Home › Engine / Hybrid System › 1VD-FTV (FUEL) › FUEL INJECTOR (w/ DPF) › from 2022.09
RM25T0E _51 Engine / Hybrid System _029770 1VD-FTV FUEL _0290474 FUEL INJECTOR(w/ DPF) A

1VD-FTV FUEL  FUEL INJECTOR(w/ DPF)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing an injector (including interchanging injectors between cylinders) or common rail, replace the corresponding injection pipes with new ones.

·

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.



PROCEDURE

Hide 1.CHECK INJECTOR COMPENSATION CODE

a.

Check that the injector compensation code registered in the injector assembly installed on each cylinder matches the one registered in the engine ECM.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION


b.

If the code does not match, follow the procedures below to correct the registration details and recheck the symptom.

i.

Correct the registration details by following the procedures in "Register Injector Compensation Code".

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION


ii.

After correcting the registration details, check if the symptom that occurred when the vehicle was brought in recurs.

HINT:

If it does not occur, the symptom may be caused by errors in the injector compensation code registration.




Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 17940D 5.REMOVE INTERCOOLER ASSEMBLY

Hide 23801L 7.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

Hide 27148B 9.REMOVE CONNECTING WIRE

a.
A267236

Detach the 2 clamps and remove the connecting wire.


Hide 23763 10.REMOVE NO. 3 NOZZLE LEAKAGE PIPE

a.
A267237C01
0.208,0.594 0.521,0.75 0.313,0.156 10 false *a 1.219,0.208 1.417,0.365 0.198,0.156 10 true *b 3.198,0.75 3.385,0.906 0.188,0.156 10 false *a 2.167,0.271 2.365,0.427 0.198,0.156 10 true *b 0.198,1.688 0.396,1.844 0.198,0.156 10 true *b
*a Injector Hollow Screw
*b Bolt


Remove the 2 injector hollow screws, 3 bolts, No. 3 nozzle leakage pipe and 2 gaskets.

NOTICE:
·

When removing the nozzle leakage pipe, place a cushion under the pipe.

·

Be careful not to deform or scratch the union seal surface.

·

After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.




Hide 23761A 11.REMOVE NO. 1 NOZZLE LEAKAGE PIPE

a.
A392185C01
0.813,1.792 0.99,1.948 0.177,0.156 10 true *a 0.094,1.094 0.406,1.25 0.313,0.156 10 false *b 0.406,0.042 0.719,0.198 0.313,0.156 10 false *c 0.104,0.375 0.417,0.531 0.313,0.156 10 false *d 1.688,1.792 1.865,1.948 0.177,0.156 10 true *a 2.385,1.792 2.563,1.948 0.177,0.156 10 true *a 3.073,1.75 3.25,1.906 0.177,0.156 10 true *a
*a Injector Hollow Screw
*b Bolt
*c No. 2 Check Valve
*d Union Bolt


Remove the 4 injector hollow screws and 4 gaskets.


b.

Remove the bolt.


c.

Remove the No. 2 check valve from the fuel tube and No. 1 nozzle leakage pipe.


d.

Remove the union bolt and No. 1 nozzle leakage pipe.

NOTICE:
·

When removing the nozzle leakage pipe, place a cushion under the pipe.

·

Be careful not to deform or scratch the union seal surface.

·

After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.




Hide 12.REMOVE FUEL INJECTOR RH

a.
A271220

Remove the 4 bolts, 4 washers, 4 nozzle holder clamps, 4 nozzle holder seals and 4 fuel injectors.

HINT:

Arrange the fuel injectors, holder clamps, washers and bolts in the correct order.



b.

Remove the O-ring from each fuel injector.


c.

Remove the fuel injector seal from each fuel injector.


d.

Remove the 4 injection nozzle seats from the cylinder head sub-assembly.


Hide 23762B 13.REMOVE NO. 2 NOZZLE LEAKAGE PIPE

a.
A392186C01
0.51,1.604 0.698,1.76 0.188,0.156 10 true *a 2.135,0.656 2.333,0.813 0.198,0.156 10 true *b 1.177,1.604 1.365,1.76 0.188,0.156 10 true *a 2.688,1.583 2.875,1.74 0.188,0.156 10 true *a 2,1.604 2.188,1.76 0.188,0.156 10 true *a 3.104,0.771 3.302,0.927 0.198,0.156 10 true *b
*a Injector Hollow Screw
*b Bolt


Remove the 4 injector hollow screws and 4 gaskets.


b.

Remove the 2 bolts and No. 2 nozzle leakage pipe.

NOTICE:
·

When removing the nozzle leakage pipe, place a cushion under the pipe.

·

Be careful not to deform or scratch the union seal surface.

·

After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.




Hide 14.REMOVE FUEL INJECTOR LH

a.
A271221

Remove the 4 bolts, 4 washers, 4 nozzle holder clamps, 4 nozzle holder seals and 4 fuel injectors.

HINT:

Arrange the fuel injectors, holder clamps, washers and bolts in the correct order.



b.

Remove the O-ring from each fuel injector.


c.

Remove the fuel injector seal from each fuel injector.


d.

Remove the 4 injection nozzle seats from the cylinder head sub-assembly.