| *1 | FC AIR BY-PASS VALVE PIPE ASSEMBLY | *2 | WIRE HARNESS CLAMP BRACKET |
| *3 | STUD BOLT | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| ★ | Precoated part | - | - |
89421S
1.INSTALL TURBO PRESSURE SENSOR
17341Y
2.INSTALL AIR HOSE
| *a | Rib of Intercooler With Sensor Assembly | *b | Hose Paint Mark |
| *c | Upper Side of Vehicle | *d | RH Side of Vehicle |
| *e | 2 to 7 mm (0.0787 to 0.276 in.) | *f | 90° |
Install the air hose to the intercooler with sensor assembly with the hose clamp.
Make sure to position the hose clamp as shown in the illustration.
17900
3.INSTALL INTERCOOLER WITH SENSOR ASSEMBLY
| *a | Rib of FC Air Compressor With Motor Assembly | *b | Hose Paint Mark |
| *c | Upper Side of Vehicle | *d | RH Side of Vehicle |
| *e | 2 to 5 mm (0.0787 to 0.197 in.) | *f | 90° |
| *g | 0 to 4 mm (0 to 0.158 in.) | - | - |
Connect the air hose to the FC air compressor with motor assembly and temporarily install the intercooler with sensor assembly with the 3 bolts as shown in the illustration.
Tighten the 3 bolts in the order shown A, B and C.
Tighten the hose clamp D as shown in the illustration.
17B21
4.INSTALL FC STACK AIR INLET HOSE
| *a | Rib of Intercooler With Sensor Assembly | *b | Hose Paint Mark (White) |
| *c | Rib of FC Stack Air Inlet Pipe Assembly | *d | Hose Paint Mark (Yellow) |
| *e | 0 to 7 mm (0 to 0.276 in.) | - | - |
Install the FC stack air inlet hose to the Intercooler with sensor assembly and FC stack air inlet pipe assembly with the 2 hose clamps.
Make sure to position the hose clamp as shown in the illustration.
5.INSTALL FC INTERCOOLER HOSE
| *1 | No. 1 FC Intercooler Hose | *2 | No. 2 FC Intercooler Hose |
| *3 | No. 3 Radiator Hose Bracket | - | - |
| *a | 2 to 7 mm (0.0787 to 0.276 in.) | *b | 120° |
| *c | Hose Paint Mark | *d | Pipe Paint Mark |
| *e | Correct | *f | Incorrect |
| *g | 0 mm (0 in.) | *h | More than 0 mm (0 in.) |
Connect the No. 3 radiator hose bracket to the intercooler with sensor assembly with the bolt.
Connect the No. 1 FC intercooler hose and No. 2 FC intercooler hose to the intercooler with sensor assembly and slide the 2 hose clips to secure it.
Make sure to position the hose clip as shown in the illustration.
8.ADD COOLANT (TOYOTA GENUINE FC STACK COOLANT (Pre-mixed))
9.INSPECT FOR COOLANT (TOYOTA GENUINE FC STACK COOLANT (Pre-mixed)) LEAK
58404B
10.INSTALL REAR NO. 4 FLOOR BOARD SUB-ASSEMBLY
51420A
11.INSTALL FRONT COMPARTMENT UNDER COVER ASSEMBLY
51219
12.INSTALL FRONT LOWER SUSPENSION MEMBER PROTECTOR
51441N
13.INSTALL FRONT COMPARTMENT UNDER COVER
1A906
14.INSTALL FC STACK COVER SUB-ASSEMBLY