Home › Vehicle Interior › HEATING / AIR CONDITIONING › REFRIGERANT (for HFC-134a(R134a))
RM37H0E _58 Vehicle Interior _095300 HEATING / AIR CONDITIONING _0448328 REFRIGERANT(for HFC-134a(R134a)) G

HEATING / AIR CONDITIONING  REFRIGERANT(for HFC-134a(R134a))  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

HINT:
·

Steps 2 to 9 specify the procedure to determine the cause of a refrigerant leak.

·

Step 10 specifies the procedure to check if there is a clog in the expansion valve.



PROCEDURE

Hide 1.INSPECT REFRIGERANT PRESSURE WITH MANIFOLD GAUGE SET

HINT:

The following examples show the readings of a manifold gauge set and the corresponding air conditioning system problems.


Pre-procedure1

a.

Remove the upper radiator support seal.

HINT:

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL



b.

Remove the radiator cover plate.

HINT:

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL



c.

Remove the lower radiator air deflector.

HINT:

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL



Procedure1

a.

Read the manifold gauge pressure when the following conditions are met:

·

Doors are fully open.

·

The power switch is on (READY).

·

The A/C switch is on.

·

The temperature is set to max cool.

·

The blower speed is set to high.

·

Temperature at the air inlet with recirculate selected is 30 to 35°C (86 to 95°F).


i.
E268307

Normally functioning air conditioning system

Gauge Reading
Pressure Side Refrigerant Volume
Low 150 to 250 kPa (1.5 to 2.5 kgf/cm2, 22 to 36 psi)
High 1370 to 1570 kPa (14.0 to 16.0 kgf/cm2, 199 to 228 psi)


ii.

Abnormally functioning air conditioning system

1.
E225742C10
0.906,1.698 1.188,1.927 0.281,0.229 10 false *a 2.375,1.698 2.656,1.927 0.281,0.229 10 false *b
*a LO
*b HI


During operation, pressure on low pressure side cycles between normal and vacuum

Symptom Air conditioning system periodically cools and then fails to cool
Probable Cause Moisture in air conditioning system freezes at expansion valve orifice, causing refrigerant to temporarily stop circulating
After system stops and warms up again, ice melts and normal operation is temporarily restored
Diagnosis Cooler dryer (integrated into condenser tank) saturated with moisture
Moisture in air conditioning system is freezing at expansion valve orifice and blocking circulation of refrigerant
Corrective Actions Replace cooler dryer
Remove moisture by repeatedly evacuating air from air conditioning system
Recharge air conditioning system with proper amount of new or purified refrigerant

HINT:

For the example above, moisture is present in the air conditioning system.


2.
E225743C10
0.958,1.708 1.146,1.896 0.188,0.188 10 *a 2.354,1.708 2.542,1.896 0.188,0.188 10 *b
*a LO
*b HI


Pressure is low on both low and high pressure sides

Symptom Air conditioning system does not cool effectively
Insufficient cooling performance
Probable Cause Refrigerant leaks from air conditioning system
Diagnosis Insufficient refrigerant
Refrigerant leaking
Corrective Actions Check for refrigerant leaks and repair if necessary
Recharge air conditioning system with proper amount of new or purified refrigerant
If gauges indicate pressure of close to 0, then it is necessary to evacuate air conditioning system after repairing leaks

HINT:

For the example above, there is insufficient refrigerant.


3.
E225744C10
0.95,1.724 1.209,1.924 0.259,0.2 10 *a 2.342,1.724 2.601,1.924 0.259,0.2 10 *b
*a LO
*b HI


Pressure is low on both low and high pressure sides

Symptom Air conditioning system does not cool effectively
Frost exists on pipe from condenser to evaporator unit
Probable Cause Refrigerant flow is obstructed by dirt inside pipes of condenser core
Diagnosis Condenser is clogged
Corrective Actions Replace condenser

HINT:

For the example above, there is poor circulation of refrigerant.


4.
E225745C10
0.965,1.747 1.159,1.933 0.195,0.186 10 *a 2.408,1.747 2.603,1.933 0.195,0.186 10 *b
*a LO
*b HI


Vacuum is indicated on low pressure side and very low pressure is indicated on high pressure side

Symptom Air conditioning system does not cool effectively (system may cool occasionally)
Frost or condensation is seen on piping on both sides of receiver/dryer or expansion valve
Probable Cause Refrigerant flow is obstructed by moisture or dirt in air conditioning system
Expansion valve is stuck closed
Diagnosis Refrigerant does not circulate
Corrective Actions Replace expansion valve
Replace condenser
Evacuate air conditioning system and recharge with proper amount of new or purified refrigerant

HINT:

For the example above, the refrigerant does not circulate.


5.
E225746C10
0.948,1.75 1.146,1.958 0.198,0.208 10 *a 2.354,1.75 2.552,1.958 0.198,0.208 10 *b
*a LO
*b HI


Pressure is too high on both low and high pressure sides

Symptom Air conditioning system does not cool effectively
Probable Cause Unable to provide sufficient performance due to excessive amount of refrigerant
Cooling effectiveness of condenser is insufficient
Diagnosis Excessive amount of refrigerant in air conditioning system because excessive refrigerant was added during recharging
Cooling effectiveness of condenser is insufficient because condenser fins are clogged or cooling fan is faulty
Corrective Actions Clean condenser
Check operation of condenser cooling fan
If condenser is clean and fan operation is normal, check amount of refrigerant and recharge air conditioning system with proper amount of new or purified refrigerant

HINT:

For the example above, the air conditioning system is overcharged or cooling effectiveness of condenser is insufficient.


6.
E225747C09
0.938,1.771 1.208,1.99 0.271,0.219 10 *a 2.354,1.771 2.625,1.99 0.271,0.219 10 *b
*a LO
*b HI


Pressure is too high on both low and high pressure sides

Symptom Air conditioning system does not cool
The low pressure piping is too hot to touch
Probable Cause Air in air conditioning system
Diagnosis Air present in air conditioning system
Insufficient vacuum purging when evacuating air conditioning system
Corrective Actions Replace cooler dryer
Check compressor oil to see if it is dirty or insufficient
Evacuate air conditioning system and recharge it with new or purified refrigerant

NOTICE:

These gauge indications occur when the air conditioning system has been left open and then recharged without evacuating the system.


HINT:

For the example above, air is present in the air conditioning system.


7.
E225748C10
0.948,1.76 1.146,1.99 0.198,0.229 10 *a 2.354,1.76 2.552,1.99 0.198,0.229 10 *b
*a LO
*b HI


Pressure is too high on both low and high pressure sides

Symptom Air conditioning system does not cool effectively
Frost or large amount of condensation on piping on low pressure side
Probable Cause Expansion valve may be stuck open or metering refrigerant incorrectly
Diagnosis Excessive refrigerant in low pressure piping
Expansion valve open too wide
Corrective Actions Replace expansion valve

HINT:

For the example above, there is an expansion valve malfunction.


8.
E225749C09
0.927,1.76 1.167,1.99 0.24,0.229 10 *a 2.396,1.75 2.635,1.979 0.24,0.229 10 *b
*a LO
*b HI


Pressure is too high on both low and high pressure sides or pressure is too low on high pressure side

Symptom Air conditioning system does not cool effectively
Probable Cause Internal leak in compressor
Diagnosis Low compression
Leak from damaged valve or other compressor component
Corrective Actions Replace compressor

HINT:

For the example above, there is insufficient compressor compression.




iii.

Gauge readings (Reference)

E268295C04
2.99,2.417 3.156,2.417 3.156,2.417 3.156,2.729 false 3.333,2.896 3.5,2.896 3.5,2.896 3.5,3.063 false 3.469,3.396 3.635,3.396 3.635,3.396 3.635,3.229 false 3.729,3.802 3.896,3.802 3.896,3.802 3.896,3.635 false 3.583,1.667 4.167,2.063 false 4.75,2.521 5.333,2.917 false 0.229,3.135 2.219,3.333 1.99,0.198 10 false 200 (2.0, 29) 0.229,2.448 2.219,2.646 1.99,0.198 10 false 300 (3.1, 44) 0.229,1.75 2.219,1.948 1.99,0.198 10 false 400 (4.1, 58) 0.229,1.073 2.219,1.271 1.99,0.198 10 false 500 (5.1, 73) 1.375,4.24 3.365,4.438 1.99,0.198 10 false 500 (5.1, 73) 2.552,4.24 4.542,4.438 1.99,0.198 10 false 1000 (10.2, 145) 3.833,4.24 5.823,4.438 1.99,0.198 10 false 1500 (15.3, 218) 5.104,4.24 7.094,4.438 1.99,0.198 10 false 2000 (20.4, 290) 1.229,3.552 3.219,3.75 1.99,0.198 10 false 140 (1.4, 20) 1.302,3.146 3.292,3.344 1.99,0.198 10 false 200 (2.0, 29) 1.229,2.969 3.219,3.167 1.99,0.198 10 false 220 (2.2, 32) 1.24,2.635 3.229,2.833 1.99,0.198 10 false 270 (2.8, 39) 1.958,2.323 3.948,2.521 1.99,0.198 10 false 1060 (10.8, 154) 2.313,2.802 4.302,3 1.99,0.198 10 false 1200 (12.2, 174) 2.448,3.313 4.438,3.51 1.99,0.198 10 false 1250 (12.7, 181) 2.708,3.708 4.698,3.906 1.99,0.198 10 false 1320 (13.5, 191) 1.021,0.573 1.333,0.771 0.313,0.198 10 false *a 6.292,4.094 6.604,4.292 0.313,0.198 10 false *b 3.427,1.542 3.74,1.74 0.313,0.198 10 false *c 5.365,2.875 5.677,3.073 0.313,0.198 10 false *d
*a Pressure on Low Pressure Side kPa (kgf/cm2, psi) *b Pressure on High Pressure Side kPa (kgf/cm2, psi)
*c Blower High Zone *d Blower Low Zone




Post-procedure1

a.

Install the lower radiator air deflector.


b.

Install the radiator cover plate.


c.

Install the upper radiator support seal.


Hide 2.INSPECT REFRIGERANT LINE

HINT:

The following inspection specifies how to determine the cause of a refrigerant leak after determining the location of the leak using a gas leak detector. Use this procedure to determine where to clean and what to be replaced. Illustrations, specifications and part names are for reference only and may differ from the actual vehicle.


a.

Use a gas leak detector to inspect for refrigerant gas leaks.

E444210C01
1.01,3.469 1.281,3.24 false 2.677,0.844 2.865,0.5 false 5.865,0.854 6.052,0.51 false 5.521,5.917 6.104,6.052 true 5.667,1.302 6.063,1.708 true 6.469,4.313 6.156,4.552 false 2.927,0.344 3.24,0.542 0.313,0.198 10 false *1 0.844,3.458 1.156,3.656 0.313,0.198 10 false *3 6.167,5.979 6.479,6.177 0.313,0.198 10 false *4 5.771,5.354 6.083,5.552 0.313,0.198 10 false A 5.385,5.458 5.698,5.656 0.313,0.198 10 false A 4.969,5.604 5.281,5.802 0.313,0.198 10 false A 4.573,6.083 4.885,6.281 0.313,0.198 10 false A 3.896,4.854 4.229,5.115 0.333,0.26 10 false D 3.323,5.156 3.656,5.417 0.333,0.26 10 false D 2.292,2.99 2.625,3.25 0.333,0.26 10 false B 0.25,2.146 0.458,2.417 0.208,0.271 10 false B 1.219,0.948 1.469,1.198 0.25,0.25 10 false B 2.031,0.521 2.281,0.771 0.25,0.25 10 false C 3.021,0.677 3.271,0.927 0.25,0.25 10 false C 4.198,0.823 4.448,1.073 0.25,0.25 10 false C 4.792,1.979 5.104,2.177 0.313,0.198 10 false A 5.448,0.896 5.76,1.094 0.313,0.198 10 false A 6.094,0.75 6.406,0.948 0.313,0.198 10 false A 4.802,0.219 5.115,0.417 0.313,0.198 10 false A 6.104,0.406 6.417,0.604 0.313,0.198 10 false *2 6.042,1.771 6.354,1.969 0.313,0.198 10 false *4 6.51,4.167 6.823,4.365 0.313,0.198 10 false *5
*1 Compressor *2 Evaporator
*3 Condenser *4 Expansion Valve
*5 Rear Air Conditioning Unit - -


·

When leaking is occurring around the parts (A) in the illustration:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION

·

When leaking is occurring around the parts (B) in the illustration:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION

·

When leaking is occurring around the parts (C) in the illustration:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION

·

When leaking is occurring around the parts (D) in the illustration:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION



Hide 3.INSPECT FOR REFRIGERANT LEAK (EXPANSION VALVE)

NOTICE:
·

Do not reuse an O-ring that has been removed.

·

As there may be a malfunction in multiple components, make sure to perform the entire procedure.

·

If no malfunction is found in any related parts, a temporary leak may have occurred due to foreign matter on an O-ring, deformation, etc.



Pre-procedure1

a.
E440994C01
1.5,1.208 0.865,0.885 true 2.823,1.031 2.281,1.167 true 2.906,0.938 3.219,1.135 0.313,0.198 10 false *a 0.656,0.813 0.969,1.01 0.313,0.198 10 false *1
*1 Expansion Valve
*a Pipe


Remove the pipe:

NOTICE:
·

Wipe off the joint area with clean cloth before disassembly.

·

Remove the pipe straight and slowly to prevent damage to the sealing surface, and to stop foreign matter from falling.



i.

Remove the pipe from the expansion valve.



Procedure1

a.
E444196C01
0.479,0.76 0.958,0.917 true 0.292,0.677 0.604,0.875 0.313,0.198 10 false *1
*1 O-ring


Check the surface of the O-ring:

NOTICE:
·

Check the surface of the O-ring in a sufficiently bright area.

·

Degrease the surface if it is difficult to see due to oil, etc. Make sure not to lose any foreign matter that may indicate the source of a leak.



i.

Check the entire surface of the O-ring and make sure that it is free from defects such as damage (cuts, crushing, indents, etc.), foreign matter or twisting. Remove all foreign matter or replace the part if there is any damage.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION



b.
E444197C01
1.208,0.99 0.604,0.854 true 0.396,0.771 0.708,0.969 0.313,0.198 10 false *a
*a Sealing Surface


Check the sealing surface of the pipe:

NOTICE:

When removing the O-ring, be careful not to damage the O-ring or sealing surface.


i.

Remove the O-ring.


ii.

Check the sealing surface of the pipe. Remove all foreign matter or replace the part if there is any damage or corrosion.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION



c.
E444198C01
2.479,0.771 1.823,1.083 true 2.552,0.688 2.865,0.885 0.313,0.198 10 false *a
*a Sealing Surface


Check the sealing surface of the expansion valve(pipe side):

NOTICE:

Degrease the surface if it is difficult to see due to oil, etc. Make sure not to lose any foreign matter that may indicate the source of a leak.


i.

Check the entire sealing surface of the expansion valve (pipe side). Remove all foreign matter or replace the part if there isany damage or corrosion.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION



d.
E444199C01
0.75,0.125 1.063,0.323 0.313,0.198 10 false *1 2.313,0.104 2.625,0.302 0.313,0.198 10 false *2
*1 Evaporator
*2 Expansion Valve


Remove the expansion valve:

NOTICE:
·

Wipe off the joint area with clean cloth before disassembly.

·

Remove the pipe straight and slowly toprevent damage to the sealing surface,and to stop foreign matter from falling.

·

If the pipe is difficult to remove, wiggle it up and down and side to side while slowly removing it.



i.

Remove the expansion valve from the evaporator.

HINT:

If necessary, remove the air conditioning unit.





e.
E444200C01
1.865,1.646 2.615,1.01 2.615,1.01 1.885,0.813 true 2.688,0.917 3,1.115 0.313,0.198 10 false *a
*a Sealing Surface


Check the sealing surface of the expansion valve(evaporator side):

NOTICE:

Degrease the surface if it is difficult to see due tooil, etc. Make sure not to lose any foreign matterthat may indicate the source of a leak.


i.

Check the entire sealing surface of the expansion valve (evaporator side). Remove all foreign matter or replace the part if there isany damage or corrosion.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION



f.
E444201C01
1.427,1.625 2.51,1.094 2.51,1.094 1.417,0.74 true 2.594,1.01 2.906,1.208 0.313,0.198 10 false *1
*1 O-ring


Check the surface of the evaporator O-ring:

NOTICE:
·

Check the surface of the O-ring in asufficiently bright area.

·

Degrease the surface if it is difficult tosee due to oil, etc. Make sure not tolose any foreign matter that mayindicate the source of a leak.



i.

Check the entire surface of the O-ring andmake sure that it is free from defects such asdamage (cuts, crushing, indents, etc.), foreignmatter or twisting. Remove all foreign matteror replace the part if there is any damage.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION



g.
E444202C01
1.458,1.604 2.5,1.083 2.5,1.083 1.458,0.75 true 2.563,0.969 2.875,1.167 0.313,0.198 10 false *a
*a Sealing Surface


Check the sealing surface of the evaporator:

NOTICE:

When removing the O-ring, be careful not todamage the O-ring or sealing surface.


i.

Remove the O-ring.


ii.

Check the entire sealing surface of the evaporator. Remove all foreign matter or replace the part if there is any damage or corrosion.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION



Post-procedure1

a.

None


Hide 4.INSPECT FOR REFRIGERANT LEAK (CONDENSER)

NOTICE:
·

Do not reuse an O-ring that has been removed.

·

As there may be a malfunction in multiple components, make sure to perform the entireprocedure.

·

If no malfunction is found in any related parts, a temporary leak may have occurred dueto foreign matter on an O-ring, deformation, etc.



Pre-procedure1

a.
E440995C01
0.75,1.083 0.573,0.76 false 0.75,1.354 0.5,1.813 false 0.323,0.583 0.635,0.781 0.313,0.198 10 false *a 0.313,1.74 0.625,1.938 0.313,0.198 10 false *b
*a Discharge Side
*b Liquid Side


Remove the pipe:

NOTICE:
·

Wipe off the joint area with clean clothbefore disassembly.

·

Remove the pipe straight and slowly toprevent damage to the sealing surface,and to stop foreign matter from falling.



i.

Remove the pipe from the condenser.



Procedure1

a.
E444203C01
0.865,1.021 1.573,0.521 1.573,0.521 2.604,1.073 true 1.469,0.302 1.771,0.521 0.302,0.219 10 false *1
*1 O-ring


Check the surface of the O-ring:

NOTICE:
·

Check the surface of the O-ring in asufficiently bright area.

·

Degrease the surface if it is difficult tosee due to oil, etc. Make sure not tolose any foreign matter that mayindicate the source of a leak.



i.

Check the entire surface of the O-ring andmake sure that it is free from defects such asdamage (cuts, crushing, indents, etc.), foreignmatter or twisting. Remove all foreign matteror replace the part if there is any damage.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION



b.
E444204C01
0.854,1.104 1.594,0.531 1.594,0.531 2.604,1.135 true 1.438,0.313 1.75,0.51 0.313,0.198 10 false *a
*a Sealing Surface


Check the sealing surface of the pipe:

NOTICE:

When removing the O-ring, be careful not todamage the O-ring or sealing surface.


i.

Remove the O-ring.


ii.

Check the sealing surface of the pipe. Removeall foreign matter or replace the part if there isany damage or corrosion.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION



c.
E444205C01
0.969,0.844 1.708,0.313 1.708,0.313 2.844,0.875 true 1.604,0.094 1.917,0.292 0.313,0.198 10 false *a
*a Sealing Surface


Check the sealing surface of the condenser:

NOTICE:

Degrease the surface if it is difficult to see due tooil, etc. Make sure not to lose any foreign matterthat may indicate the source of a leak.


i.

Check the entire sealing surface of the condenser. Remove all foreign matter orreplace the part if there is any damage orcorrosion.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION



Post-procedure1

a.

None


Hide 5.INSPECT FOR REFRIGERANT LEAK (COMPRESSOR)

NOTICE:
·

Do not reuse an O-ring that has been removed.

·

As there may be a malfunction in multiple components, make sure to perform the entireprocedure.

·

If no malfunction is found in any related parts, a temporary leak may have occurred dueto foreign matter on an O-ring, deformation, etc.



Pre-procedure1

a.
E444206C01
1.49,0.813 0.917,0.292 true 2.573,1.375 2.073,1.01 true 0.708,0.115 1.021,0.313 0.313,0.198 10 false *a 2.573,1.375 2.885,1.573 0.313,0.198 10 false *b
*a Discharge Side
*b Suction Side


Remove the pipe:

NOTICE:
·

Wipe off the joint area with clean clothbefore disassembly.

·

Remove the pipe straight and slowly toprevent damage to the sealing surface,and to stop foreign matter from falling.



i.

Remove the pipe from the compressor.



Procedure1

a.
E444196C02
0.542,0.802 1.021,0.958 true 0.292,0.677 0.604,0.875 0.313,0.198 10 false *1
*1 O-ring


Check the surface of the O-ring:

NOTICE:
·

Check the surface of the O-ring in asufficiently bright area.

·

Degrease the surface if it is difficult tosee due to oil, etc. Make sure not tolose any foreign matter that mayindicate the source of a leak.



i.

Check the entire surface of the O-ring andmake sure that it is free from defects such asdamage (cuts, crushing, indents, etc.), foreignmatter or twisting. Remove all foreign matteror replace the part if there is any damage.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION



b.
E444197C01
1.208,0.99 0.604,0.854 true 0.396,0.771 0.708,0.969 0.313,0.198 10 false *a
*a Sealing Suface


Check the sealing surface of the pipe:

NOTICE:

When removing the O-ring, be careful not todamage the O-ring or sealing surface.


i.

Remove the O-ring.


ii.

Check the sealing surface of the pipe. Removeall foreign matter or replace the part if there isany damage or corrosion.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION



c.
E446783C01
1.021,1.281 1.292,1.76 1.292,1.76 2.51,1.104 true 1.188,1.781 1.5,1.979 0.313,0.198 10 false *a
*a Sealing Suface


Check the sealing surface of the compressor:

NOTICE:

Degrease the surface if it is difficult to see due tooil, etc. Make sure not to lose any foreign matterthat may indicate the source of a leak.


i.

Check the entire sealing surface of the compressor. Remove all foreign matter orreplace the part if there is any damage orcorrosion.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION



Post-procedure1

a.

None


Hide 6.INSPECT FOR REFRIGERANT LEAK (OTHER PARTS)

NOTICE:
·

Do not reuse an O-ring that has been removed.

·

As there may be a malfunction in multiple components, make sure to perform the entireprocedure.

·

If no malfunction is found in any related parts, a temporary leak may have occurred dueto foreign matter on an O-ring, deformation, etc.



Pre-procedure1

a.

None


Procedure1

a.

Check the surface of the pipe O-ring or component O-ring:

NOTICE:
·

Check the surface of the O-ring in asufficiently bright area.

·

Degrease the surface if it is difficult tosee due to oil, etc. Make sure not tolose any foreign matter that mayindicate the source of a leak.



i.
E444207C01
1.167,0.938 0.448,0.646 true 0.229,0.5 0.542,0.698 0.313,0.198 10 false *1
*1 O-ring


Check the entire surface of the O-ring andmake sure that it is free from defects such asdamage (cuts, crushing, indents, etc.), foreignmatter or twisting. Remove all foreign matteror replace the part if there is any damage.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION



b.

Check the sealing surface of the pipe:

NOTICE:

When removing the O-ring, be careful not todamage the O-ring or sealing surface.


i.
E444208C01
1.271,0.969 0.625,0.698 true 0.365,0.563 0.677,0.76 0.313,0.198 10 false *a
*a Sealing Surface


Remove the O-ring.


ii.

Check the sealing surface of the pipe. Removeall foreign matter or replace the part if there isany damage or corrosion.



Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION

c.

Inspect the sealing surface of the parts:

NOTICE:

Degrease the surface if it is difficult to see due tooil, etc. Make sure not to lose any foreign matterthat may indicate the source of a leak.


i.
E444211C01
1.885,0.969 2.323,0.823 true 2.385,0.729 2.698,0.927 0.313,0.198 10 false *a
*a Sealing Surface


Check the entire sealing surface of the parts. Remove all foreign matter or replace the part if there is any damage or corrosion.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION



Post-procedure1

a.

None


Hide 7.INSPECT O-RING

NOTICE:

Do not reuse an O-ring that has been removed.


a.

Check the O-ring for abnormalities.

E444212C01
3.406,0.083 3.719,0.281 0.313,0.198 10 false *a 0.76,1.792 1.073,1.99 0.313,0.198 10 false *c 4.74,0.729 5.052,0.927 0.313,0.198 10 false *b 2.74,1.781 3.052,1.979 0.313,0.198 10 false *d 4.354,1.781 4.667,1.979 0.313,0.198 10 false *e 6.208,1.76 6.521,1.958 0.313,0.198 10 false *f 3.646,2.115 3.958,2.313 0.313,0.198 10 false *g 3.677,3.76 3.99,3.958 0.313,0.198 10 false *h 3.656,5.385 3.969,5.583 0.313,0.198 10 false *i 3.656,7.01 3.969,7.208 0.313,0.198 10 false *j
*a OK Condition *b Free of cuts, crushing, indents, foreignmatter and twisting.
*c Cuts *d Crushing/Indents
*e Foreign Matter *f Twisting
*g Metal Fragments *h Resin Fragments
*i Lint *j Hair



Hide 8.INSPECT SEALING SURFACE (O-RING INSTALLATION AREA)

NOTICE:

Do not reuse an O-ring that has been removed.


a.

Check the O-ring sealing surface for abnormalities.

E444213C01
4.469,0.521 4.781,0.719 0.313,0.198 10 false *b 1.104,1.771 1.417,1.969 0.313,0.198 10 false *c 3.531,1.781 3.844,1.979 0.313,0.198 10 false *d 3.448,0.083 3.76,0.281 0.313,0.198 10 false *a 5.854,1.781 6.167,1.979 0.313,0.198 10 false *e 0.063,2.094 0.375,2.292 0.313,0.198 10 false *f 0.083,3.76 0.396,3.958 0.313,0.198 10 false *g 0.073,5.406 0.385,5.604 0.313,0.198 10 false *h 0.073,7.073 0.385,7.271 0.313,0.198 10 false *i 5.823,4.427 6.135,4.625 0.313,0.198 10 false *j 5.823,7.865 6.135,8.063 0.313,0.198 10 false *k
*a OK Condition *b Processing evidence in circumferential direction is NOT a cause of leakage.
*c Foreign Matter *d Damage
*e Corrosion *f Metal Fragments
*g Resin Fragments *h Lint
*i Hair *j White and Yellow Discoloration (Causedby Corrosion)
*k Damage (Scratches) in Axial Direction and Discoloration (Black) - -



Hide 9.INSPECT SEALING SURFACE (JOINT AREA)

a.

Check the joint areas of the components for abnormalities.

E444214C01
3.458,0.073 3.771,0.271 0.313,0.198 10 false *a 1.094,1.771 1.406,1.969 0.313,0.198 10 false *c 3.448,1.781 3.76,1.979 0.313,0.198 10 false *d 5.833,1.771 6.146,1.969 0.313,0.198 10 false *e 0.104,2.167 0.417,2.365 0.313,0.198 10 false *f 0.104,3.76 0.417,3.958 0.313,0.198 10 false *g 0.115,5.427 0.427,5.625 0.313,0.198 10 false *h 0.073,7.031 0.385,7.229 0.313,0.198 10 false *i 4.844,0.583 5.156,0.781 0.313,0.198 10 false *b 5.74,6.927 6.052,7.125 0.313,0.198 10 false *j
*a OK Condition *b Processing evidence in circumferential direction is NOT a cause of leakage.
*c Foreign Matter *d Damage
*e Corrosion *f Metal Fragments
*g Resin Fragments *h Lint
*i Hair *j Uneven Discoloration (Black) on Sealing Face



Hide 10.INSPECT FOR FAULTY EXPANSION VALVE

Pre-procedure1

a.

Recover refrigerant

i.

Connect the refrigerant recovery valve and recover the refrigerant.

NOTICE:
·

Perform this procedure in accordance with the repair manual for each vehicle.

·

Use the refrigerant recovery unit in accordance with the manufacturer's instruction manual.





Procedure1

a.

Install air conditioner service tool set:

i.
E446913

Install the air conditioner service tool set to the vehicle (high pressure side).

SST
09985-20010  


ii.
E446914

Open all the valves of the air conditioner service tool set.


iii.

Install the refrigerant recovery unit or vacuum pump to the vehicle (low pressure side).

Connection Conditions:
Tool Connected to
Air conditioner service tool set (High pressure hose) Vehicle (High pressure side)
Air conditioner service tool set (Center hose) -
Air conditioner service tool set (Low pressure hose) -
Refrigerant recovery unit or vacuum pump Vehicle (Low pressure side)



b.

Inspect expansion valve:

i.

Depending on the type of low pressure side hose of the air conditioner service tool set, prevent air from being drawn in as shown in the illustration.

E446917C02
0.083,0.083 0.396,0.281 0.313,0.198 12 false *A 2.51,0.083 2.823,0.281 0.313,0.198 12 false *B 5.083,0.083 5.396,0.281 0.313,0.198 12 false *C 4.083,0.667 4.396,0.865 0.313,0.198 10 false *a 1.5,0.667 1.813,0.865 0.313,0.198 10 false *a 6,0.667 6.313,0.865 0.313,0.198 10 false *b
*A w/ Attachment *B w/o Attachment
*C w/ Intermediate Valve - -
*a Block the end of the hose with yourthumb. *b Close the intermediate valve.



ii.
E446918

While maintaining the above state, check tha tthe gauge on the low pressure side changes when the center hose is closed and opened as shown in the illustration.

Result:
Result Judgement
The gauge indicates a negative pressure (approximately -50 kPa (-0.5 kgf/cm2, -7.3 psi)).
E446915

Expansion valve is normal
The indicated gauge pressure does not change.
E446916

Expansion valve is abnormal



Post-procedure1

a.

None