Home › Engine / Hybrid System › COOLING › COOLANT
RM37H0E _51 Engine / Hybrid System _097304 COOLING _0455465 COOLANT A

COOLING  COOLANT  REPLACEMENT  


CAUTION / NOTICE / HINT

NOTICE:
·

Do not turn the ignition switch to ON (READY) when there is no coolant (Toyota genuine FC stack coolant (Pre-mixed)) in the FC radiator reserve tank assembly.

·

If the coolant (Toyota genuine FC stack coolant (Pre-mixed)) passages are filled incorrectly, follow the countermeasures according to "Countermeasures when coolant (Toyota genuine FC stack coolant (Pre-mixed)) passages are filled incorrectly".

Click hereEngine / Hybrid System>COOLING>COOLANT>PRECAUTION



PROCEDURE

Hide 1. CAUTIONS FOR COOLANT (TOYOTA GENUINE FC STACK COOLANT (Pre-mixed))

Hide 1A906 2.REMOVE FC STACK COVER SUB-ASSEMBLY

Hide 51441N 3.REMOVE FRONT COMPARTMENT UNDER COVER

Hide 51219 4.REMOVE FRONT LOWER SUSPENSION MEMBER PROTECTOR

Hide 51420A 5.REMOVE FRONT COMPARTMEMT UNDER COVER ASSEMBLY

Hide 6.DRAIN COOLANT (TOYOTA GENUINE FC STACK COOLANT (Pre-mixed))

CAUTION:
·

When the coolant (Toyota genuine FC stack coolant (Pre-mixed)) is hot, do not remove the reserve tank cap, FC radiator assembly drain cock plug or the intercooler assembly side drain cock plug.

·

Fluid and steam may spray out due to high pressure, possibly resulting in burns.


A483865C01
2.646,1.167 2.74,0.927 2.74,0.927 2.906,0.927 true 5.917,4.583 5.75,4.583 5.75,4.583 5.583,4.25 true 5.875,0.885 5.333,0.885 true 2.927,0.854 3.188,1.01 0.26,0.156 10 true *1 5.948,4.51 6.198,4.708 0.25,0.198 10 true *2 5.917,0.823 6.156,0.99 0.24,0.167 10 true *3
*1 Reserve tank cap *2 FC Radiator Assembly Drain Cock Plug
*3 Intercooler Assembly Side Drain Cock Plug - -



NOTICE:

Collect the removed coolant (Toyota genuine FC stack coolant (Pre-mixed)) and measure the amount, then check that the same amount or greater has been added when coolant is refilled.


a.
A479554C01
1.323,1.927 1.781,1.927 true 1.083,1.854 1.302,2.052 0.219,0.198 10 true *a
*a Hose


Connect a hose with an inside diameter of 9 mm (0.354 in.) to the FC radiator assembly drain cock as shown in the illustration.


b.
A479553C01
1.354,1.563 1.771,1.563 true 1.146,1.49 1.344,1.667 0.198,0.177 10 true *a
*a Hose


Connect a hose with an inside diameter of 8 mm (0.315 in.) to the intercooler assembly side drain cock plug as shown in the illustration.


c.

Loosen the FC radiator assembly drain cock plug and intercooler assembly side drain cock plug.

A483866C01
4.615,3.063 4.365,3.063 4.365,3.063 4.229,2.521 true 3.01,3.26 3.427,3.26 false 2.094,0.438 2.427,0.438 2.427,0.438 2.677,0.771 true 1.906,0.375 2.219,0.573 0.313,0.198 10 false *1 3.479,3.198 3.792,3.396 0.313,0.198 10 false *2 4.646,3 4.958,3.198 0.313,0.198 10 false *3
*1 Reserve tank cap *2 FC Radiator Assembly Drain Cock Plug
*3 Intercooler Assembly Side Drain Cock Plug - -



d.

Remove the reserve tank cap. Then drain the engine coolant (Toyota genuine FC stack coolant (Pre-mixed)).

NOTICE:

Collect the removed coolant (Toyota genuine FC stack coolant (Pre-mixed)) and measure the amount, then check that the same amount or greater has been added when coolant is refilled.



e.

Tighten the FC radiator assembly drain cock plug and intercooler assembly side drain cock plug by hand.


f.

Disconnect the hose from the FC radiator assembly drain cock plug and intercooler assembly side drain cock plug.


Hide 7.ADD COOLANT (TOYOTA GENUINE FC STACK COOLANT (Pre-mixed))

NOTICE:
·

Make sure to use the GTS to perform air bleeding of the coolant (Toyota genuine FC stack coolant (Pre-mixed)) passages.

·

If air bleeding is performed without using the GTS, the air bleeding of the coolant (Toyota genuine FC stack coolant (Pre-mixed)) passages may be incomplete.

·

If the vehicle is driven while the coolant (Toyota genuine FC stack coolant (Pre-mixed)) system is contaminated with air, the following DTC may be stored.

DTC No. Detection Item
P1D2F00 FC Coolant Pump Performance
P1DE400 FC Cooling System Performance

·

Before refilling coolant (Toyota genuine FC stack coolant 50), check "Filling instructions when refilling coolant (Toyota genuine FC stack coolant 50)".

Click hereEngine / Hybrid System>COOLING>COOLANT>WORK OUTLINE EXPLANATION



HINT:

The coolant (Toyota genuine FC stack coolant (Pre-mixed)) capacity: 16.4 liters (17.3 US qts, 14.4 Imp. qts)]


a.

Natural injection

i.

Remove the reserve tank cap.


ii.

Remove the FC cooling water ion exchanger element.

Click hereGeneral>MAINTENANCE>ION EXCHANGER ELEMENT>REMOVAL


iii.
A483858C02
2.167,1.229 2.448,1.542 2.448,1.542 2.646,1.542 true 0.792,1.51 1.125,1.51 true 2.656,1.448 2.854,1.635 0.198,0.188 10 true *1 0.594,1.427 0.792,1.615 0.198,0.188 10 true *2
*1 No. 9 FC radiator hose
*2 No. 13 FC radiator hose


Fill the FC cooling water ion exchanger assembly approximately half-full with the Toyota genuine coolant (Toyota genuine FC stack coolant (Pre-mixed)).


iv.

Squeeze the No. 9 FC radiator hose and No. 13 FC radiator hose several times by hand and then check the coolant level in the FC cooling water ion exchanger assembly. If the coolant level is low, fill with the coolant (Toyota genuine FC stack coolant (Pre-mixed)).


v.

Install the FC cooling water ion exchanger element.

Click hereGeneral>MAINTENANCE>ION EXCHANGER ELEMENT>INSTALLATION


vi.
A483891

Pour coolant (Toyota genuine FC stack coolant (Pre-mixed)) up to the MAX line of the FC radiator reserve tank assembly and install reserve tank cap.



b.

FC stack coolant Amount Check + Fill

i.

Turn the ignition switch on (IG).


ii.

Using the GTS, check that the SOC is 40% or higher.

Powertrain > EV > Data List
Tester Display
Hybrid/EV Battery SOC
50003 397 320
Result:
Result Action
Below 40% Charge by using the THS charger.
(Click here)
40% or higher Go to next step



iii.
A479216C05
2.031,1.542 1.417,1.542 false 1.542,0.49 2.229,0.229 2.229,0.229 2.406,0.229 true 2.448,0.156 2.76,0.313 0.313,0.156 10 false *1 1.208,1.458 1.521,1.615 0.313,0.156 10 false *a
*1 Auxiliary Battery
*a Battery Charger


To prevent auxiliary battery depletion, connect the battery charger to the auxiliary battery to charge the auxiliary battery.


iv.

Set the rotary valve to a 50% open position during the Active Test.

Powertrain > EV > Active Test
Tester Display
Control the Radiator Rotary Valve
50004 397 15

v.

Exit the Active Test.


vi.

Turn the ignition switch on (READY).[*1]

HINT:

If the coolant (Toyota genuine FC stack coolant 50) level is very low after turning the ignition switch on (READY), the water pump is operated and air bleeding is performed for approximately 1 minute without starting the FC system.


Result:
Result Action
"FC System Malfunction" is displayed on multi-information display Go to next step
"FC System Malfunction" is not displayed on the multi-information display Go to Bleed Air + Fill


1.

Clear the DTCs.

2.

Turn the ignition switch off (IG).

3.

Remove the reserve tank cap.

4.

Pour coolant (Toyota genuine FC stack coolant (Pre-mixed)) up to the MAX line of the FC radiator reserve tank assembly and install reserve tank cap.

HINT:

Repeat the steps following turning the ignition switch on (READY) [*1] until the FC system starts.





c.

Bleed Air + Fill

i.

Following the instructions on the GTS, perform the utility "FC Stack Coolant Air Bleeding".

Powertrain > EV > Utility
Tester Display
FC Stack Coolant Air Bleeding
50005 397 4692
HINT:
·

Coolant (Toyota genuine FC stack coolant (Pre-mixed)) filling is performed multiple times during the air bleeding procedure.

·

If the ignition switch was turned on (READY) during air bleeding, wait for 1 minute before proceeding to the next step.

·

If an error is displayed during air bleeding, start over the Utility (air bleeding).




ii.

If the GTS screen displays instruction to inject into the FC cooling water ion exchanger assembly, use the following procedures to fill the coolant.

1.

Remove the FC cooling water ion exchanger element.

Click hereGeneral>MAINTENANCE>ION EXCHANGER ELEMENT>REMOVAL

2.
A483858C02
2.167,1.229 2.448,1.542 2.448,1.542 2.646,1.542 true 0.792,1.51 1.125,1.51 true 2.656,1.448 2.854,1.635 0.198,0.188 10 true *1 0.594,1.427 0.792,1.615 0.198,0.188 10 true *2
*1 No. 9 FC radiator hose
*2 No. 13 FC radiator hose


Fill the FC cooling water ion exchanger assembly approximately half-full with the Toyota genuine coolant (Toyota genuine FC stack coolant (Pre-mixed)).

3.

Squeeze the No. 9 FC radiator hose and No. 13 FC radiator hose several times by hand and then check the coolant level in the FC cooling water ion exchanger assembly. If the coolant level is low, fill with the coolant (Toyota genuine FC stack coolant (Pre-mixed)).

4.

Install the FC cooling water ion exchanger element.

Click hereGeneral>MAINTENANCE>ION EXCHANGER ELEMENT>INSTALLATION



iii.
A483911

When the screen shown in the illustration is displayed, exit the Air Bleeding Utility.


iv.

Operate the vehicle for approximately 5 minutes and check that the heating function operates normally.


v.

If it is not possible to fill with the amount or more of the coolant (Toyota genuine FC stack coolant (Pre-mixed)) as much as removed or the heating function does not operate normally, perform the following procedure.


vi.

Turn OFF the air conditioning system.[*1]


vii.

Set the heater valve to the middle position during the Active Test.[*2]

Body Electrical > Air Conditioner > Active Test
Tester Display
Heater Valve
50004 121 103

viii.
A483855C01
1.063,0.75 1.479,0.75 true 2.146,1.188 2.563,1.188 true 0.854,0.677 1.052,0.833 0.198,0.156 10 true *1 2.573,1.115 2.771,1.271 0.198,0.156 10 true *2
*1 Water Hose Sub-assembly E
*2 Water Hose Sub-assembly D


Slide the clip and disconnect the water hose sub-assembly E from the water hose sub-assembly D.[*3]


ix.

Using a dropper, fill with the coolant (Toyota genuine FC stack coolant (Pre-mixed)) from the water hose sub-assembly until the coolant level can be seen.[*4]


x.

Connect the water hose sub-assembly E to the water hose sub-assembly D, and slide the clip to secure the hose as shown in the illustration.[*5]

NOTICE:

Do not apply excessive force to the water hose sub-assembly E.


A483895C01
4.188,1.24 4.333,1.583 4.333,1.583 4.5,1.583 true 1.354,0.75 1.51,0.948 0.156,0.198 10 true A 5.594,0.104 5.781,0.302 0.188,0.198 10 false *f 6.104,0.115 6.313,0.313 0.208,0.198 10 false *d 6.292,0.563 6.5,0.76 0.208,0.198 10 false *e 3.865,0.292 4.073,0.49 0.208,0.198 10 false *c 4.552,1.51 4.76,1.708 0.208,0.198 10 false *b 5.083,0.156 5.271,0.354 0.188,0.198 10 false *a
*a View A *b Paint Mark
*c 3 to 7 mm (0.119 to 0.276 in.) *d 45°
*e 30° *f Front Side



xi.

Using the Active Text, perform air bleeding.[*6]

Body Electrical > Air Conditioner > Active Test
Tester Display
Water Pump
50004 121 20
1.

Operate the electric water pump for approximately 3 minutes and bleed air during the Active Test.

2.

Check the coolant level of the FC radiator reserve tank assembly and refill up to the MAX line if the coolant level is low.



xii.

Check if the heating function operates normally.[*7]

HINT:

If the heating function does not operate normally, perform the procedure from steps [*1] to [*7] 3 times.



xiii.

Exit the Active Test.

HINT:

If it is not possible to fill with the amount or more of the coolant (Toyota genuine FC stack coolant (Pre-mixed)) as much as removed or the heating function does not operate normally, perform the coolant adding procedure from the first step again.



xiv.

When air is completely bled, check the coolant level of the FC radiator reserve tank assembly and refill up to the MAX line if the coolant level is low.


xv.

If the engine coolant level is above the MAX line, drain engine coolant so that the engine coolant level is the MAX line.



Hide 8.INSPECT FOR COOLANT (TOYOTA GENUINE FC STACK COOLANT (Pre-mixed)) LEAK

Hide 51420A 9.INSTALL FRONT COMPARTMEMT UNDER COVER ASSEMBLY

Hide 51219 10.INSTALL FRONT LOWER SUSPENSION MEMBER PROTECTOR

Hide 51441N 11.INSTALL FRONT COMPARTMENT UNDER COVER

Hide 1A906 12.INSTALL FC STACK COVER SUB-ASSEMBLY