Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)
RM37H0E _59 Vehicle Exterior _095308 MIRROR (EXT) _0453657 POWER MIRROR CONTROL SYSTEM(w/ Reverse Shift-linked Mirror) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Reverse Shift-linked Mirror)  Driver Side Power Mirror cannot be Adjusted with Power Mirror Switch  


DESCRIPTION

The outer mirror switch assembly sends the mirror adjust switch signals to the main body ECU (multiplex network body ECU) via LIN communication. The main body ECU (multiplex network body ECU) then sends the received mirror adjust switch signals to the front multiplex network door ECU (driver door) via CAN communication. Upon receiving the signal, the front multiplex network door ECU (driver door) operates the vertical and horizontal mirror motors, which are built into the outer rear view mirror assembly (driver door), to adjust the mirror surface position.

WIRING DIAGRAM

for LHD:



E458513E01
1.573,4.427 3.5,4.625 1.927,0.198 10 false Outer Mirror Switch Assembly 1.583,4.208 2.042,4.406 0.458,0.198 10 false E33 0.656,7.229 2.969,7.458 2.313,0.229 10 false Outer Rear View Mirror Assembly LH 3.188,7.563 4.698,7.979 1.51,0.417 10 false Front Multiplex Network Door ECU LH 3.188,7.365 3.646,7.563 0.458,0.198 10 false z29 0.646,8.458 2.417,8.656 1.771,0.198 10 false : CAN Communication Line 5.802,7.396 6.948,8.052 1.146,0.656 10 false Main Body ECU (Multiplex Network Body ECU) 5.813,7.177 6.271,7.375 0.458,0.198 10 false D14 3.031,5.417 3.188,5.615 0.156,0.198 10 false 1 2.958,5.844 3.219,6.042 0.26,0.198 10 false 10 3.01,6.271 3.167,6.469 0.156,0.198 10 false 9 3.25,5.427 3.563,5.625 0.313,0.198 10 false MV 3.26,5.865 3.573,6.063 0.313,0.198 10 false M+ 3.271,6.271 3.583,6.469 0.313,0.198 10 false MH 4.083,5.948 4.542,6.146 0.458,0.198 10 false CPU 4.563,0.573 4.875,0.771 0.313,0.198 10 false M+ 4.438,2.375 4.833,2.573 0.396,0.198 10 false MSW 4.677,3.167 4.906,3.406 0.229,0.24 10 false E 4.927,0.573 5.083,0.771 0.156,0.198 10 false 4 4.938,2.375 5.094,2.573 0.156,0.198 10 false 5 4.938,3.167 5.094,3.365 0.156,0.198 10 false 7 5.656,0.563 5.813,0.76 0.156,0.198 10 false 7 5.667,2.365 5.823,2.563 0.156,0.198 10 false 8 5.656,3.167 5.813,3.365 0.156,0.198 10 false 9 5.906,0.688 6.521,0.885 0.615,0.198 10 false MIRB 5.906,2.49 6.521,2.688 0.615,0.198 10 false MIRS 5.906,3.281 6.521,3.479 0.615,0.198 10 false MIRE 0.979,5.74 2.333,5.917 1.354,0.177 10 false Vertical Mirror Motor 0.823,6.167 2.302,6.354 1.479,0.188 10 false Horizontal Mirror Motor 1.354,1.896 3.875,2.125 2.521,0.229 10 false Mirror Select and Surface Adjust Switch 1.563,3.656 3.573,3.865 2.01,0.208 10 false Retractable Outer Mirror Switch 1.271,1.083 1.688,1.313 0.417,0.229 10 false Left 2.052,1.094 2.479,1.292 0.427,0.198 10 false Down 2.833,1.083 3.604,1.281 0.771,0.198 10 false Right 3.615,1.094 3.927,1.292 0.313,0.198 10 false Up 0.969,2.844 1.385,3.073 0.417,0.229 10 false Left 1.823,2.833 2.594,3.031 0.771,0.198 10 false Right 2.5,2.844 2.917,3.073 0.417,0.229 10 false Left 3.313,2.833 4.083,3.031 0.771,0.198 10 false Right 0.906,6.656 2.51,6.833 1.604,0.177 10 false Outer Mirror Retractor LH

for RHD:


E458513E02
1.573,4.427 3.5,4.625 1.927,0.198 10 false Outer Mirror Switch Assembly 1.583,4.208 2.042,4.406 0.458,0.198 10 false E16 0.656,7.208 2.969,7.438 2.313,0.229 10 false Outer Rear View Mirror Assembly RH 3.177,7.563 4.688,7.979 1.51,0.417 10 false Front Multiplex Network Door ECU RH 3.188,7.354 3.646,7.552 0.458,0.198 10 false z28 0.646,8.458 2.417,8.656 1.771,0.198 10 false : CAN Communication Line 5.813,7.375 6.958,8.031 1.146,0.656 10 false Main Body ECU (Multiplex Network Body ECU) 5.813,7.167 6.271,7.365 0.458,0.198 10 false D14 3.031,5.417 3.188,5.615 0.156,0.198 10 false 1 2.958,5.844 3.219,6.042 0.26,0.198 10 false 10 3.01,6.271 3.167,6.469 0.156,0.198 10 false 9 3.25,5.427 3.563,5.625 0.313,0.198 10 false MV 3.26,5.865 3.573,6.063 0.313,0.198 10 false M+ 3.271,6.271 3.583,6.469 0.313,0.198 10 false MH 4.083,5.948 4.542,6.146 0.458,0.198 10 false CPU 4.563,0.573 4.875,0.771 0.313,0.198 10 false M+ 4.438,2.375 4.833,2.573 0.396,0.198 10 false MSW 4.677,3.167 4.906,3.406 0.229,0.24 10 false E 4.927,0.573 5.083,0.771 0.156,0.198 10 false 4 4.938,2.375 5.094,2.573 0.156,0.198 10 false 5 4.938,3.167 5.094,3.365 0.156,0.198 10 false 7 5.656,0.563 5.813,0.76 0.156,0.198 10 false 7 5.667,2.365 5.823,2.563 0.156,0.198 10 false 8 5.656,3.167 5.813,3.365 0.156,0.198 10 false 9 5.906,0.688 6.521,0.885 0.615,0.198 10 false MIRB 5.906,2.49 6.521,2.688 0.615,0.198 10 false MIRS 5.906,3.281 6.521,3.479 0.615,0.198 10 false MIRE 0.979,5.74 2.333,5.917 1.354,0.177 10 false Vertical Mirror Motor 0.823,6.167 2.302,6.354 1.479,0.188 10 false Horizontal Mirror Motor 1.354,1.896 3.875,2.125 2.521,0.229 10 false Mirror Select and Surface Adjust Switch 1.563,3.656 3.573,3.865 2.01,0.208 10 false Retractable Outer Mirror Switch 1.271,1.083 1.688,1.313 0.417,0.229 10 false Left 2.052,1.094 2.479,1.292 0.427,0.198 10 false Down 2.833,1.083 3.604,1.281 0.771,0.198 10 false Right 3.615,1.094 3.927,1.292 0.313,0.198 10 false Up 0.969,2.844 1.385,3.073 0.417,0.229 10 false Left 1.823,2.833 2.594,3.031 0.771,0.198 10 false Right 2.5,2.844 2.917,3.073 0.417,0.229 10 false Left 3.313,2.833 4.083,3.031 0.771,0.198 10 false Right 0.896,6.667 2.531,6.865 1.635,0.198 10 false Outer Mirror Retractor RH


CAUTION / NOTICE / HINT

NOTICE:
·

The power mirror control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power mirror control system after confirming that the communication system is functioning properly.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS (MIRROR SELECTION SW [L/R])
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mirror Selection SW (R) Mirror select switch signal for RH mirror OFF or ON OFF: Mirror select switch in the neutral position (off)
ON: Mirror select switch in the R position
for LHD
Mirror Selection SW (L) Mirror select switch signal for LH mirror OFF or ON OFF: Mirror select switch in the neutral position (off)
ON: Mirror select switch in the L position
for RHD
Body Electrical > Main Body > Data List
Tester Display
Mirror Selection SW (R)
Mirror Selection SW (L)
50003 123 98,99
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR)

NG

3.INSPECT OUTER MIRROR SWITCH ASSEMBLY
2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR)

OK

REPLACE FRONT MULTIPLEX NETWORK DOOR ECU (DRIVER DOOR)

NG

REPLACE OUTER MIRROR RETRACTOR (DRIVER DOOR)

3.INSPECT OUTER MIRROR SWITCH ASSEMBLY

OK

4.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPLACE OUTER MIRROR SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Disconnect the E33*1 or E16*2 outer mirror switch assembly.

*1: for LHD

*2: for RHD



b.

Disconnect the D14 main body ECU (multiplex network body ECU).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(E33,D14)Location & Routing

Click Connector(E33)Body>Front Door Wire LH / Front Door Wire RH>Outer Mirror Switch Assembly

Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECU

E33-4 (M+) - D14-7 (MIRB) Always Below 1 Ω
E33-5 (MSW) - D14-8 (MIRS) Always Below 1 Ω
E33-7 (E) - D14-9 (MIRE) Always Below 1 Ω
E33-4 (M+) or D14-7 (MIRB) - Body ground Always 10 kΩ or higher
E33-5 (MSW) or D14-8 (MIRS) - Body ground Always 10 kΩ or higher
E33-7 (E) or D14-9 (MIRE) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(E16,D14)Location & Routing

Click Connector(E16)Body>Front Door Wire LH / Front Door Wire RH>Outer Mirror Switch Assembly

Click Connector(D14)Instrument Panel>Instrument Panel Wire>Main Body ECU

E16-4 (M+) - D14-7 (MIRB) Always Below 1 Ω
E16-5 (MSW) - D14-8 (MIRS) Always Below 1 Ω
E16-7 (E) - D14-9 (MIRE) Always Below 1 Ω
E16-4 (M+) or D14-7 (MIRB) - Body ground Always 10 kΩ or higher
E16-5 (MSW) or D14-8 (MIRS) - Body ground Always 10 kΩ or higher
E16-7 (E) or D14-9 (MIRE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR