Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM37H0E _59 Vehicle Exterior _095212 WIPER / WASHER _0447384 WIPER AND WASHER SYSTEM C

WIPER / WASHER  WIPER AND WASHER SYSTEM  B1245  Lost Communication with Wiper ECU LIN  


DESCRIPTION

The main body ECU (multiplex network body ECU) and windshield wiper motor assembly communicate via LIN communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
B1245 Lost Communication with Wiper ECU LIN
Detection condition:

Ignition switch ON (IG+ voltage 9.5 V or higher)


Malfunction Status:

Communication malfunction with windshield wiper motor assembly


Malfunction Duration:

10 seconds or more


·

Windshield wiper motor assembly

·

Harness or connector

·

Windshield wiper relay (WIPER NO. 1)

·

Main body ECU (multiplex network body ECU)


○ Main Body B

WIRING DIAGRAM

E458760E02
1.563,1.219 1.802,1.385 0.24,0.167 10 false +B 0.885,3.906 1.208,4.073 0.323,0.167 10 false GND 1.563,3.906 1.854,4.083 0.292,0.177 10 false LIN 1.917,1.083 2.49,1.281 0.573,0.198 10 false 6*1, 7*2 0.271,3.781 0.854,3.958 0.583,0.177 10 false 4*1, 1*2 1.917,3.729 2.604,3.927 0.688,0.198 10 false 7*1, 6*2 3.104,2.375 4.604,2.75 1.5,0.375 10 false Windshield Wiper Relay (WIPER NO. 1) 4.354,1.813 4.51,2.01 0.156,0.198 10 false 1 3.271,1.802 3.427,2 0.156,0.198 10 false 2 3.26,1.115 3.417,1.313 0.156,0.198 10 false 3 4.354,1.115 4.51,1.313 0.156,0.198 10 false 5 4.583,0.5 5.552,0.667 0.969,0.167 10 false WIPER NO. 1 2.563,0.26 4.073,0.458 1.51,0.198 10 false from Auxiliary Battery 5.385,1.677 5.615,1.854 0.229,0.177 10 false 21 5.333,1.927 5.625,2.094 0.292,0.167 10 false D11 5.781,1.948 6.229,2.135 0.448,0.188 10 false WPS 5.427,3.677 5.583,3.875 0.156,0.198 10 false 3 5.333,3.917 5.646,4.094 0.313,0.177 10 false D12 5.781,3.927 6.229,4.115 0.448,0.188 10 false LIN3 0.781,4.594 1.885,4.99 1.104,0.396 10 false Windshield Wiper Motor Assembly 0.792,4.417 1.083,4.594 0.292,0.177 10 false A37 5.365,4.5 7.031,4.875 1.667,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 0.51,5.406 2.177,5.604 1.667,0.198 10 false : LIN Communication Line 2.542,5.406 3.323,5.615 0.781,0.208 10 false *1: for LHD 3.479,5.396 4.26,5.594 0.781,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect fuses for circuits related to this system before performing the following inspection procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



PROCEDURE

1.CLEAR THE DTC

Pre-procedure1

a.

None.


Procedure1

a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch to ON and wait for at least 10 seconds.



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
B1245 is not output A
Only B1245 is output B
B1245 and B1373 are output C



A

B

3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BATTERY)

C

3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BATTERY)

Pre-procedure1

a.

Disconnect the A37 windshield wiper motor assembly connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A37)Location & Routing

Click Connector(A37)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Windshield Wiper Motor Assembly

A37-6 (+B) - Body ground Approximately 60 seconds have elapsed after ignition switch is turned off Below 1 V
A37-6 (+B) - Body ground Ignition switch ON or within approximately 60 seconds of ignition switch being turned off 11 to 14 V

for RHD
Tester Connection Switch Condition Specified Condition

Click Location & Routing(A37)Location & Routing

Click Connector(A37)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Windshield Wiper Motor Assembly

A37-7 (+B) - Body ground Approximately 60 seconds have elapsed after ignition switch is turned off Below 1 V
A37-7 (+B) - Body ground Ignition switch ON or within approximately 60 seconds of ignition switch being turned off 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BODY GROUND)

NG

6.INSPECT WINDSHIELD WIPER RELAY (WIPER NO. 1)
4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the A37 windshield wiper motor assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(A37)Location & Routing

Click Connector(A37)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Windshield Wiper Motor Assembly

A37-4 (GND) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(A37)Location & Routing

Click Connector(A37)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Windshield Wiper Motor Assembly

A37-1 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - WINDSHIELD WIPER MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - WINDSHIELD WIPER MOTOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the D12 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the A37 windshield wiper motor assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(D12,A37)Location & Routing

Click Connector(D12)Instrument Panel>Instrument Panel Wire>Main Body ECU

Click Connector(A37)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Windshield Wiper Motor Assembly

D12-3 (LIN3) - A37-7 (LIN) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(D12,A37)Location & Routing

Click Connector(D12)Instrument Panel>Instrument Panel Wire>Main Body ECU

Click Connector(A37)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Windshield Wiper Motor Assembly

D12-3 (LIN3) - A37-6 (LIN) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT WINDSHIELD WIPER RELAY (WIPER NO. 1)

OK

7.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY [WIPER NO. 1] - BATTERY AND BODY GROUND)

NG

REPLACE WINDSHIELD WIPER RELAY (WIPER NO. 1)

7.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY [WIPER NO. 1] - BATTERY AND BODY GROUND)

Pre-procedure1

a.
E371103C01
0.135,0.083 0.448,0.281 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Windshield Wiper Relay [WIPER NO. 1])


Remove the windshield wiper relay (WIPER NO. 1) form No. 2 front compartment relay block.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Windshield wiper relay (WIPER NO. 1) terminal 2 - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Windshield wiper relay (WIPER NO. 1) terminal 5 - Body ground Ignition switch off 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

8.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY [WIPER NO. 1] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND WINDSHIELD WIPER MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY [WIPER NO. 1] - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND WINDSHIELD WIPER MOTOR ASSEMBLY)

Pre-procedure1

a.

Remove the windshield wiper relay (WIPER NO. 1) form No. 2 front compartment relay block.


b.

Disconnect the D11 main body ECU (multiplex network body ECU) connector.


c.

Disconnect the A37 windshield wiper motor assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(D11,A37)Location & Routing

Click Connector(D11)Instrument Panel>Instrument Panel Wire>Main Body ECU

Click Connector(A37)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Windshield Wiper Motor Assembly

D11-21 (WPS) - Windshield wiper relay (WIPER NO. 1) terminal 1 Always Below 1 Ω
Windshield wiper relay (WIPER NO. 1) terminal 3 - A37-6 (+B) Always Below 1 Ω
D11-21 (WPS) or Windshield wiper relay (WIPER NO. 1) terminal 1 - Body ground Always 10 kΩ or higher
Windshield wiper relay (WIPER NO. 1) terminal 3 or A37-6 (+B) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(D11,A37)Location & Routing

Click Connector(D11)Instrument Panel>Instrument Panel Wire>Main Body ECU

Click Connector(A37)Engine Compartment>Front Compartment Main Wire / No. 3 Front Compartment Wire / No. 4 Front Compartment Wire>Windshield Wiper Motor Assembly

D11-21 (WPS) - Windshield wiper relay (WIPER NO. 1) terminal 1 Always Below 1 Ω
Windshield wiper relay (WIPER NO. 1) terminal 3 - A37-7 (+B) Always Below 1 Ω
D11-21 (WPS) or Windshield wiper relay (WIPER NO. 1) terminal 1 - Body ground Always 10 kΩ or higher
Windshield wiper relay (WIPER NO. 1) terminal 3 or A37-7 (+B) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None.



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR