) | B | Brake actuator assembly (skid control ECU) |
| I124-2 (CANL) | W |
CHECK DLC3
| *a | Front view of DLC3 |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I17-6 (CANH) - I17-14 (CANL) | L - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I17-6 (CANH) - I17-4 (CG) | L - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I17-14 (CANL) - I17-4 (CG) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I17-6 (CANH) - I17-16 (BAT) | L - V | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I17-14 (CANL) - I17-16 (BAT) | W - V | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)
Refer to Terminals of ECU for Vehicle Stability Control System for further details.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TERMINALS OF ECU
| *a | Front view of wire harness connector (to Brake Actuator Assembly [Skid Control ECU]) |
Disconnect the brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A42-22 (CANH) - A42-10 (CANL) | B - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A42-22 (CANH) - A42-25 (GND1) | B - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A42-10 (CANL) - A42-25 (GND1) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A42-22 (CANH) - A42-38 (+BS) | B - R | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A42-10 (CANL) - A42-38 (+BS) | W - R | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK ECM
Refer to Terminals of ECU for SFI System (for 1GR-FE) or ECD System (for 1VD-FTV) for further details.
for 1VD-FTV: Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>TERMINALS OF ECM
for 1VD-FTV (w/o EGR System): Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR System)>TERMINALS OF ECM
for 1VD-FTV (w/ DPF): Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>TERMINALS OF ECM
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM
Disconnect the ECM connectors.
| *a | Front view of wire harness connector (to ECM) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I84-41 (CANH) - I84-49 (CANL) | G - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I84-41 (CANH) - C39-81 (E1) | G - BR | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I84-49 (CANL) - C39-81 (E1) | W - BR | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I84-41 (CANH) - I84-20 (BATT) | G - P | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I84-49 (CANL) - I84-20 (BATT) | W - P | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK COMBINATION METER ASSEMBLY
Refer to Terminals of ECU for Meter / Gauge System for further details.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU
| *a | Front view of wire harness connector (to Combination Meter Assembly) |
Disconnect the combination meter assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| L26-13 (CANH) - L26-14 (CANL) | G - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| L26-13 (CANH) - L25-15 (ES) | G - BR | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| L26-14 (CANL) - L25-15 (ES) | W - BR | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| L26-13 (CANH) - L25-26 (B) | G - R | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L26-14 (CANL) - L25-26 (B) | W - R | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK AIRBAG SENSOR ASSEMBLY
Refer to Terminals of ECU for Airbag System for further details.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU
| *a | Rear view of wire harness connector (to Airbag Sensor Assembly) |
| *b | Front view of DLC3 |
Disconnect the airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| I51-13 (CANH) - I51-22 (CANL) | P - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I51-13 (CANH) - I51-25 (E1) | P - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I51-22 (CANL) - I51-25 (E1) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I51-13 (CANH) - I17-16 (BAT) | P - V | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I51-22 (CANL) - I17-16 (BAT) | W - V | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)
| *a | Rear view of wire harness connector (to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor]) |
Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| L47-4 (CANH) - L47-3 (CANL) | P - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| L47-4 (CANH) - L47-2 (ESS) | P - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| L47-3 (CANL) - L47-2 (ESS) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| L47-4 (CANH) - L47-6 (BAT) | P - B | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| L47-3 (CANL) - L47-6 (BAT) | W - B | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |