Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT (for RHD)
RM37H0E _58 Vehicle Interior _095300 HEATING / AIR CONDITIONING _0452690 AIR CONDITIONING UNIT(for RHD) A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E454995N13
6.5,0.271 6.75,0.271 false 1.083,2.417 1.083,2.083 false 3.833,4.115 3.75,3.781 3.75,3.781 3.583,3.781 false 6.521,0.656 6.771,0.656 false 0.927,0.958 0.76,0.625 0.76,0.625 0.594,0.625 false 2.75,2.594 2.75,2.26 false 2.01,5.156 2.01,4.823 false 5.906,4.083 6.24,4.083 false 4.375,5.417 3.927,5.417 3.927,5.417 3.927,5.167 false 1.5,0.25 1.781,0.604 0.281,0.354 10 false x 6 6.031,0.115 6.521,0.458 0.49,0.344 18 false 1, 5 0.406,0.49 0.688,0.844 0.281,0.354 18 false 2 2.708,2.625 2.99,2.979 0.281,0.354 18 false 3 1.031,2.479 1.313,2.833 0.281,0.354 18 false 4 1.958,5.198 2.24,5.552 0.281,0.354 18 false 6 3.385,3.646 3.667,4 0.281,0.354 18 false 7 6.365,3.948 6.646,4.302 0.281,0.354 18 false 8 3.281,1.448 3.563,1.802 0.281,0.354 10 false x 6 1.813,1.323 2.094,1.677 0.281,0.354 10 false x 6 6.323,0.521 6.604,0.875 0.281,0.354 18 false 9 3.031,5.396 3.458,5.698 0.427,0.302 10 false x 3 2.688,5.531 3.167,5.729 0.479,0.198 10 false x 12 4.052,5.01 4.479,5.313 0.427,0.302 10 false x 7 6.063,4.896 6.49,5.198 0.427,0.302 10 false x 11 4.417,5.323 4.729,5.521 0.313,0.198 10 false ●★

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CAUTIONS FOR COOLANT (TOYOTA GENUINE FC STACK COOLANT (Pre-mixed)) - (Click here) - -
2 RADIATOR COVER PLATE 53291B - - -
3 UPPER RADIATOR SUPPORT SEAL 53292A - - -
4 LOWER RADIATOR AIR DEFLECTOR 53295 - - -
5 REFRIGERANT FROM REFRIGERATION SYSTEM - (Click here) - -
6 FRONT COMPARTMENT UNDER COVER 51441N - - -
7 FRONT LOWER SUSPENSION MEMBER PROTECTOR 51219 - - -
8 FRONT COMPARTMEMT UNDER COVER ASSEMBLY 51420A - - -
9 DRAIN COOLANT (TOYOTA GENUINE FC STACK COOLANT (Pre-mixed)) - - (Click here) -

● Non-reusable part ★ Precoated part

E456986N02
5.917,2.083 6.167,1.75 6.167,1.75 6.333,1.75 false 5.677,1.229 5.844,1.229 5.844,1.229 5.927,0.979 false 6,0.344 6.333,0.344 false 3.75,0.583 4,0.333 4,0.333 4.167,0.333 false 1.688,3.219 1.688,3.469 false 2.906,1.188 3.156,1.188 3.156,1.188 3.323,1.438 false 2.99,2.615 3.323,2.615 false 1.417,0.75 1.667,0.5 1.667,0.5 1.833,0.5 false 1.24,1.583 1.24,1.167 false 0.5,1.583 0.5,0.917 0.5,0.917 0.75,0.917 false 0.833,3.5 0.833,3.167 0.833,3.167 1.083,3.167 false 1.583,2.583 1.917,2.333 1.917,2.333 2.167,2.333 false 1.927,2.833 1.927,2.333 false 6.385,0.188 6.938,0.542 0.552,0.354 18 false 12 6.417,1.625 6.969,1.979 0.552,0.354 18 false 10 5.365,1.063 5.917,1.417 0.552,0.354 18 false 11 4.219,0.167 4.771,0.521 0.552,0.354 18 false 13 0.875,3.5 1.427,3.854 0.552,0.354 18 false 15 2.583,1.052 3.135,1.406 0.552,0.354 18 false 14 1.76,3.49 2.313,3.844 0.552,0.354 18 false 16 3.385,2.49 3.938,2.844 0.552,0.354 18 false 17 1.26,1.583 1.813,1.938 0.552,0.354 18 false 19 1.906,0.385 2.458,0.74 0.552,0.354 18 false 20 0.531,1.583 1.083,1.938 0.552,0.354 18 false 18 6.021,0.385 6.573,0.74 0.552,0.354 10 false x 2 2.25,2.271 2.521,2.521 0.271,0.25 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

10 FRONT WIPER MOTOR AND LINK - - - -
11 COWL VENTILATOR SPLASH SHIELD LH 55752A - - -
12 HOLE PLUG - - - -
13 FLOOR UNDER WIRE 821H1 - - -
14 FC JUNCTION CABLE G9A2C - - -
15 SUCTION HOSE SUB-ASSEMBLY A 88704A (Click here) - -
16 NO. 1 LIQUID TUBE 88G16M (Click here) - -
17 COOLER PIPE GROMMET 88897K - - -
18 WATER HOSE SUB-ASSEMBLY E 87209E (Click here) - -
19 WATER HOSE SUB-ASSEMBLY C 87209C (Click here) - -
20 GROMMET 88898D - - -

● Non-reusable part - -

E454997N14
1.24,2.385 1.656,2.385 false 5.729,2.188 6.063,2.188 false 6.125,2.052 6.677,2.406 0.552,0.354 18 false 22 0.906,2.26 1.458,2.615 0.552,0.354 18 false 21

Procedure Part Name Code
Z101186

Z101188

Z101187

21 FRONT SEAT ASSEMBLY LH - - - -
22 FRONT SEAT ASSEMBLY RH - - - -

E458113N03
1.313,0.083 3,0.656 1.688,0.573 5.052,5.417 5.302,5.417 false 3.25,1.521 3.333,1.104 3.333,1.104 3.5,1.104 false 5.688,1.917 5.885,1.917 false 2.594,5.531 2.813,5.531 2.813,5.531 2.948,5.396 false 1.854,3.667 1.635,3.667 false 4.875,4.198 5.031,4.396 5.031,4.396 5.281,4.396 false 2.271,0.292 2.604,0.292 false 1.25,0.938 0.979,0.333 0.979,0.333 0.771,0.333 false 3.333,2.656 3.5,2.656 false 6.229,5.365 6.229,5.115 false 4.417,5.26 4.583,5.26 4.583,5.26 4.667,5.104 false 5.76,5.063 5.927,5.063 5.927,5.063 6.01,4.802 false 6.479,3.656 6.479,3.375 false 1.281,5.615 0.385,5.615 0.385,5.615 0.385,4.844 true 6.844,1.177 6.844,0.271 6.844,0.271 6.063,0.271 true 6.563,1.021 6.563,0.281 true 0.667,5.594 0.667,4.99 true 2.635,2.375 2.969,2.375 false 6.26,2.313 6.49,2.313 false 6.281,0.865 6.281,0.281 true 2.458,4.583 2.167,4.583 false 0.75,3.385 0.594,3.385 false 4.594,1.615 4.792,1.615 false 0.948,5.604 0.948,5.135 true 0.438,0.198 0.99,0.552 0.552,0.354 18 false 23 3.583,0.969 4.135,1.323 0.552,0.354 18 false 25 2.635,0.146 3.188,0.5 0.552,0.354 18 false 24 5.885,1.781 6.438,2.135 0.552,0.354 18 false 33 6.365,3.677 6.917,4.031 0.552,0.354 18 false 30 2.344,2.25 2.896,2.604 0.552,0.354 18 false 34 2.281,5.385 2.833,5.74 0.552,0.354 18 false 26 1.896,3.531 2.448,3.885 0.552,0.354 18 false 29 3.063,2.521 3.615,2.875 0.552,0.354 18 false 35 4.135,5.115 4.688,5.469 0.552,0.354 18 false 36 5.479,4.948 6.031,5.302 0.552,0.354 18 false 36 5.365,5.302 6,5.583 0.635,0.281 18 false 37 6.135,5.396 6.771,5.677 0.635,0.281 18 false 37 5.625,4.229 6.26,4.51 0.635,0.281 18 false 39 1.344,0.104 1.719,0.344 0.375,0.24 12 false *A 6.385,4.604 6.698,4.802 0.313,0.198 10 false x2 3.927,2.406 4.24,2.604 0.313,0.198 10 false x2 5,4.948 5.313,5.146 0.313,0.198 10 false x2 4.698,5.115 5.01,5.313 0.313,0.198 10 false x2 6.063,4.792 6.375,4.99 0.313,0.198 10 false x2 1.604,5.469 2.24,5.75 0.635,0.281 18 false 38 5.76,0.135 6.396,0.417 0.635,0.281 18 false 38 4.313,1.479 4.865,1.833 0.552,0.354 18 false 31 6.771,2.208 7.146,2.542 0.375,0.333 18 false 32 0.323,3.25 0.875,3.604 0.552,0.354 18 false 27 2.76,4.458 3.313,4.813 0.552,0.354 18 false 28

Procedure Part Name Code
Z101186

Z101188

Z101187

23 INSTRUMENT PANEL SAFETY PAD - - - -
24 METER MIRROR SUB-ASSEMBLY 83108 - - -
25 STEERING COLUMN ASSEMBLY 45250 - - -
26 REAR DOOR SCUFF PLATE INSIDE LH 67918F - - -
27 FRONT DOOR OPENING TRIM WEATHERSTRIP LH 62312B (Click here) - -
28 REAR DOOR OPENING TRIM WEATHERSTRIP LH 62332A (Click here) - -
29 LOWER CENTER PILLAR GARNISH LH 62414A - - -
30 REAR DOOR SCUFF PLATE INSIDE RH 67917F - - -
31 FRONT DOOR OPENING TRIM WEATHERSTRIP RH 62311B (Click here) - -
32 REAR DOOR OPENING TRIM WEATHERSTRIP RH 62331A (Click here) - -
33 LOWER CENTER PILLAR GARNISH RH 62413A - - -
34 ACCELERATOR PEDAL PAD 78118 - - -
35 ACCELERATOR PEDAL ASSEMBLY 78010F (Click here) - -
36 AIR DUCT PLUG 87217B (Click here) - -
37 REAR NO. 5 AIR DUCT 87212J - - -
38 NO. 2 FLOOR CARPET HOOK 58521C (Click here) - -
39 FRONT FLOOR FRONT CARPET ASSEMBLY 58510C (Click here) - -

*A w/ Headup Display - -

E454999N07
4.24,1.229 4.24,0.979 false 2.281,2.625 2.781,2.625 false 6.344,3.906 6.344,3.573 false 4.667,2.927 4.667,2.594 false 2.5,4.167 2.917,4.167 false 1.344,2.125 1.344,1.792 false 6.24,3.948 6.792,4.302 0.552,0.354 18 false 40 4.563,2.969 5.115,3.323 0.552,0.354 18 false 41 4.146,1.292 4.698,1.646 0.552,0.354 18 false 42 2.198,4.052 2.75,4.406 0.552,0.354 18 false 43 1.969,2.5 2.521,2.854 0.552,0.354 18 false 44 1.229,2.167 1.781,2.521 0.552,0.354 18 false 45

Procedure Part Name Code
Z101186

Z101188

Z101187

40 REAR NO. 2 AIR DUCT 87212F - - -
41 REAR NO. 1 AIR DUCT 87212 - - -
42 FRONT FLOOR MAT RH 58511H - - -
43 REAR NO. 4 AIR DUCT 87212H - - -
44 REAR NO. 3 AIR DUCT 87212G - - -
45 FRONT FLOOR MAT LH 58512B - - -

E458074N02
5.583,2.833 5.583,2.583 false 0.948,3.885 0.948,3.635 false 2.542,2.688 2.792,2.688 false 1.406,3.042 1.594,3.042 false 2,5.031 2,4.698 false 4.302,2.531 4.552,2.531 false 3.854,3.615 4.104,3.615 false 4.302,4.844 4.552,4.844 false 1.417,0.531 1.833,0.531 false 4.135,1.167 4.469,1.167 false 2.438,2.177 2.271,2.177 2.271,2.177 2.24,1.969 false 5.979,1.708 5.979,1.458 false 5.927,0.958 5.76,0.958 5.76,0.958 5.677,0.625 false 5.844,3.521 6.26,3.521 false 4.813,4.729 5.365,5.083 0.552,0.354 18 false 46 0.833,3.958 1.385,4.313 0.552,0.354 18 false 52 2.26,2.531 2.813,2.885 0.552,0.354 18 false 47 1.073,2.896 1.625,3.25 0.552,0.354 18 false 48 1.865,5.052 2.417,5.406 0.552,0.354 18 false 49 4.604,2.375 5.156,2.729 0.552,0.354 18 false 50 4.469,3.438 5.021,3.792 0.552,0.354 18 false 51 4.51,1.01 5.063,1.365 0.552,0.354 18 false 53 1.094,0.375 1.646,0.729 0.552,0.354 18 false 54 2.76,2.052 3.313,2.406 0.552,0.354 18 false 55 5.875,1.74 6.427,2.094 0.552,0.354 18 false 56 6,0.833 6.552,1.188 0.552,0.354 18 false 57 5.479,2.865 6.031,3.219 0.552,0.354 18 false 58 6.583,3.396 7.135,3.75 0.552,0.354 18 false 59 2.51,1.177 2.76,1.344 0.25,0.167 10 false x 3 4.333,1.521 4.583,1.688 0.25,0.167 10 false x 2 1.833,3.646 2.083,3.813 0.25,0.167 10 false x 2 6.729,1.635 6.979,1.802 0.25,0.167 10 false x 2 6.344,2.594 6.594,2.76 0.25,0.167 10 false x 3 4.583,2.969 4.833,3.135 0.25,0.167 10 false x 2 6.469,3.979 6.719,4.146 0.25,0.167 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

46 NO. 3 AIR DUCT SUB-ASSEMBLY 87201F (Click here) - -
47 EV CONTROL ECU WITH EV CONTROL ECU BRACKET - - - -
48 PASSENGER SIDE JUNCTION BLOCK ASSEMBLY 82730D (Click here) - -
49 FRONT COMPARTMENT WIRE MAIN 82111C - - -
50 SHIFT CONTROL ECU 894C1 - - -
51 NO. 1 SEMICONDUCTOR POWER INTEGRATION ECU 82644A (Click here) - -
52 WIRING HARNESS CLAMP BRACKET 82715 - - -
53 STEREO COMPONENT EQUALIZER ASSEMBLY 86240A - - -
54 NO. 5 HEATER TO REGISTER DUCT 55847B (Click here) - -
55 NO. 2 SIDE DEFROSTER NOZZLE DUCT 55972C (Click here) - -
56 NAVIGATION ECU ASSEMBLY WITH BRACKET - - - -
57 LOWER DEFROSTER NOZZLE ASSEMBLY 55990B - - -
58 TELEMATICS TRANSCEIVER WITH BRACKET - - - -
59 NO. 4 HEATER TO REGISTER DUCT 55846A (Click here) - -

E455001N03
2.083,1.01 1.833,0.427 1.833,0.427 1.667,0.427 false 2.167,3.896 2.25,3.479 2.25,3.479 2.417,3.479 false 0.906,4.5 1.323,4.5 false 3.333,3.5 3.25,3.083 3.25,3.083 3.083,3.083 false 3.927,5.26 4.26,5.26 false 5.594,0.677 5.927,0.677 false 5.615,2.083 5.948,2.083 false 5.771,4.646 6,4.646 false 4.938,3.115 5.188,3.115 false 2.49,3.323 3.042,3.677 0.552,0.354 18 false 60 0.604,4.354 1.156,4.708 0.552,0.354 18 false 61 2.771,2.917 3.323,3.271 0.552,0.354 18 false 62 5.281,0.531 5.833,0.885 0.552,0.354 18 false 63 6.281,1.938 6.833,2.292 0.552,0.354 18 false 64 5.458,4.5 6.01,4.854 0.552,0.354 18 false 65 4.594,2.969 5.146,3.323 0.552,0.354 18 false 66 3.646,5.104 4.198,5.458 0.552,0.354 18 false 67 1.365,0.281 1.917,0.635 0.552,0.354 18 false 68 6.552,1.042 7.104,1.396 0.552,0.354 10 false x 3 5.802,1.563 6.354,1.917 0.552,0.354 10 false x 2 0.448,4.042 1,4.396 0.552,0.354 10 false x2 4.208,3.635 4.76,3.99 0.552,0.354 10 false x 2 2.656,4.385 3.208,4.74 0.552,0.354 10 false x 2 5.75,3.635 6.302,3.99 0.552,0.354 10 false x 2 3.052,0.344 3.604,0.698 0.552,0.354 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

60 NO. 1 INSTRUMENT PANEL SHIFT MOUNTING BRACKET 55381D - - -
61 NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY 55307C - - -
62 NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY 55306A - - -
63 NO. 3 HEATER TO REGISTER DUCT 55845A (Click here) - -
64 NO. 1 HEATER TO REGISTER DUCT 55843A (Click here) - -
65 NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY 55308B - - -
66 DRIVER SIDE JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU - (Click here) - -
67 AIR CONDITIONING AMPLIFIER ASSEMBLY WITH HEATER BRACKET - - - -
68 INSTRUMENT PANEL WIRE 82141 - - -

E455002N03
5.833,2.417 6,2.167 6,2.167 6.167,2.167 false 5.833,4.823 6.167,4.823 false 2.563,5.583 2.948,5.583 false 2.302,4.75 2.635,4.75 false 5.052,4.479 5.385,4.479 false 6.604,4.667 7.063,5.063 0.458,0.396 18 false 71 2.24,5.427 2.99,5.75 0.75,0.323 18 false 71 6.521,1.917 6.958,2.313 0.438,0.396 18 false 72 6.646,2.698 6.958,2.896 0.313,0.198 10 false x 4 6.479,4.729 6.771,4.938 0.292,0.208 10 false ● 2.125,5.5 2.417,5.708 0.292,0.208 10 false ● 1.406,0.302 1.729,0.469 0.323,0.167 10 true x 2 4.74,4.354 5.417,4.75 0.677,0.396 18 false 69 2.01,4.604 2.688,5 0.677,0.396 18 false 70

Procedure Part Name Code
Z101186

Z101188

Z101187

69 NO. 4 COOLER UNIT DRAIN HOSE 88539N - - -
70 NO. 3 COOLER UNIT DRAIN HOSE 88539E - - -
71 COOLER UNIT DRAIN HOSE GROMMET 88539G (Click here) - -
72 INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY - (Click here) - -

● Non-reusable part - -

E455003N03
4.823,3.823 5.052,3.823 5.052,3.823 5.344,3.177 false 4.5,3.688 5.052,4.042 0.552,0.354 18 false 73 6.542,2.604 7.094,2.958 0.552,0.354 10 false x 3

Procedure Part Name Code
Z101186

Z101188

Z101187

73 AIR CONDITIONER UNIT ASSEMBLY - - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the air conditioner unit assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Steering sensor (Including removal and installation) Steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

No. 1 air conditioner radiator damper servo sub-assembly

·

No. 2 air conditioner radiator damper servo sub-assembly

·

No. 3 air conditioner radiator damper servo sub-assembly

·

No. 4 air conditioner radiator damper servo sub-assembly

·

No. 5 air conditioner radiator damper servo sub-assembly

·

No. 6 air conditioner radiator damper servo sub-assembly


Servo motor initialization DTC output (Click here)

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

When removing the air conditioning radiator damper servo sub-assembly, reinstallation is easier to perform if the following conditions are set before disconnecting the negative (-) battery terminal.

Item Condition
Air vent damper position Face
Set temperature Max cool



PROCEDURE

Hide 1. CAUTIONS FOR COOLANT (TOYOTA GENUINE FC STACK COOLANT (Pre-mixed))

Hide 53291B 2.REMOVE RADIATOR COVER PLATE

Hide 53292A 3.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 53295 4.REMOVE LOWER RADIATOR AIR DEFLECTOR

Hide 5.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 51441N 6.REMOVE FRONT COMPARTMENT UNDER COVER

Hide 51219 7.REMOVE FRONT LOWER SUSPENSION MEMBER PROTECTOR

Hide 51420A 8.REMOVE FRONT COMPARTMEMT UNDER COVER ASSEMBLY

Hide 9.DRAIN COOLANT (TOYOTA GENUINE FC STACK COOLANT (Pre-mixed))

Hide 10.REMOVE FRONT WIPER MOTOR AND LINK

Hide 55752A 11.REMOVE COWL VENTILATOR SPLASH SHIELD LH

a.
E455004


Hide 12.REMOVE HOLE PLUG

a.
E455005


Hide 821H1 13.DISCONNECT FLOOR UNDER WIRE

a.
E456091


Hide G9A2C 14.DISCONNECT FC JUNCTION CABLE

a.
E456092


Hide 88704A 15.DISCONNECT SUCTION HOSE SUB-ASSEMBLY A

a.
E455006C01
4.021,0.146 4.354,0.49 0.333,0.344 18 true ii 2.563,2.219 3.115,2.573 0.552,0.354 18 false iii 0.521,0.083 0.729,0.406 0.208,0.323 18 true i
V113147

Remove in this Direction - -


i.

Remove the bolt.


ii.

Rotate the 1-point tightening plate and disconnect the suction hose sub-assembly A.


iii.

Remove the O-ring from the suction pipe sub-assembly A.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.




Hide 88G16M 16.DISCONNECT NO. 1 LIQUID TUBE

a.
E455007N01
0.646,0.083 0.896,0.333 0.25,0.25 18 true i 4.563,0.115 4.802,0.427 0.24,0.313 18 true ii

i.

Disconnect the No. 1 liquid tube.


ii.

Remove the O-ring from the No. 1 liquid tube.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.




Hide 88897K 17.REMOVE COOLER PIPE GROMMET

a.
E455008


Hide 87209E 18.DISCONNECT WATER HOSE SUB-ASSEMBLY E

a.
E455009N01
0.406,0.052 0.688,0.406 0.281,0.354 18 false i

i.

Using pliers, grip the claws of the clip and slide the clip to disconnect the water hose sub-assembly E.

NOTICE:
·

Do not apply excessive force to the water hose sub-assembly E.

·

Prepare a drain pan or cloth in case the coolant leaks.





Hide 87209C 19.DISCONNECT WATER HOSE SUB-ASSEMBLY C

a.
E455010N01
0.375,0 0.656,0.354 0.281,0.354 18 false i

i.

Using pliers, grip the claws of the clip and slide the clip to disconnect the water hose sub-assembly C.

NOTICE:
·

Do not apply excessive force to the water hose sub-assembly C.

·

Prepare a drain pan or cloth in case the coolant leaks.





Hide 88898D 20.REMOVE GROMMET

a.
E455011


Hide 21.REMOVE FRONT SEAT ASSEMBLY LH

Hide 22.REMOVE FRONT SEAT ASSEMBLY RH

a.

Use the same procedure described for the LH side.


Hide 23.REMOVE INSTRUMENT PANEL SAFETY PAD

Hide 83108 24.REMOVE METER MIRROR SUB-ASSEMBLY (w/ Headup Display)

Hide 45250 25.REMOVE STEERING COLUMN ASSEMBLY

Hide 67918F 26.REMOVE REAR DOOR SCUFF PLATE INSIDE LH

Hide 62312B 27.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Z101186

HINT:

Remove the rear side of the front door opening trim weatherstrip LH so that the lower center pillar garnish LH can be removed.

(Click here)



Hide 62332A 28.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

Z101186

HINT:

Remove the front side of the rear door opening trim weatherstrip LH so that the lower center pillar garnish LH can be removed.

(Click here)



Hide 62414A 29.REMOVE LOWER CENTER PILLAR GARNISH LH

Hide 67917F 30.REMOVE REAR DOOR SCUFF PLATE INSIDE RH

a.

Use the same procedure described for the LH side.


Hide 62311B 31.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

a.

Use the same procedure described for the LH side.


Hide 62331A 32.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

a.

Use the same procedure described for the LH side.


Hide 62413A 33.REMOVE LOWER CENTER PILLAR GARNISH RH

a.

Use the same procedure described for the LH side.


Hide 78010F 35.REMOVE ACCELERATOR PEDAL ASSEMBLY

Z101186

Click here(Click here)

Hide 87217B 36.REMOVE AIR DUCT PLUG

a.
E455012N02
0.406,0.042 0.688,0.396 0.281,0.354 18 false i

i.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and remove the air duct plug.



b.

Use the same procedure for the other side.


Hide 87212J 37.REMOVE REAR NO. 5 AIR DUCT

a.
E455013C01
0,0 0,0 false
V113147

Remove in this Direction - -



b.

Use the same procedure for the other side.


Hide 58521C 38.REMOVE NO. 2 FLOOR CARPET HOOK

a.
E455014N02
0.365,0.063 0.646,0.417 0.281,0.354 18 false i

i.

Using a clip remover with its tip wrapped with protective tape, detach the clamp and remove the 3 No. 2 floor hooks.



b.

Use the same procedure for the other side.


Hide 58510C 39.REMOVE FRONT FLOOR FRONT CARPET ASSEMBLY

a.
E455015C01
5.469,0.083 5.667,0.333 0.198,0.25 18 true i 4.302,0.917 4.5,1.167 0.198,0.25 18 true ii 4.635,1.333 4.833,1.583 0.198,0.25 18 true iii 2.802,0.583 3,0.833 0.198,0.25 18 true iv
V113147

Pull Out
V113148

Fold Up
V100155

Fastener - -


i.

Using a clip remover, remove the clip.


ii.

Detach the claw.


iii.

Detach the 3 fasteners.


iv.

Remove some of the front floor front carpet assembly in the order shown in the illustration until the rear floor mat RH can be removed.



b.
E455016C01
5.552,0.198 5.719,0.469 0.167,0.271 18 true i 0.604,0.219 0.823,0.49 0.219,0.271 18 true iii 2.625,1.5 2.813,1.771 0.188,0.271 18 true ii 4.094,0.75 4.313,1.021 0.219,0.271 18 true iv
V113147

Pull Out
V113148

Fold Up
V100155

Fastener - -


i.

Using a clip remover, remove the clip.


ii.

Detach the claw.


iii.

Detach the fastener.


iv.

Remove some of the front floor front carpet assembly in the order shown in the illustration until the rear floor mat LH can be removed.



Hide 87212F 40.REMOVE REAR NO. 2 AIR DUCT

a.
E455017C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 87212 41.REMOVE REAR NO. 1 AIR DUCT

a.
E455019C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 58511H 42.REMOVE FRONT FLOOR MAT RH

a.
E455020


Hide 87212H 43.REMOVE REAR NO. 4 AIR DUCT

a.
E455018C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 87212G 44.REMOVE REAR NO. 3 AIR DUCT

a.
E455021C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 58512B 45.REMOVE FRONT FLOOR MAT LH

a.
E455022


Hide 87201F 46.REMOVE NO. 3 AIR DUCT SUB-ASSEMBLY

a.
E455023C01
0.438,0.042 0.719,0.396 0.281,0.354 18 false i
V113147

Remove in this Direction - -


i.

Using a clip remover, remove the clip and No. 3 air duct sub-assembly.



Hide 47.REMOVE EV CONTROL ECU WITH EV CONTROL ECU BRACKET

Hide 82730D 48.REMOVE PASSENGER SIDE JUNCTION BLOCK ASSEMBLY

a.
E455024C01
1.344,0.26 1.51,0.531 0.167,0.271 18 true i 3.833,0.167 4.115,0.521 0.281,0.354 18 false ii 1.969,3.813 2.25,4.167 0.281,0.354 18 false iii
V113147

Remove in this Direction
V100135

Connector
V100136

Lever Connector
V100137

Nut


i.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw.


ii.

Disconnect the 2 lever connectors and 2 connectors.


iii.

Remove the 2 nuts and passenger side junction block assembly.



b.
E455025C01
0.875,0.438 1.042,0.708 0.167,0.271 18 true i 4.021,0.198 4.188,0.469 0.167,0.271 18 true ii 3.354,3.583 3.604,3.844 0.25,0.26 18 true iii
V113147

Remove in this Direction
V100135

Connector
V100136

Lever Connector


i.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw.


ii.

Disconnect the 2 lever connectors and connector.


iii.

Detach the clamp and claw.



Hide 82111C 49.DISCONNECT FRONT COMPARTMENT WIRE MAIN

a.
E455027


Hide 82644A 51.REMOVE NO. 1 SEMICONDUCTOR POWER INTEGRATION ECU

Z101186

Click here(Click here)

Hide 82715 52.REMOVE WIRING HARNESS CLAMP BRACKET

a.
E455026


Hide 86240A 53.REMOVE STEREO COMPONENT EQUALIZER ASSEMBLY

Hide 55847B 54.REMOVE NO. 5 HEATER TO REGISTER DUCT

a.
E455028N01
0.385,0.063 0.667,0.417 0.281,0.354 18 false i

i.

Using a clip remover, remove the 3 clips and No. 5 heater to register duct.



Hide 55972C 55.REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT

a.
E455029N01
2.052,1.146 2.333,1.5 0.281,0.354 18 false i 4.896,0.5 5.073,0.781 0.177,0.281 18 true ii 3.052,0.271 3.229,0.552 0.177,0.281 18 true ii

i.

Using a clip remover, remove the clip.


ii.

Detach the clamp and claw and remove the No. 2 side defroster nozzle duct.



Hide 56.REMOVE NAVIGATION ECU ASSEMBLY WITH BRACKET

Hide 55990B 57.REMOVE LOWER DEFROSTER NOZZLE ASSEMBLY

a.
E455031


Hide 58.REMOVE TELEMATICS TRANSCEIVER WITH BRACKET

Hide 55846A 59.REMOVE NO. 4 HEATER TO REGISTER DUCT

a.
E455030N01
0.365,0.042 0.646,0.396 0.281,0.354 18 false i

i.

Using a clip remover, remove the 2 clips and No. 4 heater to register duct.



