This is the repair procedure for the accelerator pedal position sensor.
This electrical throttle system does not use a throttle cable.
This accelerator pedal position sensor is a non-contact type.
The accelerator pedal position sensor is mounted on the accelerator pedal and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and a malfunction of the accelerator position sensor.
In the accelerator pedal position sensor, the voltage applied to terminals VPA and VPA2 of the ECM changes between 0 V and 5 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for the engine control, and the VPA2 is a signal to indicate the information about the opening angle which is used for detecting malfunctions.
The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the injection volume based on these signals.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2120 | Throttle / Pedal Position Sensor / Switch "D" Circuit | Condition (a) continues for 0.5 seconds or more: (1 trip detection logic) (a) VPA less than 0.4 V and VPA2 greater than 0.97 deg, or VPA greater than 4.8 V |
·
Accelerator pedal position sensor
·
Accelerator pedal
·
Accelerator pedal rod (arm) deformed
·
ECM |
Comes on | DTC stored |
| P2122 | Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input | Condition (a) and (b) continue for 0.5 seconds or more: (1 trip detection logic) (a) VPA less than 0.4 V (b) VPA2 greater than 0.97 deg |
·
Accelerator pedal position sensor
·
Open in VCPA circuit
·
VPA circuit open or ground short
·
Accelerator pedal
·
Accelerator pedal rod (arm) deformed
·
ECM |
Comes on | DTC stored |
| P2123 | Throttle / Pedal Position Sensor / Switch "D" Circuit High Input | Condition (a) continues for 2.0 seconds or more: (1 trip detection logic) (a) VPA greater than 4.8 V |
·
Accelerator pedal position sensor
·
Open in EPA circuit
·
Accelerator pedal
·
Accelerator pedal rod (arm) deformed
·
ECM |
Comes on | DTC stored |
| P2125 | Throttle / Pedal Position Sensor / Switch "E" Circuit | Condition (a) continues for 0.5 seconds or more: (1 trip detection logic) (a) VPA2 less than 1.2 V and VPA greater than 2.7 deg, or VPA2 greater than 4.8 V and VPA greater than 0.4 V but less than 3.45 V |
·
Accelerator pedal position sensor
·
Accelerator pedal
·
Accelerator pedal rod (arm) deformed
·
ECM |
Comes on | DTC stored |
| P2127 | Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input | Condition (a) and (b) continue for 1.2 seconds or more: (1 trip detection logic) (a) VPA2 less than 1.2 V (b) VPA1 greater than 2.7 deg |
·
Accelerator pedal position sensor
·
Open in VCP2 circuit
·
VPA2 circuit open or ground short
·
Accelerator pedal
·
Accelerator pedal rod (arm) deformed
·
ECM |
Comes on | DTC stored |
| P2128 | Throttle / Pedal Position Sensor / Switch "E" Circuit High Input | Condition (a) and (b) continue for 2.0 seconds or more: (1 trip detection logic) (a) VPA2 greater than 4.8 V (b) VPA greater than 0.4 V but less than 3.45 V |
·
Accelerator pedal position sensor
·
Open in EPA2 circuit
·
Accelerator pedal
·
Accelerator pedal rod (arm) deformed
·
ECM |
Comes on | DTC stored |
| P2138 | Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation | Condition (a) or (b) continues for 2.0 seconds or more: (1 trip detection logic) (a) Difference between VPA and VPA2 less than 0.02 V (b) VPA less than 0.4 V and VPA2 less than 1.2 V |
·
VPA and VPA2 circuits are short circuited
·
Accelerator pedal position sensor
·
Accelerator pedal
·
Accelerator pedal rod (arm) deformed
·
ECM |
Comes on | DTC stored |
When DTC P2120, P2122, P2123, P2125, P2127, P2128 or P2138 is detected, check the output voltage of the accelerator pedal position sensor by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Accel Position 1 and Accel Position 2.
| Trouble Area | Accelerator pedal position expressed as voltage output | |||
|---|---|---|---|---|
| Accelerator pedal released | Accelerator pedal depressed | |||
| Accel Position 1 | Accel Position 2 | Accel Position 1 | Accel Position 2 | |
| VC circuit open | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V |
| VPA circuit open or ground short | 0 to 0.2 V | 1.2 to 2.0 V | 0 to 0.2 V | 3.4 to 5.0 V |
| VPA2 circuit open or ground short | 0.5 to 1.1 V | 0 to 0.2 V | 2.9 to 3.6 V | 0 to 0.2 V |
| EPA circuit open | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V | 4.5 to 5.0 V |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P2120 P2122 P2123 P2125 P2127 P2128 P2138 |
Ignition switch ON
·
Accelerator pedal fully released for 3 seconds
·
Accelerator pedal depressed partway for 3 seconds
·
Accelerator pedal fully depressed for 3 seconds |
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
| *1 | Accelerator Pedal |
| *a | Depressed |
| *b | Released |
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.
| Tester Display |
|---|
| Accel Sens. No.1 Volt % |
| Accel Sens. No.2 Volt % |
Read the values.
| Accelerator Pedal | Accel Sens. No. 1 Volt % | Accel Sens. No. 2 Volt % |
|---|---|---|
| Released | 10 to 22% | 24 to 40% |
| Depressed | 52 to 90% | 68 to 99% |
| Proceed to |
| OK |
| NG |
OK
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>CHECK FOR INTERMITTENT PROBLEMS
NG
| *A | for RHD |
| *B | for LHD |
| *a | Front view of wire harness connector (to Accelerator Pedal Position Sensor) |
| *b | Front view of wire harness connector (to ECM) |
Disconnect the accelerator pedal position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I43-1 (VCP2) - A29-56 (VCP2) | Always | Below 1 Ω |
| I43-2 (EPA2) - A29-58 (EPA2) | Always | Below 1 Ω |
| I43-3 (VPA2) - A29-54 (VPA2) | Always | Below 1 Ω |
| I43-4 (VCPA) - A29-55 (VCPA) | Always | Below 1 Ω |
| I43-5 (EPA) - A29-57 (EPA) | Always | Below 1 Ω |
| I43-6 (VPA) - A29-53 (VPA) | Always | Below 1 Ω |
| I43-1 (VCP2) or A29-56 (VCP2) - Body ground | Always | 10 kΩ or higher |
| I43-2 (EPA2) or A29-58 (EPA2) - Body ground | Always | 10 kΩ or higher |
| I43-3 (VPA2) or A29-54 (VPA2) - Body ground | Always | 10 kΩ or higher |
| I43-4 (VCPA) or A29-55 (VCPA) - Body ground | Always | 10 kΩ or higher |
| I43-5 (EPA) or A29-57 (EPA) - Body ground | Always | 10 kΩ or higher |
| I43-6 (VPA) or A29-53 (VPA) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I43-1 (VCP2) - I84-56 (VCP2) | Always | Below 1 Ω |
| I43-2 (EPA2) - I84-58 (EPA2) | Always | Below 1 Ω |
| I43-3 (VPA2) - I84-54 (VPA2) | Always | Below 1 Ω |
| I43-4 (VCPA) - I84-55 (VCPA) | Always | Below 1 Ω |
| I43-5 (EPA) - I84-57 (EPA) | Always | Below 1 Ω |
| I43-6 (VPA) - I84-53 (VPA) | Always | Below 1 Ω |
| I43-1 (VCP2) or I84-56 (VCP2) - Body ground | Always | 10 kΩ or higher |
| I43-2 (EPA2) or I84-58 (EPA2) - Body ground | Always | 10 kΩ or higher |
| I43-3 (VPA2) or I84-54 (VPA2) - Body ground | Always | 10 kΩ or higher |
| I43-4 (VCPA) or I84-55 (VCPA) - Body ground | Always | 10 kΩ or higher |
| I43-5 (EPA) or I84-57 (EPA) - Body ground | Always | 10 kΩ or higher |
| I43-6 (VPA) or I84-53 (VPA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector (to Accelerator Pedal Position Sensor) |
Disconnect the accelerator pedal position sensor.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I43-4 (VCPA) - I43-5 (EPA) | Ignition switch ON | 4.5 to 5.5 V |
| I43-1 (VCP2) - I43-2 (EPA2) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
| OK |
| NG |
OK
NG
Replace the accelerator pedal sensor assembly.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL
| Proceed to |
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTC.
Turn the ignition switch off and leave the vehicle for 30 seconds.
Turn the ignition switch ON.
Fully release the accelerator pedal for 3 seconds or more, then depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
| NEXT |
NEXT