The headlight ECU sub-assembly LH supplies 5 V to the rear height control sensor LH, reads changes in the voltage that occur due to height sensor resistance changes according to the vehicle height, and performs auto leveling control.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| B241A | Rear Height Control Sensor | Detection condition:
Ignition switch ON Malfunction status:
Power source voltage malfunction is continuously detected in rear height control sensor LH Malfunction duration:
10 seconds or more |
·
Rear height control sensor sub-assembly LH ·
Headlight ECU sub-assembly LH ·
Harness or connector |
AFS | A | w/ Adaptive High Beam System |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|
| B241A | Rear Height Control Sensor | Detection condition:
Ignition switch ON Malfunction status:
Power source voltage malfunction is continuously detected in rear height control sensor LH Malfunction duration:
10 seconds or more |
·
Rear height control sensor sub-assembly LH ·
Headlight ECU sub-assembly LH ·
Harness or connector |
HL AutoLeveling | A | w/o Adaptive High Beam System |
If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>REGISTRATION
Check vehicle condition.
| Result | Proceed to |
|---|---|
| w/ Adaptive High Beam System | A |
| w/o Adaptive High Beam System | B |
A
B
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
None
NEXT
Pre-procedure1
Turn the ignition switch ON and wait for at least 10 seconds or more.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B241A is not output | A |
| B241A is output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
OK
NG
Pre-procedure1
Disconnect the A26 headlight ECU sub-assembly LH connector.
Disconnect the W5 rear height control sensor sub-assembly LH connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A26,W5)Location & Routingewd_type=routing;type=c,c;code=A26,W5 Click Connector(W5)Body>Rear Skid Control Sensor Wire LH / Rear Skid Control Sensor Wire RH>Rear Height Control Sensor Sub-Assembly LHewd_type=component;type=c;code=W5;pinno=3,2,1 |
||
| A26-16 (SBR) - W5-3 (SHB) | Always | Below 1 Ω |
| A26-17 (SHRL) - W5-2 (SHRL) | Always | Below 1 Ω |
| A26-15 (SGR) - W5-1 (SHG) | Always | Below 1 Ω |
| A26-16 (SBR) or W5-3 (SHB) - Body ground | Always | 10 kΩ or higher |
| A26-17 (SHRL) or W5-2 (SHRL) - Body ground | Always | 10 kΩ or higher |
| A26-15 (SGR) or W5-1 (SHG) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
None
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
None
NEXT
Pre-procedure1
Turn the ignition switch ON and wait for at least 10 seconds or more.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| B241A is not output | A |
| B241A is output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B