Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT DIMMER SWITCH
RM37H0E _59 Vehicle Exterior _093353 LIGHTING (EXT) _0448247 HEADLIGHT DIMMER SWITCH A

LIGHTING (EXT)  HEADLIGHT DIMMER SWITCH  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
E463007N02
1.656,2.198 1.24,2.198 false 2.563,1.458 2.563,1.125 false 4.156,3.042 4.917,3.042 false 6.417,0.333 6.76,0.333 false 5.365,2.896 5.646,3.25 0.281,0.354 18 false 2 2.521,1.469 2.802,1.823 0.281,0.354 18 false 3 1.031,2.073 1.313,2.427 0.281,0.354 18 false 4 1.344,2.427 1.625,2.781 0.281,0.354 10 false x 2 4.885,2.438 5.167,2.792 0.281,0.354 10 false x 3 5.813,0.198 6.792,0.604 0.979,0.406 18 false 1(*A)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM - (Click here) - -
2 LOWER STEERING COLUMN COVER 45287 (Click here) - -
3 UPPER STEERING COLUMN COVER 45286B - - -
4 TURN SIGNAL SWITCH 84329 (Click here) - -

*A for Power Tilt and Power Telescopic Steering Column - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the turn signal switch removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Steering sensor (Including removal and installation) Steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM (for Power Tilt and Power Telescopic Steering Column)

Z101186

Click here(Click here)

Hide 45287 2.REMOVE LOWER STEERING COLUMN COVER

Z101186

Click here(Click here)

Hide 45286B 3.REMOVE UPPER STEERING COLUMN COVER

Hide 84329 4.REMOVE TURN SIGNAL SWITCH

a.
E463008C01
0.75,0.146 1.031,0.5 0.281,0.354 18 true i 4.042,0.167 4.323,0.521 0.281,0.354 18 true ii 4.906,1.354 5.156,1.625 0.25,0.271 18 true iii
V113147

Remove in this Direction - -


i.

Remove the 2 screws.


ii.

Turn the steering wheel assembly 90° to the right from the straight condition.


iii.

Using a screwdriver with its tip wrapped with protective tape, detach the claw and remove the turn signal switch as shown in the illustration.

NOTICE:

Do not forcibly pry the claw, or it may become damaged.