Hide 55381D 60.REMOVE NO. 1 INSTRUMENT PANEL SHIFT MOUNTING BRACKET

a.
E455032C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)



Hide 55307C 61.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
E455033C01
0,0 0,0 false
V100135

Bolt
V100136

Nut
V100137

Screw - -



Hide 55306A 62.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
E455034C01
0,0 0,0 false
V100135

Bolt
V100136

Nut
V100137

Screw - -



Hide 55845A 63.REMOVE NO. 3 HEATER TO REGISTER DUCT

a.
E455035N01
0.406,0.083 0.688,0.438 0.281,0.354 18 false i

i.

Using a clip remover, remove the 3 clips and No. 3 heater to register duct.



Hide 55843A 64.REMOVE NO. 1 HEATER TO REGISTER DUCT

a.
E455036C01
2.281,0.104 2.5,0.344 0.219,0.24 18 true i 4.479,0.01 4.698,0.25 0.219,0.24 18 true i 2.552,1.385 2.771,1.625 0.219,0.24 18 true ii
V100135

Clip
V100136

Screw


i.

Using a clip remover, remove the 2 clips.


ii.

Remove the screw and No. 1 heater to register duct.



Hide 55308B 65.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

a.
E455037C01
0,0 0,0 false
V100135

Bolt
V100136

Nut



Hide 66.REMOVE DRIVER SIDE JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU

Z101186

Click here(Click here)

Hide 67.REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY WITH HEATER BRACKET

Hide 82141 68.DISCONNECT INSTRUMENT PANEL WIRE

HINT:

The illustration is an example, so the details may differ.


a.
E455038


b.
E455039


Hide 88539N 69.REMOVE NO. 4 COOLER UNIT DRAIN HOSE

a.
E455040


Hide 88539E 70.REMOVE NO. 3 COOLER UNIT DRAIN HOSE

a.
E455041


Hide 88539G 71.REMOVE COOLER UNIT DRAIN HOSE GROMMET

Z101186

NOTICE:

After removing the cooler unit drain hose grommet, replace it with a new one to prevent water from entering.



a.
E456987C02
0.073,0.104 0.333,0.333 0.26,0.229 12 true *A 3.667,0.104 3.927,0.333 0.26,0.229 12 true *B
*A for Driver Side *B for Passenger Side



Hide 72.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY

Z101186

NOTICE:
·

Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.

·

Do not hold the air conditioning harness assembly. Otherwise, static electricity from the technician may damage the air conditioning harness assembly.

·

Do not hold the heater core or pipe of the heater radiator unit sub-assembly. Otherwise, the pipe may detach, the clamp may be damaged, or the crimped areas of the heater core and pipe of the heater radiator unit sub-assembly may be damaged, causing coolant to leak.

·

Do not hold the air conditioning radiator damper servo sub-assembly, blower damper servo sub-assembly or link. Otherwise, the servo motor may become misaligned, causing abnormal operation noise, temperature control defects, or air leaks due to sealing defects in the doors.

·

Do not hold the door. Doing so may cause air leaks due to closing defects resulting from excessive opening/closing. Also, keep the door free from oil and grease.




a.
E455042C05
0.375,3.083 0.552,3.365 0.177,0.281 18 true ii 2.281,0.167 2.438,0.458 0.156,0.292 18 true i 6.625,3.01 6.802,3.292 0.177,0.281 18 true ii 6.625,2.208 6.802,2.49 0.177,0.281 18 true ii 0.417,2.208 0.594,2.49 0.177,0.281 18 true ii 3.656,4.198 3.833,4.479 0.177,0.281 18 true ii 0.885,4.229 1.073,4.51 0.188,0.281 18 true ii 2.281,1.198 2.51,1.375 0.229,0.177 10 true *a 5.781,1.281 6.01,1.458 0.229,0.177 10 true *a
*a Bolt (A) - -
V100135

Bolt
V100136

Nut


i.

Using a universal socket wrench 12 mm, remove the 2 bolts (A).


ii.

Remove the 6 bolts and nut.



b.
E455043C01
2.698,2.167 2.917,2.427 0.219,0.26 18 true iii 5.167,0.438 5.323,0.708 0.156,0.271 18 true i 0.542,0.417 0.698,0.688 0.156,0.271 18 true i 2.615,0.156 2.813,0.417 0.198,0.26 18 true ii
V113147

Remove in this Direction - -


i.

Remove the instrument panel reinforcement assembly with air conditioning unit assembly from the guide as shown in the illustration.


ii.

Detach the clamp and disconnect the connector.


iii.

Remove the instrument panel reinforcement assembly with air conditioning unit assembly from the vehicle.



Hide 73.REMOVE AIR CONDITIONER UNIT ASSEMBLY

a.
E455045