Home › Vehicle Exterior › WINDOW / GLASS › QUARTER WINDOW GLASS
RM37H0E _59 Vehicle Exterior _095305 WINDOW / GLASS _0448203 QUARTER WINDOW GLASS A

WINDOW / GLASS  QUARTER WINDOW GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
E459258N01
3.271,0.979 3.271,1.333 false 6.542,0.167 6.875,0.167 false 5.146,2.333 5.146,2.448 5.146,2.448 5.563,2.448 false 1.833,3.365 1.833,3.094 false 6.083,0.042 6.698,0.333 0.615,0.292 18 false 1, 3 5.958,2.323 6.24,2.677 0.281,0.354 18 false 2 3.219,1.344 3.5,1.698 0.281,0.354 18 false 5 5.844,2.344 6,2.542 0.156,0.198 10 false ● 1.781,3.396 2.063,3.75 0.281,0.354 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CLEAN QUARTER WINDOW ASSEMBLY LH 62720A (Click here) - -
2 INSTALL QUARTER WINDOW ASSEMBLY LH 62720A (Click here) - -
3 CHECK FOR LEAK AND REPAIR - (Click here) - -
4 PACKAGE TRAY TRIM PANEL ASSEMBLY 64330 - - -
5 CURTAIN SHIELD AIRBAG ASSEMBLY LH 62180A - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

NOTICE:
·

Be sure to use the quarter window assembly adhesive (specialized for high-rigidity specification vehicles) as the adhesive for replacing the quarter window assembly.

·

Be sure to use the quarter window assembly adhesive (specialized for high-rigidity specification vehicles) as the adhesive for adjusting the quarter window assembly.



HINT:
·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 62720A 1.CLEAN QUARTER WINDOW ASSEMBLY LH

a.
B585857N01
2.396,0.073 2.677,0.427 0.281,0.354 18 false i

i.

Using non-residue solvent, clean the outer edge of the clean quarter window assembly LH.

NOTICE:

Be sure to clean the quarter window assembly LH even it is new.




Hide 62720A 2.INSTALL QUARTER WINDOW ASSEMBLY LH

a.
E459243C01
0.583,0.198 1.958,0.552 1.375,0.354 18 false i 4.021,1.542 4.177,1.74 0.156,0.198 10 false a
V100155

Adhesive - -


i.

Follow the procedure below to clean the installation surface of the vehicle body.

1. If the adhesive left on the installation surface of the vehicle body is significantly uneven, smooth it out using a utility knife, etc.

Standard Dimension:
Area Dimension
a 1.0 to 3.0 mm (0.0394 to 0.1181 in.)


NOTICE:

Make sure to leave some adhesive.


2. Using non-residue solvent, clean the installation surface of the vehicle body.

3. Install the suction cups to the quarter window assembly LH.

4. Apply primer to the exposed sections of the body surface on the vehicle side (where no adhesive remains).

NOTICE:
·

When applying the primer, take care of the panel joints and spot welds.

·

Do not apply to the adhesive.

·

Do not apply too much primer.





b.
E444309C01
3.51,2.292 3.635,2.458 0.125,0.167 10 true B 1.958,1.5 2.115,1.698 0.156,0.198 10 false A 1.917,2.25 2.031,2.396 0.115,0.146 10 true C 3.156,2.135 3.281,2.292 0.125,0.156 10 true B 1.917,2.646 2.031,2.813 0.115,0.167 10 true C 5.573,0.219 6.031,0.417 0.458,0.198 10 false A-A 5.583,1.385 6.042,1.583 0.458,0.198 10 false B-B 5.594,2.615 6.052,2.813 0.458,0.198 10 false C-C 0.365,0.479 0.677,0.677 0.313,0.198 10 false *a 2.073,1.823 2.167,1.99 0.094,0.167 10 true A 0.417,0.073 0.698,0.427 0.281,0.354 18 false i
*a Backside - -
V100155

Glass Primer - -


i.

Using a brush, apply primer to the entire perimeter of the adhesion area of the quarter window assembly LH as shown in the illustration.

NOTICE:

Do not apply too much glass primer.




c.
B582006C02
3.188,0.271 3.063,0.344 false 4.427,0.406 4.854,0.156 true 3.24,0.177 3.552,0.333 0.313,0.156 10 false *b 0.479,0.104 0.781,0.406 0.302,0.302 18 false i 2.417,0.479 2.729,0.635 0.313,0.156 10 false a 2.615,0.906 2.927,1.063 0.313,0.156 10 false b 2.969,0.729 3.281,0.885 0.313,0.156 10 false b 3.167,1.323 3.479,1.479 0.313,0.156 10 false a 4.896,0.083 5.208,0.281 0.313,0.198 10 false *a
*a Sealant Gun *b Nozzle


i.

Cut off the tip of the cartridge nozzle as shown in the illustration, and set the adhesive in the sealant gun.

Standard Dimension:
Area Dimension
a 8.0 to 11.0 mm (0.315 to 0.433 in.)
b 6.0 to 9.0 mm (0.236 to 0.354 in.)




d.
E444310C01
0.156,0.438 0.469,0.594 0.313,0.156 10 false *a 0.385,0.042 0.583,0.313 0.198,0.271 18 false i 1.927,2.01 2.083,2.167 0.156,0.156 10 false A 2.052,2.354 2.167,2.51 0.115,0.156 10 true A 3.49,2.792 3.646,2.948 0.156,0.156 10 false B 3.156,2.646 3.271,2.802 0.115,0.156 10 true B 1.917,3.156 2.073,3.313 0.156,0.156 10 false C 1.927,2.75 2.042,2.906 0.115,0.156 10 true C 4.833,0.615 5.167,0.771 0.333,0.156 10 false A-A 4.823,1.854 5.156,2.01 0.333,0.156 10 false B-B 4.844,2.896 5.177,3.052 0.333,0.156 10 false C-C 5.938,0.75 6.094,0.906 0.156,0.156 10 false a 5.635,1.844 5.792,2 0.156,0.156 10 false b 5.688,3 5.844,3.156 0.156,0.156 10 false c
*a Backside - -
V100155

Adhesive - -


i.

Apply a bead of adhesive as shown in the illustration.

NOTICE:

After the primer dries (in approximately 3 minutes), apply the adhesive.


Standard Dimension:
Area Dimension
a 5.0 mm (0.1969 in.)
b 5.0 mm (0.1969 in.)
c 5.0 mm (0.1969 in.)




e.
E444311N01
0.406,0.073 0.688,0.427 0.281,0.354 18 false i

i.

Follow the procedure below to perform quarter window assembly LH installation.

1. Using the suction cups, align the matchmarks and install the quarter window assembly LH.

NOTICE:
·

After the body side primer dries (in approximately 3 minutes), install the quarter window assembly LH.

·

From inside the cabin, check that the clips are attached.



2. Gently push the front surface of the quarter window assembly LH from outside of vehicle to fully contact with the adhesive.

HINT:

Pushing force: 98 N (10 kgf) or higher


3. Remove any excess adhesive or apply as necessary.

NOTICE:

Apply adhesive up to the edge of the quarter window assembly LH.


4. Remove any excess adhesive before it hardens.

5. Using protective tape, hold the quarter window assembly LH in place until the adhesive hardens.

NOTICE:

Follow the instructions for each adhesive manufacturer or the corresponding owner's manual for the minimum amount of time necessary for drying and prior to driving the vehicle after applying adhesive.




Hide 3.CHECK FOR LEAK AND REPAIR

a.
B630199N01
0.396,0.031 0.677,0.385 0.281,0.354 18 false i

i.

Follow the procedure below to check for water leak and repair.

1. Remove the protective tape and adhesive tape.

2. After the adhesive has hardened, apply water from outside the vehicle and check for leaks from in the cabin.

3. If water leaks into the cabin, seal any leaks with adhesive after the water has dried.



Hide 64330 4.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY

Hide 62180A 5.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH