Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for RHD)
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0454012 BRAKE ACTUATOR(for RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for RHD)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C447594N02
3.417,0.667 5.667,4.75 2.25,4.083 4.708,4.375 5.542,4.625 0.833,0.25 4.458,2.51 5.542,2.76 1.083,0.25 4.5,2.552 5.5,2.719 1,0.167 4.75,4.417 5.5,4.583 0.75,0.167 3.719,4.344 4.469,4.344 true 4.229,4.25 4.479,4.25 4.479,4.25 4.479,4.5 false 4.25,4.5 4.75,4.5 false 4.25,3.333 4.75,3.333 false 4.25,3.083 4.5,3.083 4.5,3.083 4.5,3.333 false 3.719,3.188 4.5,3.188 true 5,2.385 5,2.552 false 4.198,3.958 4.781,3.958 false 4.198,3.698 4.531,3.698 4.531,3.698 4.531,3.948 false 3.698,3.833 4.531,3.833 true 1.969,0.583 2.219,0.583 false 5.667,1.917 6,1.917 false 4.333,1.583 4.667,1.583 false 4.313,2.333 4.479,2.333 false 4.552,2.573 5.635,2.823 1.083,0.25 8 false 5.4 (55, 48 in.*lbf) 5.146,3.219 5.479,3.552 0.333,0.333 18 false 1 5.135,2.25 5.469,2.5 0.333,0.25 10 false x 4 5.188,3.844 5.521,4.177 0.333,0.333 18 false 2 1.802,0.458 2.135,0.792 0.333,0.333 18 false 3 6.052,1.854 6.385,2.104 0.333,0.25 10 false *1 4.708,1.531 5.042,1.781 0.333,0.25 10 false *2 4.521,2.271 4.854,2.521 0.333,0.25 10 false *3 4.813,4.438 5.646,4.688 0.833,0.25 8 false 19 (194, 14)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 BRAKE ACTUATOR BRACKET CUSHION 44547B (Click here) - -
2 NO. 1 BRAKE ACTUATOR CASE COLLAR 44521A (Click here) - -
3 BRAKE ACTUATOR ASSEMBLY 44510 (Click here) - -

*1 BRAKE ACTUATOR BRACKET ASSEMBLY *2 NO. 1 BRAKE ACTUATOR BRACKET
*3 NO. 2 BRAKE ACTUATOR BRACKET - -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) - -

C448771N02
3.896,2.792 4.646,3.042 0.75,0.25 3.938,2.833 4.604,3 0.667,0.167 1.958,0.75 2.708,0.917 0.75,0.167 1.917,0.708 2.75,0.958 0.833,0.25 3.615,0.917 4.365,1.083 0.75,0.167 3.573,0.875 4.406,1.125 0.833,0.25 2,0.083 2.917,0.417 0.917,0.333 1.958,0.042 2.958,0.458 1,0.417 6.083,2.75 7,3.083 0.917,0.333 6.042,2.708 7.042,3.125 1,0.417 2.917,3.667 3.583,3.833 0.667,0.167 2.875,3.625 3.625,3.875 0.75,0.25 0.104,0.083 1.104,0.25 1,0.167 0.063,0.042 1.146,0.292 1.083,0.25 4.917,3.417 5.167,3.417 false 5.625,1.531 5.625,2.917 true 3.583,3.75 3.75,3.75 3.75,3.75 3.75,3.667 false 3.198,1 3.615,1 true 3.302,0.75 3.385,0.75 3.385,0.75 3.385,1 false 1.104,0.167 1.354,0.167 false 1.833,0.5 2.333,0.5 2.333,0.5 2.333,0.75 false 3.479,0.396 3.417,0.167 3.417,0.167 2.917,0.167 true 3.167,0.167 3.25,0.417 true 3.063,0.167 3.156,0.448 true 3.292,0.167 3.375,0.417 true 5.333,1.635 5.333,2.917 5.333,2.917 6.083,2.917 false 5.75,2.292 5.75,2.917 false 5.938,2.313 5.938,2.917 true 5.75,1.417 5.75,1.083 5.75,1.083 6,1.083 false 3.667,2.667 3.667,2.396 3.667,2.396 3.917,2.396 false 3.75,1.667 4,1.667 false 1.083,0.667 1.333,0.667 false 3.917,0.333 3.917,0.167 3.917,0.167 4.167,0.167 false 5.208,0.417 5.458,0.417 false 1.167,2.708 1.25,2.708 false 4.604,2.917 4.771,2.917 false 5.469,3.292 5.802,3.708 0.333,0.417 18 false 4 3.833,3.531 4.083,3.781 0.25,0.25 10 false x 4 1.5,0.188 1.75,0.438 0.25,0.25 10 false x 2 6.135,2.771 6.969,2.938 0.833,0.167 8 false 19.5 (199, 14) 6.135,2.938 6.969,3.104 0.833,0.167 8 false 17.4 (177, 13) * 4.219,2.25 4.552,2.667 0.333,0.417 18 false 5 4.323,1.531 4.99,1.865 0.667,0.333 18 false 6, 8 0.896,0.542 1.229,0.958 0.333,0.417 18 false 7 4.49,0.073 4.823,0.49 0.333,0.417 18 false 10 5.979,0.302 6.646,0.635 0.667,0.333 18 false 9 5.792,0.375 6.458,0.708 0.667,0.333 10 false ● 6.292,1 6.958,1.333 0.667,0.333 18 false 11 0.885,2.552 1.552,2.885 0.667,0.333 18 false 12 4,2.854 4.75,3.104 0.75,0.25 8 false 11 (112, 8) 2.021,0.771 2.854,1.021 0.833,0.25 8 false 19 (194, 14) 3.677,0.938 4.51,1.188 0.833,0.25 8 false 19 (194, 14) 2.052,0.104 2.969,0.354 0.917,0.25 8 false 15.2 (155, 11) 2.052,0.271 2.969,0.521 0.917,0.25 8 false 13.4 (137, 10) * 2.969,3.688 3.719,3.938 0.75,0.25 8 false 11 (112, 8) 0.156,0.104 1.24,0.354 1.083,0.25 8 false 8.0 (82, 71 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

4 NO. 3 BRAKE ACTUATOR BRACKET 44593 (Click here) - -
5 NO. 5 BRAKE ACTUATOR BRACKET 44595 (Click here) - -
6 TEMPORARILY INSTALL BRAKE ACTUATOR WITH BRACKET - (Click here) - -
7 WIRE HARNESS CLAMP BRACKET - - - -
8 INSTALL BRAKE ACTUATOR WITH BRACKET - (Click here) - -
9 BRAKE TUBE CLAMP - (Click here) - -
10 CONNECT BRAKE TUBE - (Click here) - -
11 INSTALL BRAKE TUBE - (Click here) - -
12 FRONT COMPARTMENT MAIN WIRE 82111C (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) * For use with a union nut wrench
● Non-reusable part - -

C448770N02
3.25,1.833 4,2 0.75,0.167 1.969,3.083 2.969,3.25 1,0.167 1.375,4.531 2.375,4.698 1,0.167 0.333,3.417 0.583,3.417 false 0.75,4.167 1,4.167 false 2.75,2.75 2.75,2.917 2.75,2.917 3,2.917 false 1.083,1.083 0.833,1.083 0.833,1.083 0.833,1.833 false 6.583,0.167 6.833,0.167 false 2.333,2.146 2.333,1.917 2.333,1.917 3.25,1.917 false 3.167,1.917 3.167,2.042 false 1.552,3.5 1.885,3.5 1.885,3.5 1.885,3.167 false 1.802,3.167 1.969,3.167 false 1.375,4.615 1.208,4.615 false 3.583,0.5 3.333,0.5 3.333,0.5 3.333,1.083 false 6.583,0.583 6.865,0.583 false 6.583,0.958 6.813,0.958 false 6.583,1.417 6.833,1.417 false 0.042,3.302 0.542,3.635 0.5,0.333 18 false 13 1.052,4.052 1.552,4.385 0.5,0.333 18 false 14 3.052,2.792 3.552,3.125 0.5,0.333 18 false 15 2.219,1.104 2.469,1.354 0.25,0.25 10 false x 6 3.635,0.385 4.135,0.719 0.5,0.333 18 false 16 1.135,0.958 1.635,1.292 0.5,0.333 18 false 17 5.865,0.458 6.667,0.833 0.802,0.375 18 false 18. 21 5.385,0.833 6.938,1.479 1.552,0.646 18 false 20, 22, 24 6.25,0.042 6.667,0.375 0.417,0.333 18 false 23 1.583,3.583 2,3.833 0.417,0.25 10 false x 2 6.271,1.292 6.771,1.625 0.5,0.333 18 false 19 3.323,1.854 3.99,2.104 0.667,0.25 8 false 49 (500, 36) 2.021,3.104 3.188,3.354 1.167,0.25 8 false 8.0 (82, 71 in.*lbf) 1.427,4.552 2.594,4.719 1.167,0.167 8 false 8.0 (82, 71 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

13 RELAY BLOCK - - - -
14 FC JUNCTION CABLE BRACKET - - - -
15 FENDER APRON BRACE SUB-ASSEMBLY RH 53705F - - -
16 COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY 55708 - - -
17 RADIATOR COVER PLATE 53291B - - -
18 FILL RESERVOIR WITH BRAKE FLUID - - - -
19 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
20 UPDATE ECU SECURITY KEY - - - (Click here)
21 BLEED BRAKE SYSTEM - - (Click here) -
22 PERFORM INITIALIZATION AND CALIBRATION - - - (Click here)
23 CHECK AND CLEAR DTC - - - -
24 INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL - - - (Click here)

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

PROCEDURE

Hide 44547B 1.INSTALL BRAKE ACTUATOR BRACKET CUSHION

Z101186

HINT:

Perform this procedure only when replacement of the brake actuator bracket cushions is necessary.



Hide 44521A 2.INSTALL NO. 1 BRAKE ACTUATOR CASE COLLAR

Z101186

NOTICE:

Make sure that the No. 1 brake actuator case collar is in full contact with the brake actuator bracket cushion.


HINT:

Perform this procedure only when replacement of the No. 1 brake actuator case collars is necessary.



Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

Hide 44510 3.INSTALL BRAKE ACTUATOR ASSEMBLY

Z101186

NOTICE:
·

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake tubes because the brake actuator assembly is filled with brake fluid.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.




a.
C448769N02
4.042,1.385 4.198,1.583 0.156,0.198 10 false 1 4.375,0.281 4.531,0.479 0.156,0.198 10 false 2 2.802,1.292 2.958,1.49 0.156,0.198 10 false 3 4.052,2.333 4.208,2.531 0.156,0.198 10 true 4 0.427,0.073 1.01,0.469 0.583,0.396 18 false i, ii

i.

Temporarily install the brake actuator assembly to the brake actuator bracket assembly with the 4 bolts.


ii.

Install the brake actuator assembly to the brake actuator bracket assembly with the 4 bolts in the order shown in the illustration.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)



Hide 44593 4.INSTALL NO. 3 BRAKE ACTUATOR BRACKET

Z101186

HINT:

Perform this procedure only when replacement of the No. 3 brake actuator bracket is necessary.



Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)

Hide 44595 5.INSTALL NO. 5 BRAKE ACTUATOR BRACKET

Z101186

HINT:

Perform this procedure only when replacement of the No. 5 brake actuator bracket is necessary.



a.
C447327N02
3.021,1.542 3.177,1.74 0.156,0.198 10 true 1 4.438,1.469 4.594,1.667 0.156,0.198 10 true 2 2.594,0.615 2.75,0.813 0.156,0.198 10 true 3 2.771,0.26 2.927,0.458 0.156,0.198 10 true 4 0.448,0.052 1.01,0.458 0.563,0.406 18 false i, ii

i.

Temporarily install the No. 5 brake actuator bracket to the body with the 4 bolts.


ii.

Install the No. 5 brake actuator bracket to the body with the 4 bolts in the order shown in the illustration.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)



Hide 6.TEMPORARILY INSTALL BRAKE ACTUATOR WITH BRACKET

Z101186

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tubes from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator with bracket by the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Temporarily install the brake actuator with bracket while avoiding the brake tubes.



a.
C447326


Hide 7.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C447317N01
2.573,0.771 2.729,0.969 0.156,0.198 10 true A 3.813,1.406 3.969,1.604 0.156,0.198 10 true A 3.51,0.104 3.667,0.302 0.156,0.198 10 true B

Torque:
Bolt A : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Bolt B : 19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 8.INSTALL BRAKE ACTUATOR WITH BRACKET

Z101186

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tubes from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator with bracket by the connector.

·

Do not drop the brake actuator with bracket when carrying it.




a.
C448768N01
0.438,0.073 1.354,0.656 0.917,0.583 18 false i 2.604,0.24 2.729,0.448 0.125,0.208 10 true 1 2.542,1.115 2.667,1.323 0.125,0.208 10 true 2

i.

Tighten the bolt and nut in the order shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)



Hide 9.INSTALL BRAKE TUBE CLAMP

Z101186

NOTICE:

Do not kink or damage the brake tubes.



a.
C447323C01
4.99,0.417 5.156,0.417 5.156,0.417 5.24,0.667 true 5.323,0.24 5.49,0.24 5.49,0.24 5.583,0.667 true 6.167,0.333 6,0.333 6,0.333 5.917,0.667 true 6.167,1.417 6,1.417 6,1.417 5.917,1.083 true 2.833,0.542 2.917,0.292 2.917,0.292 3.25,0.292 true 0.427,0.052 1.01,0.552 0.583,0.5 18 false i 4.813,0.354 5.063,0.604 0.25,0.25 10 false *a 5.156,0.188 5.469,0.344 0.313,0.156 10 false *b 6.219,0.271 6.552,0.521 0.333,0.25 10 false *c 6.219,1.354 6.469,1.604 0.25,0.25 10 false *d 3.302,0.229 3.552,0.396 0.25,0.167 10 true *e
*a To Front Wheel Cylinder Assembly RH *b To Front Wheel Cylinder Assembly LH
*c To Rear Wheel Cylinder Assembly RH *d To Rear Wheel Cylinder Assembly LH
*e Paint Mark - -


i.

Engage the 4 clamps to install a new brake tube clamp so that it is at the center of the paint mark as shown in the illustration.



Hide 10.CONNECT BRAKE TUBE

Z101186

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tube from the connecting parts.




a.
C447320C01
2.917,0.552 3.25,0.135 3.25,0.135 3.417,0.135 true 2.854,0.583 2.604,0.417 2.604,0.417 2.188,0.417 true 2.781,0.656 2.531,0.74 2.531,0.74 2.115,0.74 true 2.74,0.74 2.49,1.073 2.49,1.073 2.156,1.073 true 3.323,1 3.073,1 3.073,1 2.99,0.833 true 3.531,0.833 3.198,0.833 3.198,0.833 3.115,0.667 true 3.375,0.948 3.625,1.115 0.25,0.167 10 true *a 3.573,0.781 3.823,0.948 0.25,0.167 10 true *b 1.979,1.021 2.229,1.188 0.25,0.167 10 false *c 1.938,0.688 2.271,0.938 0.333,0.25 10 false *d 2,0.365 2.333,0.615 0.333,0.25 10 false *e 3.479,0.083 3.729,0.25 0.25,0.167 10 true *f 0.417,0.042 0.75,0.458 0.333,0.417 18 false i
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly *b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly RH *d To Front Wheel Cylinder Assembly LH
*e To Rear Wheel Cylinder Assembly RH *f To Rear Wheel Cylinder Assembly LH


i.

Temporarily tighten the 6 brake tubes to the correct position on the brake actuator assembly as shown in the illustration.



b.
C447325C01
5.771,2.229 5.854,2.396 5.854,2.396 5.938,2.396 false 5.083,2.417 5.333,2.667 0.25,0.25 10 false *a 5.99,2.333 6.323,2.583 0.333,0.25 10 false *b 0.427,0.063 1.802,0.417 1.375,0.354 18 false i
*a Torque Wrench Fulcrum Length *b Union Nut Wrench


i.

Using a union nut wrench, fully tighten the 4 brake tubes.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)





Hide 11.INSTALL BRAKE TUBE

Z101186

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tube from the connecting parts.




a.
C447322C01
2.365,2.177 2.365,2.427 2.365,2.427 2.531,2.427 false 5.479,1.521 5.646,1.521 5.646,1.521 5.729,1.271 false 6.063,1.26 6.146,1.51 6.146,1.51 6.396,1.51 false 1.583,2.417 1.917,2.583 0.333,0.167 10 false *a 2.573,2.375 2.823,2.625 0.25,0.25 10 false *b 0.417,0.073 1.25,0.406 0.833,0.333 18 false i, ii 5.292,1.469 5.542,1.719 0.25,0.25 10 false *c 6.448,1.458 6.698,1.708 0.25,0.25 10 false *d
*a Torque Wrench Fulcrum Length *b Union Nut Wrench
*c From 1st Chamber of Brake Booster with Master Cylinder Assembly *d From 2nd Chamber of Brake Booster with Master Cylinder Assembly


i.

Using a union nut wrench, fully tighten the 2 brake tubes.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.378 in.)):

17.4 N*m (177 kgf*cm, 13 ft.*lbf)




ii.

Engage the 2 clamps to install the 2 brake tubes.



Hide 82111C 12.CONNECT FRONT COMPARTMENT MAIN WIRE

Z101186

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the actuator connector can be connected smoothly.

·

Do not allow water, oil or dirt to enter the connector.




Hide 13.INSTALL RELAY BLOCK

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

Hide 14.INSTALL FC JUNCTION CABLE BRACKET

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

Hide 53705F 15.INSTALL FENDER APRON BRACE SUB-ASSEMBLY RH

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

Hide 55708 16.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53291B 17.INSTALL RADIATOR COVER PLATE

Hide 18.FILL RESERVOIR WITH BRAKE FLUID

Hide 19.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 21.BLEED BRAKE SYSTEM

Hide 22.PERFORM INITIALIZATION AND CALIBRATION


b.

for Electric Parking Brake System:

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>UTILITY


Hide 24. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART