| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door lock with motor assembly removal/installation are shown below.
| Replacement Part | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
|
*: When performing learning using the GTS. Click here |
|||
| Removal and installation of auxiliary battery terminal | Memorize steering angle neutral point | Lane control system (for Stereo camera type) | for Stereo Camera type:
for Mono Camera type: |
| Lane control system (for Mono camera type) | |||
| Parking support brake system* | |||
| Pre-collision system (for Stereo camera type) | |||
| Pre-collision system (for Mono camera type) | |||
| Adaptive high beam system | |||
Lighting system (EXT)
Cornering lights |
|||
| Variable gear ratio steering system | |||
| Parking assist monitor system | |||
| Panoramic view monitor system | |||
| Initialize Rear Door Sunshade System | Rear door sunshade system | ||
| Initialize power trunk lid system | Power trunk lid system | ||
·
Rear multiplex network door ECU LH ·
Rear multiplex network door ECU RH ·
Rear multiplex network door ECU LH or rear multiplex network door ECU RH is the connectors are disconnected |
Initialize rear door sunshade system | The rear door sunshade system does not operate | |
·
Power window regulator motor assembly LH ·
Power window regulator motor assembly RH ·
Rear door window regulator assembly LH ·
Rear door window regulator assembly RH ·
Rear door glass sub-assembly LH ·
Rear door glass sub-assembly RH ·
Rear door glass run LH ·
Rear door glass run RH ·
Rear door No. 3 glass run LH ·
Rear door No. 3 glass run RH |
Initialize power window control system | ·
Auto up and down function ·
Jam protection function ·
Catch protection function ·
Remote control function ·
Key-linked function ·
Wireless transmitter-linked function ·
Key-off operation function ·
Window open warning function |
|
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
When removing the rear door glass sub-assembly LH, move the rear door glass sub-assembly LH to the lowest position before disconnecting the auxiliary battery negative (-) terminal.
1. PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
68174A
6.REMOVE REAR DOOR GLASS INNER WEATHERSTRIP
68199
8.REMOVE REAR DOOR BELT REAR SEAL
89225
10.REMOVE MULTIPLEX NETWORK DOOR REAR ECU (w/ Double Locking System)
67646A
11.REMOVE REAR DOOR ARMREST SET BRACKET
67842E
12.REMOVE REAR DOOR SERVICE HOLE COVER
13.REMOVE HOLE PLUG
68152C
14.REMOVE REAR DOOR GLASS RUN
67408E
15.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
69804
18.REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY
69060A
19.REMOVE REAR DOOR WITH MOTOR LOCK ASSEMBLY
| *1 | Release Plate | - | - |
|
Remove in this Direction |
|
TORX Screw |
|
Connector | - | - |
Disconnect the connector.
Using a T30 "TORX" socket wrench, remove the 3 TORX screws.
Move the rear door lock with motor assembly downward as shown in the illustration to disconnect it from the release plate of the rear door outside handle frame sub-assembly, and remove the rear door lock with motor assembly.
Do not damage to body by Rear door lock assembly LH.
69038A
20.REMOVE REAR DOOR LOCK COVER SUB-ASSEMBLY
|
Open | - | - |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw to open the rear door lock cover sub-assembly LH.
Disengage the claw to remove the rear door lock cover sub-assembly LH.
69740E
21.REMOVE REAR DOOR LOCK OPEN LEVER REMOTE CONTROL CABLE
|
Remove in this Direction | - | - |
69780E
22.REMOVE REAR DOOR INSIDE LOCK/UNLOCK KNOB LOCKING CABLE
|
Remove in this Direction | - | - |
69318D
23.REMOVE DOOR LOCK WIRING HARNESS SEAL
|
|
When reusing the rear door lock with motor assembly: