Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › ADAPTIVE HIGH BEAM SYSTEM › 2020.11–2021.08
RM37H0E _95 ADAS / AD _095317 ADVANCED DRIVER ASSISTANCE SYSTEM _0448417 ADAPTIVE HIGH BEAM SYSTEM C

ADVANCED DRIVER ASSISTANCE SYSTEM  ADAPTIVE HIGH BEAM SYSTEM  B2440  Lost Communication with AHS EDU LH Module  B2441  Lost Communication with AHS EDU RH Module  


DESCRIPTION

The headlight ECU sub-assembly sends auto leveling control signals to the headlight leveling motor via LIN communication.

The headlight leveling motor operates according to the power supply and control signals from the headlight ECU sub-assembly and sends its operation status to the headlight ECU sub-assembly via LIN communication.

The headlight ECU sub-assembly sends AHS control signals to the light control LED ECU via LIN communication.

The light control LED ECU receives power and control signals from the headlight ECU sub-assembly, controls the additional LEDs and additional fans, and sends its operation status to the headlight ECU sub-assembly via LIN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B2440 Lost Communication with AHS EDU LH Module
Detection condition:

Ignition switch ON


Malfunction status:

LIN communication is lost with light control LED ECU LH


Malfunction duration:

10 seconds or more


·

Headlight unit assembly LH

·

Light control LED ECU LH

·

Headlight ECU sub-assembly LH


AFS A
B2441 Lost Communication with AHS EDU RH Module
Detection condition:

Ignition switch ON


Malfunction status:

LIN communication is lost with light control LED ECU RH


Malfunction duration:

10 seconds or more


·

Harness or connector

·

Headlight unit assembly RH

·

Light control LED ECU RH

·

Headlight ECU sub-assembly RH

·

Headlight ECU sub-assembly LH


AFS A

Output DTC Suspected Area (Malfunction Status)
B2424 B2425 B2440 B2441

○: DTC is output.

-: DTC is not output

○ ○ ○ ○ LIN circuit (short)
Headlight ECU sub-assembly LH (Internal malfunction)
○ - ○ - Headlight ECU sub-assembly LH (Internal malfunction)
- ○ - ○ Headlight ECU sub-assembly RH (Internal malfunction)
○ - - - Headlight leveling motor LH power supply system abnormal
Headlight leveling motor LH (Internal malfunction)
Harness open circuit (Headlight ECU sub-assembly LH to headlight leveling motor LH)
Headlight ECU sub-assembly LH (Internal malfunction)
- ○ - - Headlight leveling motor RH power supply abnormal
Headlight leveling motor RH (Internal malfunction)
Harness open circuit (Headlight ECU sub-assembly RH to headlight leveling motor RH)
Headlight ECU sub-assembly RH (Internal malfunction)
- - ○ - Light control LED ECU LH power supply system abnormal
Light control LED ECU LH (Internal malfunction)
Harness open circuit (Headlight ECU sub-assembly LH to light control LED ECU LH)
Headlight ECU sub-assembly LH (Internal malfunction)
- - - ○ Light control LED ECU RH power supply system abnormal
Light control LED ECU RH (Internal malfunction)
Harness open circuit (Headlight ECU sub-assembly RH to light control LED ECU RH)
Headlight ECU sub-assembly RH (Internal malfunction)

WIRING DIAGRAM

E457826E01
0.24,2.729 2.688,2.927 2.448,0.198 10 false J 0.26,5.969 2.708,6.167 2.448,0.198 10 false Light Control LED ECU LH 5.333,1.292 6.063,1.552 0.729,0.26 10 false LIN I/F 4.708,3.396 5.438,3.656 0.729,0.26 10 false IG 4.677,0.854 5.406,1.115 0.729,0.26 10 false IG 1.229,6.521 3.344,6.75 2.115,0.229 10 false Headlight Unit Assembly LH 4.313,6.885 6.906,7.073 2.594,0.188 10 false Headlight ECU Sub-assembly LH 0.719,7.469 3.313,7.656 2.594,0.188 10 false : LIN Communication Line 4.021,3.813 4.563,4.198 0.542,0.385 10 false C 4.042,4.385 4.583,4.771 0.542,0.385 10 false C 4.031,4.969 4.573,5.354 0.542,0.385 10 false C 4.01,1.771 4.552,2.156 0.542,0.385 10 false C 4.021,1.26 4.563,1.646 0.542,0.385 10 false B 0.24,2.896 2.688,3.094 2.448,0.198 10 false Headlight Leveling Motor LH 4.031,2.281 4.573,2.667 0.542,0.385 10 false B 3.99,2.115 4.531,2.5 0.542,0.385 10 false 17 3.979,1.583 4.521,1.969 0.542,0.385 10 false 13 5.813,1.646 6.542,1.906 0.729,0.26 10 false LINL 6.302,1.573 7.031,1.833 0.729,0.26 10 false 20 6.271,1.771 7,2.031 0.729,0.26 10 false A26 4.021,1.073 4.563,1.458 0.542,0.385 10 false 9 1.667,1.156 2.208,1.542 0.542,0.385 10 false 1 1.677,1.635 2.219,2.021 0.542,0.385 10 false 3 1.688,2.146 2.229,2.531 0.542,0.385 10 false 4 4.021,3.615 4.563,4 0.542,0.385 10 false 6 4.042,4.208 4.583,4.594 0.542,0.385 10 false 3 4.031,4.802 4.573,5.188 0.542,0.385 10 false 1 1.729,4.833 2.271,5.219 0.542,0.385 10 false 21 1.698,4.24 2.24,4.625 0.542,0.385 10 false 13 1.688,3.667 2.229,4.052 0.542,0.385 10 false 12 0.25,5.802 0.792,6.188 0.542,0.385 10 false K

E457827E01
4.271,6.844 6.698,7.396 2.427,0.552 10 false Headlight ECU Sub-assembly RH 1.563,6.563 3.99,7.115 2.427,0.552 10 false Headlight Unit Assembly RH 0.26,5.99 2.688,6.542 2.427,0.552 10 false Light Control LED ECU RH 0.219,2.708 2.646,3.26 2.427,0.552 10 false J 6.271,1.781 6.906,2.031 0.635,0.25 10 false A27 6.302,1.594 6.938,1.844 0.635,0.25 10 false 20 5.177,0.844 5.813,1.094 0.635,0.25 10 false IG 5.844,1.615 6.479,1.865 0.635,0.25 10 false LINL 5.167,3.385 5.802,3.635 0.635,0.25 10 false IG 4.031,1.76 4.667,2.01 0.635,0.25 10 false C 0.219,2.854 2.646,3.406 2.427,0.552 10 false Headlight Leveling Motor RH 0.25,5.813 0.885,6.063 0.635,0.25 10 false K 4.021,4.417 4.656,4.667 0.635,0.25 10 false C 4.031,3.802 4.667,4.052 0.635,0.25 10 false C 4.031,4.969 4.667,5.219 0.635,0.25 10 false C 4.031,4.802 4.667,5.052 0.635,0.25 10 false 1 1.646,1.135 2.281,1.385 0.635,0.25 10 false 1 1.656,1.646 2.292,1.896 0.635,0.25 10 false 3 4.042,4.208 4.677,4.458 0.635,0.25 10 false 3 4.031,3.646 4.667,3.896 0.635,0.25 10 false 6 1.656,2.167 2.292,2.417 0.635,0.25 10 false 4 3.979,1.583 4.615,1.833 0.635,0.25 10 false 13 4.031,1.094 4.667,1.344 0.635,0.25 10 false 9 4.031,1.271 4.667,1.521 0.635,0.25 10 false B 4.031,2.271 4.667,2.521 0.635,0.25 10 false B 3.99,2.104 4.625,2.354 0.635,0.25 10 false 17 1.708,3.677 2.344,3.927 0.635,0.25 10 false 12 1.719,4.24 2.354,4.49 0.635,0.25 10 false 13 0.74,7.458 3.313,7.75 2.573,0.292 10 false : LIN Communication Line 1.708,4.875 2.344,5.125 0.635,0.25 10 false 21


CAUTION / NOTICE / HINT

NOTICE:

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>ADAPTIVE HIGH BEAM SYSTEM>REGISTRATION


PROCEDURE

1.CHECK FOR DTC

Pre-procedure1

a.

Clear the DTCs.

Body Electrical > AFS > Clear DTCs
50002 165

b.

Turn the ignition switch to ON and wait for at least 10 seconds or more.


Procedure1

a.

Check for DTCs.

Body Electrical > AFS > Trouble Codes
50001 165
Result:
Result Proceed to
B2424, B2425 B2440 and B2441 are not output A
B2424, B2425, B2440 and B2441 are output B
B2424 and B2440 are output C
B2425 and B2441 are output D
B2440 is output E
B2441 is output F



Post-procedure1

a.

None



A

B

C

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

D

E

2.CHECK HEADLIGHT UNIT ASSEMBLY LH

F

5.CHECK HEADLIGHT UNIT ASSEMBLY RH
2.CHECK HEADLIGHT UNIT ASSEMBLY LH

Pre-procedure1

a.

Remove the light control LED ECU LH.

HINT:

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>AHS ECU>REMOVAL


E442303C04
1.615,0.625 1.958,0.854 0.344,0.229 5.25,0.656 5.594,0.885 0.344,0.229 1.75,0.677 1.906,0.875 0.156,0.198 10 false C 5.396,0.708 5.552,0.906 0.156,0.198 10 false K 0.646,0.656 0.885,0.854 0.24,0.198 10 false *a 4.188,0.677 4.448,0.875 0.26,0.198 10 false *b
*a Component without harness connected
(Headlight ECU Sub-assembly LH)
*b Component without harness connected
(Light Control LED ECU LH)



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-6 - K-12 Always Below 1 Ω
C-3 - K-13 Always Below 1 Ω
C-1 - K-21 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPLACE HEADLIGHT UNIT ASSEMBLY LH

3.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

Pre-procedure1

a.
E442304C03
1.448,0.323 1.938,0.563 0.49,0.24 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.646,0.354 1.958,0.51 0.313,0.156 10 false K
*a Component without harness connected
(Light Control LED ECU LH)


Disconnect the light control LED ECU LH connector.


b.

Reconnect the except light control LED ECU LH connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K-12 - K-21 Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

4.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

Pre-procedure1

a.
E384719C26
1.427,0.219 1.927,0.438 0.5,0.219 1.448,2.563 1.948,2.781 0.5,0.219 2.677,4.25 2.51,4.25 2.51,4.25 2.125,3.75 true 0.125,0.063 0.438,0.219 0.313,0.156 10 false *a 0.125,2.385 0.438,2.542 0.313,0.156 10 false *b 1.583,2.583 1.896,2.74 0.313,0.156 10 false A27 1.615,0.24 1.927,0.396 0.313,0.156 10 false C 2.74,4.146 3.094,4.333 0.354,0.188 10 false LINL
*a Component with harness connected
(Headlight ECU Sub-assembly LH)
*b Front view of wire harness connector
(to Headlight ECU Sub-assembly RH)


Remove the headlight ECU sub-assembly LH as a unit with the connectors still connected.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Disconnect the A27 headlight ECU sub-assembly RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A27)Location & Routing

Click Connector(A27)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Headlight ECU Sub-Assembly RH

C-3 - A27-20 (LINL) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE LIGHT CONTROL LED ECU LH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

5.CHECK HEADLIGHT UNIT ASSEMBLY RH

Pre-procedure1

a.

Remove the light control LED ECU RH.

HINT:

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>AHS ECU>REMOVAL


E442303C05
1.615,0.625 1.958,0.854 0.344,0.229 5.25,0.656 5.594,0.885 0.344,0.229 1.75,0.677 1.906,0.875 0.156,0.198 10 false C 5.396,0.708 5.552,0.906 0.156,0.198 10 false K 0.646,0.656 0.885,0.854 0.24,0.198 10 false *a 4.188,0.677 4.448,0.875 0.26,0.198 10 false *b
*a Component without harness connected
(Headlight ECU Sub-assembly RH)
*b Component without harness connected
(Headlight Leveling Motor RH)



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-6 - K-12 Always Below 1 Ω
C-3 - K-13 Always Below 1 Ω
C-1 - K-21 Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

6.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPLACE HEADLIGHT UNIT ASSEMBLY RH

6.CHECK HEADLIGHT ECU SUB-ASSEMBLY LH

Pre-procedure1

a.
E442304C03
1.448,0.323 1.938,0.563 0.49,0.24 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.646,0.354 1.958,0.51 0.313,0.156 10 false K
*a Component without harness connected
(Light Control LED ECU RH)


Disconnect the light control LED ECU RH connector.


b.

Reconnect the except light control LED ECU RH connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K-12 - K-21 Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

7.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

7.CHECK HEADLIGHT ECU SUB-ASSEMBLY RH

Pre-procedure1

a.
E384719C27
1.427,0.219 1.927,0.438 0.5,0.219 1.448,2.563 1.948,2.781 0.5,0.219 2.677,4.25 2.51,4.25 2.51,4.25 2.125,3.75 true 0.125,0.063 0.438,0.219 0.313,0.156 10 false *a 0.125,2.385 0.438,2.542 0.313,0.156 10 false *b 1.583,2.583 1.896,2.74 0.313,0.156 10 false A26 1.615,0.24 1.927,0.396 0.313,0.156 10 false C 2.74,4.146 3.094,4.333 0.354,0.188 10 false LINL
*a Component with harness connected
(Headlight ECU Sub-assembly RH)
*b Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)


Remove the headlight ECU sub-assembly RH as a unit with the connectors still connected.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL



b.

Disconnect the A26 headlight ECU sub-assembly LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A26)Location & Routing

Click Connector(A26)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Headlight ECU Sub-Assembly LH

C-3 - A26-20 (LINL) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE LIGHT CONTROL LED ECU RH

NG

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH