Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD with VSC) › from 2022.09
RM25T0E _57 Power Source / Network _057931 NETWORKING _0306321 CAN COMMUNICATION SYSTEM(for LHD with VSC) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with VSC)  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Either condition is met:
·

"ECM (Engine)" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "ECM Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of ECM

·

ECM ground circuit

·

ECM CAN main wire or connector

·

ECM



WIRING DIAGRAM

for 1VD-FTV


C373834E01
0.292,1.438 2.354,1.708 2.063,0.271 10 false No. 6 CAN Junction Connector 5.625,0.396 6.24,0.594 0.615,0.198 10 false CANH 5.615,1.188 6.229,1.385 0.615,0.198 10 false CANL 5.604,1.948 6.219,2.146 0.615,0.198 10 false BATT 5.594,2.49 6.208,2.688 0.615,0.198 10 false +B 5.604,3.479 6.219,3.677 0.615,0.198 10 false MREL 5.594,4.01 6.208,4.208 0.615,0.198 10 false IGSW 5.604,4.521 6.219,4.719 0.615,0.198 10 false E01 5.604,5.01 6.219,5.208 0.615,0.198 10 false E02 5.594,5.49 6.208,5.688 0.615,0.198 10 false E1 5.604,5.958 6.219,6.156 0.615,0.198 10 false EC 3.865,2.083 4.625,2.313 0.76,0.229 10 false EFI MAIN 4.042,4.146 4.656,4.344 0.615,0.198 10 false IGN 5.25,0.531 5.865,0.729 0.615,0.198 10 false I84 5.26,1.063 5.875,1.26 0.615,0.198 10 false I84 5.25,1.938 5.865,2.135 0.615,0.198 10 false I84 5.25,2.479 5.865,2.677 0.615,0.198 10 false I84 5.26,3.458 5.875,3.656 0.615,0.198 10 false I84 5.26,4 5.875,4.198 0.615,0.198 10 false I84 5.271,5.948 5.885,6.146 0.615,0.198 10 false I84 5.24,4.51 5.854,4.708 0.615,0.198 10 false C39 5.24,4.99 5.854,5.188 0.615,0.198 10 false C39 5.229,5.469 5.844,5.667 0.615,0.198 10 false C39 5.26,0.333 5.875,0.531 0.615,0.198 10 false 41 5.26,0.865 5.875,1.063 0.615,0.198 10 false 49 5.26,1.75 5.875,1.948 0.615,0.198 10 false 20 5.292,2.271 5.906,2.469 0.615,0.198 10 false 2 5.271,3.26 5.885,3.458 0.615,0.198 10 false 44 5.271,3.802 5.885,4 0.615,0.198 10 false 28 5.292,4.323 5.906,4.521 0.615,0.198 10 false 22 5.281,4.792 5.896,4.99 0.615,0.198 10 false 21 5.281,5.281 5.896,5.479 0.615,0.198 10 false 81 5.292,5.76 5.906,5.958 0.615,0.198 10 false 32 0.24,1.26 0.854,1.458 0.615,0.198 10 false I122 1.729,1.927 3.708,2.198 1.979,0.271 10 false from Battery 1.458,2.448 3.438,2.719 1.979,0.271 10 false from MAIN Relay 1.49,3.438 3.469,3.708 1.979,0.271 10 false to MAIN 2 Relay 1.313,4 3.292,4.271 1.979,0.271 10 false from Ignition Switch 5.823,6.417 6.438,6.615 0.615,0.198 10 false ECM 1.542,0.969 2.156,1.167 0.615,0.198 10 false 2 1.552,0.458 2.167,0.656 0.615,0.198 10 false 1


for 1GR-FE


C334614E16
5.271,1.063 5.604,1.292 0.333,0.229 10 false I84 5.292,0.833 5.573,1.031 0.281,0.198 10 false 41 5.646,0.969 6.135,1.156 0.49,0.188 10 false CANH 5.271,1.646 5.604,1.844 0.333,0.198 10 false I84 5.292,1.438 5.563,1.635 0.271,0.198 10 false 49 5.646,1.792 6.24,2.01 0.594,0.219 10 false CANL 5.26,2.479 5.635,2.698 0.375,0.219 10 false I84 5.292,2.271 5.563,2.479 0.271,0.208 10 false 20 5.646,2.479 6.208,2.719 0.563,0.24 10 false BATT 5.271,3.417 5.604,3.646 0.333,0.229 10 false I84 5.333,3.219 5.583,3.438 0.25,0.219 10 false 2 5.646,3.417 6.229,3.719 0.583,0.302 10 false +B 5.271,3.865 5.635,4.063 0.365,0.198 10 false I84 5.333,3.667 5.615,3.896 0.281,0.229 10 false 1 5.292,4.083 5.646,4.292 0.354,0.208 10 false 44 5.646,3.865 6.146,4.083 0.5,0.219 10 false +B2 5.271,2.969 5.646,3.177 0.375,0.208 10 false I84 5.292,2.75 5.594,2.927 0.302,0.177 10 false 28 5.646,2.958 6.229,3.208 0.583,0.25 10 false IGSW 5.271,4.292 5.677,4.521 0.406,0.229 10 false I84 5.646,4.292 6.219,4.542 0.573,0.25 10 false MREL 5.271,4.75 5.646,4.99 0.375,0.24 10 false I84 5.292,4.542 5.604,4.74 0.313,0.198 10 false 32 5.646,4.75 6.208,5.021 0.563,0.271 10 false EC 5.24,5.24 5.615,5.438 0.375,0.198 10 false C39 5.292,5.031 5.521,5.208 0.229,0.177 10 false 81 5.646,5.229 6.229,5.448 0.583,0.219 10 false E1 5.24,5.729 5.646,5.958 0.406,0.229 10 false C39 5.292,5.521 5.573,5.719 0.281,0.198 10 false 20 5.646,5.719 6.333,6.021 0.688,0.302 10 false ME01 5.24,6.229 5.635,6.438 0.396,0.208 10 false C39 5.292,6.01 5.583,6.208 0.292,0.198 10 false 21 5.646,6.219 6.271,6.469 0.625,0.25 10 false E02 5.24,6.719 5.635,6.958 0.396,0.24 10 false C39 5.292,6.5 5.573,6.719 0.281,0.219 10 false 22 5.646,6.719 6.26,6.938 0.615,0.219 10 false E01 5.24,7.208 5.615,7.438 0.375,0.229 10 false C39 5.281,7 5.573,7.188 0.292,0.188 10 false 23 5.646,7.198 6.229,7.458 0.583,0.26 10 false E04 5.24,7.698 5.625,7.896 0.385,0.198 10 false C39 5.292,7.479 5.563,7.667 0.271,0.188 10 false 46 5.646,7.688 6.198,7.885 0.552,0.198 10 false E05 5.854,8.292 6.354,8.51 0.5,0.219 10 false ECM 1.646,1.531 1.885,1.771 0.24,0.24 10 false 2 0.5,2.021 1.052,2.219 0.552,0.198 10 false I122 0.5,2.156 2.573,2.469 2.073,0.313 10 false No. 6 CAN Junction Connector 1.646,0.948 1.885,1.177 0.24,0.229 10 false 1 1.844,2.469 3.479,2.729 1.635,0.26 10 false from Battery 1.458,2.938 3.156,3.24 1.698,0.302 10 false from Ignition Switch 4.042,2.333 5.427,2.615 1.385,0.281 10 false EFI 4.031,2.813 5.333,3.073 1.302,0.26 10 false IGN 1.479,4.281 3.323,4.563 1.844,0.281 10 false to EFI MAIN Relay 1.406,3.406 3.25,3.688 1.844,0.281 10 false from EFI MAIN Relay


CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with VSC)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

When disconnecting and reconnecting the battery.

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Drive the vehicle for 3 seconds at a speed of 15 km/h (9 mph) or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with VSC)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (ECM CAN MAIN WIRE)
a.
C363469C04
1.573,0.292 2.031,0.521 0.458,0.229 2.427,1.354 2.656,1.167 2.656,1.167 2.823,1.167 true 2.427,1.458 2.625,1.938 2.625,1.938 2.792,1.938 true 0.135,0.094 0.448,0.25 0.313,0.156 10 false *a 2.875,1.042 3.385,1.292 0.51,0.25 10 false CANH 2.833,1.823 3.344,2.073 0.51,0.25 10 false CANL 1.719,0.333 2.229,0.583 0.51,0.25 10 false I84
*a Front view of wire harness connector
(to ECM)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I84-41 (CANH) - I84-49 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE ECM CAN MAIN WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal.


b.

for 1VD-FTV:

i.

Disconnect the ECM connector.

C234869C19
1.99,0.49 2.458,0.76 0.469,0.271 4.594,0.5 5.063,0.771 0.469,0.271 1.542,0.708 1.76,0.708 1.76,0.708 1.958,1.219 true 5.5,1.219 5.781,0.396 5.781,0.396 6,0.396 true 5.813,2.313 5.51,2.313 5.51,2.313 5.208,1.646 true 1.115,1.01 1.333,1.01 1.333,1.01 1.865,1.385 true 1.896,2.5 2.115,2.5 2.115,2.5 2.344,1.719 true 1.229,2.198 1.448,2.198 1.448,2.198 1.938,1.677 true 5.583,1.208 5.854,0.604 5.854,0.604 6.073,0.604 true 3,0.667 2.75,0.667 2.75,0.667 2.604,1.375 true 0.125,0.073 0.417,0.25 0.292,0.177 10 false *a 6.135,0.5 6.677,0.802 0.542,0.302 10 false E01 5.875,2.198 6.74,2.365 0.865,0.167 10 false E1 4.698,0.521 5.031,0.698 0.333,0.177 10 false C39 0.76,0.917 1.188,1.083 0.427,0.167 10 false BATT 1.281,0.604 1.708,0.771 0.427,0.167 10 false +B 1.469,2.396 1.896,2.563 0.427,0.167 10 false MREL 0.958,2.094 1.385,2.26 0.427,0.167 10 false EC 6.083,0.323 6.625,0.625 0.542,0.302 10 false E02 2.146,0.542 2.479,0.719 0.333,0.177 10 false I84 3.073,0.583 3.5,0.75 0.427,0.167 10 false IGSW
*a Front view of wire harness connector
(to ECM)
- -



ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I84-20 (BATT) - Body ground Always 11 to 14 V
I84-2 (+B) - Body ground Battery positive (+) voltage applied to terminal I84-44 (MREL) 11 to 14 V
I84-28 (IGSW) - Body ground Ignition switch ON 11 to 14 V



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I84-32 (EC) - Body ground Always Below 1 Ω
C39-22 (E01) - Body ground Always Below 1 Ω
C39-21 (E02) - Body ground Always Below 1 Ω
C39-81 (E1) - Body ground Always Below 1 Ω




c.

for 1GR-FE:

i.

Disconnect the ECM connector.

C234869C18
1.99,0.458 2.458,0.729 0.469,0.271 4.594,0.5 5.063,0.771 0.469,0.271 1.438,0.688 1.656,0.688 1.656,0.688 1.854,1.198 true 5.688,1.208 6.25,0.823 6.25,0.823 6.469,0.823 true 5.813,2.313 5.51,2.313 5.51,2.313 5.208,1.646 true 1.115,1.01 1.333,1.01 1.333,1.01 1.865,1.385 true 1.896,2.5 2.115,2.5 2.115,2.5 2.344,1.719 true 1.229,2.198 1.448,2.198 1.448,2.198 1.938,1.677 true 5.583,1.208 5.854,0.604 5.854,0.604 6.073,0.604 true 1.479,0.417 1.698,0.417 1.698,0.417 1.979,1.208 true 3.01,0.354 2.844,0.354 2.844,0.354 2.594,1.354 true 5.396,1.188 5.5,0.167 5.5,0.167 5.667,0.167 true 5.479,1.188 5.802,0.385 5.802,0.385 6.021,0.385 true 6.448,2 6.146,2 6.146,2 5.677,1.417 true 2.146,0.51 2.438,0.688 0.292,0.177 10 false I84 0.125,0.073 0.417,0.25 0.292,0.177 10 false *a 6.135,0.5 6.677,0.802 0.542,0.302 10 false E01 5.875,2.198 6.74,2.365 0.865,0.167 10 false E1 4.708,0.552 5.042,0.729 0.333,0.177 10 false C39 0.76,0.917 1.188,1.083 0.427,0.167 10 false BATT 1.146,0.604 1.573,0.771 0.427,0.167 10 false +B2 1.469,2.396 1.896,2.563 0.427,0.167 10 false MREL 0.958,2.094 1.385,2.26 0.427,0.167 10 false EC 6.531,0.729 7.073,1.031 0.542,0.302 10 false E04 1.26,0.333 1.688,0.5 0.427,0.167 10 false +B 3.063,0.271 3.49,0.438 0.427,0.167 10 false IGSW 5.698,0.083 6.24,0.385 0.542,0.302 10 false ME01 6.052,0.302 6.594,0.604 0.542,0.302 10 false E02 6.5,1.927 7.042,2.229 0.542,0.302 10 false E05
*a Front view of wire harness connector
(to ECM)
- -



ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I84-20 (BATT) - Body ground Always 11 to 14 V
I84-2 (+B) - Body ground Battery positive (+) voltage applied to terminal I84-44 (MREL) 11 to 14 V
I84-1 (+B2) - Body ground Battery positive (+) voltage applied to terminal I84-44 (MREL) 11 to 14 V
I84-28 (IGSW) - Body ground Ignition switch ON 11 to 14 V



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I84-32 (EC) - Body ground Always Below 1 Ω
C39-20 (ME01) - Body ground Always Below 1 Ω
C39-21 (E02) - Body ground Always Below 1 Ω
C39-22 (E01) - Body ground Always Below 1 Ω
C39-23 (E04) - Body ground Always Below 1 Ω
C39-46 (E05) - Body ground Always Below 1 Ω
C39-81 (E1) - Body ground Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR