Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR
RM37H0E _58 Vehicle Interior _095300 HEATING / AIR CONDITIONING _0448330 COMPRESSOR A

HEATING / AIR CONDITIONING  COMPRESSOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
E458062N02
5.896,3.479 6.875,3.688 0.979,0.208 0.677,0.396 1.677,0.594 1,0.198 2.229,2.917 3.052,3.115 0.823,0.198 3.167,2.708 3.792,2.906 0.625,0.198 0.063,1.802 1.104,2.01 1.042,0.208 0.75,3.198 1.792,3.406 1.042,0.208 2.708,1.177 3.531,1.375 0.823,0.198 1.281,1.604 1.885,1.604 false 1.146,2.719 1.646,2.719 false 3.313,1.948 3.583,1.948 false 3.719,3.417 4.01,3.417 4.01,3.417 4.25,2.979 false 6.208,2.531 6.406,2.385 6.406,2.385 6.615,2.385 false 2.115,2.167 2.115,1.927 false 6.344,3.479 6.344,3.198 false 1.99,2.99 1.99,2.75 false 2.24,3.552 2.542,3.552 2.542,3.552 2.646,3.417 false 2.458,1.604 2.458,1.271 2.458,1.271 2.708,1.271 false 1.677,0.5 2.094,0.5 false 2.604,2.917 2.604,2.625 2.604,2.625 2.781,2.625 false 3.031,2.573 3.031,2.802 3.031,2.802 3.167,2.802 false 1.281,3.198 1.281,2.958 false 1.115,1.896 1.292,1.896 false 1.219,1.906 1.219,2.333 1.219,2.333 1.438,2.333 false 2.375,0.958 2.792,0.958 false 6.375,0.188 6.792,0.188 false 5.646,3.49 5.958,3.667 0.313,0.177 10 false ●★ 5.656,3.281 5.969,3.479 0.313,0.198 10 false x 3 6.438,3.052 6.75,3.25 0.313,0.198 10 false x 7 4.5,3.354 4.813,3.552 0.313,0.198 10 false x 12 2.302,0.396 2.625,0.594 0.323,0.198 10 false x 2 3.156,2.521 3.469,2.719 0.313,0.198 10 false x 2 2.563,1.646 2.875,1.844 0.313,0.198 10 false x 2 2.771,2.677 3.083,2.875 0.313,0.198 10 false x 2 2.083,2.146 2.24,2.344 0.156,0.198 10 false ● 1.948,2.958 2.104,3.156 0.156,0.198 10 false ● 3.531,3.271 3.969,3.552 0.438,0.281 18 false 8 6.667,2.25 7.104,2.531 0.438,0.281 18 false 7 2.063,3.417 2.5,3.698 0.438,0.281 18 false 6 0.948,2.573 1.385,2.854 0.438,0.281 18 false 5 1.073,1.438 1.51,1.719 0.438,0.281 18 false 4 3.896,1.813 4.333,2.094 0.438,0.281 18 false 3 2.188,0.802 2.625,1.083 0.438,0.281 18 false 2 5.927,3.5 6.896,3.688 0.969,0.188 8 false 7.9 (81, 70 in.*lbf) 0.729,0.417 1.76,0.583 1.031,0.167 8 false 8.0 (82, 71 in.*lbf) 2.292,2.927 3.521,3.083 1.229,0.156 8 false 24.5 (250, 18) 3.198,2.729 4.177,2.885 0.979,0.156 8 false 10 (102, 7) 0.115,1.823 1.271,1.969 1.156,0.146 8 false 9.8 (100, 87 in.*lbf) 6.198,0.052 6.635,0.333 0.438,0.281 18 false 1 0.802,3.219 1.958,3.365 1.156,0.146 8 false 9.8 (100, 87 in.*lbf) 2.781,1.198 4.01,1.354 1.229,0.156 8 false 24.5 (250, 18)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 ADJUST COMPRESSOR OIL - (Click here) - -
2 NO. 2 FC COOLING WATER PUMP CABLE BRACKET 16A1BB - - -
3 COMPRESSOR WITH MOTOR ASSEMBLY 88370 (Click here) - -
4 SUCTION HOSE SUB-ASSEMBLY A 88704A (Click here) - -
5 NO. 1 DISCHARGE HOSE SUB-ASSEMBLY 88703A (Click here) - -
6 NO. 15 FC INVERTER COOLING HOSE G91CF - - -
7 FRONT LOWER SUSPENSION MEMBER PROTECTOR 51219 - - -
8 FRONT COMPARTMENT UNDER COVER 51441N - - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

Compressor oil ND-OIL 11 or equivalent ★ Precoated part

E458105N01
5.573,1.729 6.583,1.938 1.01,0.208 5.917,2.25 6.927,2.458 1.01,0.208 5.875,2.219 6.969,2.49 1.094,0.271 2.688,3.385 4.063,3.385 4.063,3.385 4.885,3.99 true 2.646,0.688 3.552,0.688 false 5.49,2.365 5.917,2.365 false 5.333,2.031 5.333,1.833 5.333,1.833 5.573,1.833 false 5.479,2.375 5.792,2.573 0.313,0.198 10 false x 2 5.635,1.76 6.688,1.927 1.052,0.167 8 false 8.0 (82, 71 in.*lbf) 2.49,3.24 3.042,3.594 0.552,0.354 18 false 9 3.573,0.542 4.125,0.896 0.552,0.354 18 false 10 5.979,2.271 7.01,2.427 1.031,0.156 8 false 8.0 (82, 71 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

9 FC CONVERTER POWER OUTLET CABLE (INVERTER WITH CONVERTER ASSEMBLY) G9200A (Click here) - -
10 FC STACK COVER SUB-ASSEMBLY 1A906 - - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)
V100146

N*m (kgf*cm, ft.*lbf): Specified torque

E458063N02
1.646,0.792 2.167,0.792 false 1.344,0.646 1.896,1 0.552,0.354 18 false 11

Procedure Part Name Code
Z101186

Z101188

Z101187

11 SERVICE PLUG GRIP G3834 - - -

E456050N02
6.375,0.25 6.844,0.25 false 1.563,0.302 2.031,0.302 false 0.604,2.073 0.865,2.073 0.865,2.073 1.115,1.677 false 2.979,2.135 2.698,2.135 2.698,2.135 2.521,1.781 false 0.417,0.198 0.729,0.396 0.313,0.198 10 false x 6 1.854,0.854 2.167,1.052 0.313,0.198 10 false x 6 3.563,0.667 3.875,0.865 0.313,0.198 10 false x 6 2.083,0.156 2.479,0.417 0.396,0.26 18 false 16 3.01,1.969 3.375,2.229 0.365,0.26 18 false 17 0.281,1.917 0.688,2.167 0.406,0.25 18 false 15 5.563,0.104 6.469,0.458 0.906,0.354 18 false 12 - 14

Procedure Part Name Code
Z101186

Z101188

Z101187

12 CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT - (Click here) - -
13 WARM UP COMPRESSOR - (Click here) - -
14 INSPECT FOR REFRIGERANT LEAK - (Click here) - -
15 LOWER RADIATOR AIR DEFLECTOR 53295 - - -
16 RADIATOR COVER PLATE 53291B - - -
17 UPPER RADIATOR SUPPORT SEAL 53292A - - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.
E450316N01
0.51,0.115 0.792,0.469 0.281,0.354 18 false i

i.

When replacing the compressor with motor assembly with a new one, drain the following amount of oil from the position shown by the arrow in the illustration before installing the new compressor with motor assembly.

Standard:

30 cc (1.01 fl.oz) from new compressor with motor assembly.


NOTICE:
·

If a new compressor assembly with motor is installed without removing some oil, there will be too much oil in the system due to the oil remaining in the pipes of the vehicle. Excessive oil in the system prevents heat exchange in the refrigeration cycle and causes ineffective cooling.

·

Be sure to use ND-OIL 11 or equivalent compressor oil. If any compressor oil other than ND-OIL 11 is used, compressor assembly with motor insulation performance may decrease, resulting in leakage of electric power.





Hide 16A1BB 2.INSTALL NO. 2 FC COOLING WATER PUMP CABLE BRACKET

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

Hide 88370 3.INSTALL COMPRESSOR WITH MOTOR ASSEMBLY

a.
E458101C01
1.698,1.198 1.781,0.917 1.781,0.917 2.021,0.917 true 4.448,1.156 4.656,1.333 0.208,0.177 10 true *a 5,1.063 5.198,1.24 0.198,0.177 10 true *b 5.573,0.781 5.75,1.052 0.177,0.271 18 true ii 1.073,0.51 1.531,0.865 0.458,0.354 18 true i, iii 2.063,0.823 2.271,1 0.208,0.177 10 false *c
*a Connector (A) *b Connector (B)
*c Green-colored Lock - -
V113147

Slide - -


i.

Remove the insulating tape from the connector (A).


ii.

While holding the compressor with motor assembly, connect the connector (B).


iii.

While holding the compressor with motor assembly, connect the connector (A) and slide the green-colored lock as shown in the illustration to securely lock it.

CAUTION:

Make sure to wear insulated gloves.


NOTICE:

Make sure that the connector is connected securely.




b.
E458100N01
0.635,0.156 0.771,0.438 0.135,0.281 18 true i 4.25,0.177 4.427,0.458 0.177,0.281 18 true ii 6.031,1.302 6.156,1.469 0.125,0.167 10 true 1 6.385,0.552 6.51,0.719 0.125,0.167 10 true 1 4.906,0.75 5.031,0.917 0.125,0.167 10 true 2 4.75,1.573 4.875,1.74 0.125,0.167 10 true 2

i.

Using an E8 "TORX" socket wrench, temporarily install the compressor with motor assembly with the 2 stud bolts.

Torque:
10 N・m (102 kgf・cm, )


ii.

Install the compressor with motor assembly with the 2 bolts and 2 nuts in the order shown in the illustration.

Torque:
24.5 N・m (250 kgf・cm, )



c.
E456051N02
0.427,0.083 0.708,0.438 0.281,0.354 18 false i

i.

Attach the clamp.



Hide 88704A 4.CONNECT SUCTION HOSE SUB-ASSEMBLY A

a.
E450314N01
1.99,2 2.542,2.354 0.552,0.354 18 false iii 0.594,0.094 1.146,0.448 0.552,0.354 18 false i 4.406,0.094 4.958,0.458 0.552,0.365 18 false ii

i.

Remove the vinyl tape from the suction hose sub-assembly A and connecting part of the compressor with motor assembly and then sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction hose sub-assembly A.

Compressor Oil:

ND-OIL 11 or equivalent



ii.

Install the O-ring to the suction hose sub-assembly A.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



iii.

Connect the suction hose sub-assembly A to the compressor with motor assembly with the bolt (B).

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)



Hide 88703A 5.CONNECT NO. 1 DISCHARGE HOSE SUB-ASSEMBLY

a.
E450315C01
1.094,0.177 1.25,0.427 0.156,0.25 18 false i 4.313,0.177 4.5,0.438 0.188,0.26 18 false ii 3.885,2.792 4.104,3.073 0.219,0.281 18 true iii 3.25,3.542 3.49,3.688 0.24,0.146 10 true *a 2.99,3.25 3.208,3.531 0.219,0.281 18 true iv 4.094,2.646 4.323,2.792 0.229,0.146 10 true *b
*a Bolt (A) *b Bolt (B)


i.

Remove the vinyl tape from the No. 1 discharge hose sub-assembly and connecting part of the compressor with motor assembly and then sufficiently apply compressor oil to a new O-ring and the fitting surface of the No. 1 discharge hose sub-assembly.

Compressor Oil:

ND-OIL 11 or equivalent



ii.

Install the O-ring to the No. 1 discharge hose sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



iii.

Connect the No. 1 discharge hose sub-assembly to the compressor with motor assembly with the bolt (B).

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


iv.

Install the Bolt (A).

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)



Hide G91CF 6.CONNECT NO. 15 FC INVERTER COOLING HOSE

Hide 51219 7.INSTALL FRONT LOWER SUSPENSION MEMBER PROTECTOR

Hide 51441N 8.INSTALL FRONT COMPARTMENT UNDER COVER

Hide G9200A 9.CONNECT FC CONVERTER POWER OUTLET CABLE (INVERTER WITH CONVERTER ASSEMBLY)

Z101186

Click here(Click here)

Hide 1A906 10.INSTALL FC STACK COVER SUB-ASSEMBLY

Hide 12.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 53295 15.INSTALL LOWER RADIATOR AIR DEFLECTOR

Hide 53291B 16.INSTALL RADIATOR COVER PLATE

Hide 53292A 17.INSTALL UPPER RADIATOR SUPPORT SEAL