Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE PEDAL STROKE SENSOR (for RHD) › 2020.11–2021.08
RM37H0E _54 Brake _096746 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0454017 BRAKE PEDAL STROKE SENSOR(for RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE PEDAL STROKE SENSOR(for RHD)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C447596N02
0.75,2.25 1.75,2.417 1,0.167 0.708,2.208 1.792,2.458 1.083,0.25 6.083,0.5 6.5,0.5 false 2.74,2.604 2.99,2.604 false 6.083,0.917 6.5,0.917 false 1.75,2.333 2,2.333 false 5.656,0.375 6.24,0.708 0.583,0.333 18 false 1, 4 3.375,2.49 3.958,2.823 0.583,0.333 18 false 2 5.917,0.802 6.25,1.135 0.333,0.333 18 false 3 2.104,2.406 2.406,2.656 0.302,0.25 10 false x 2 0.802,2.271 1.969,2.604 1.167,0.333 8 false 8.5 (87, 75 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 INSPECT AND ADJUST BRAKE PEDAL HEIGHT - - - (Click here)
2 INSTALL BRAKE PEDAL STROKE SENSOR ASSEMBLY 89510D (Click here) - -
3 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
4 ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY 89510D - - (Click here)

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) - -

C448767N02
6.333,0.667 6.75,0.667 false 6.333,0.25 6.75,0.25 false 3.583,1.083 3.583,1.333 3.583,1.333 3.833,1.333 false 6.302,1.042 6.719,1.042 false 5.865,0.542 6.448,0.958 0.583,0.417 18 false 5, 7 3.885,1.198 4.219,1.615 0.333,0.417 18 false 6 5.708,0.927 6.375,1.354 0.667,0.427 18 false 8, 10 6.146,0.125 6.729,0.542 0.583,0.417 18 false 9

Procedure Part Name Code
Z101186

Z101188

Z101187

5 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - (Click here) - -
6 LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY 73900 - - -
7 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
8 PERFORM CALIBRATION - - - (Click here)
9 CHECK AND CLEAR DTC - - - -
10 INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL - - - (Click here)

CAUTION / NOTICE / HINT

PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

Hide 89510D 2.INSTALL BRAKE PEDAL STROKE SENSOR ASSEMBLY

a.

When installing a new brake pedal stroke sensor assembly:

C447598C03
5,2.583 5.167,2.333 5.167,2.333 5.333,2.333 true 5.042,2.719 5.125,2.969 5.125,2.969 5.292,2.969 true 5.063,1 5.313,1 true 1.938,1.042 2.104,1.375 0.167,0.333 18 false ii 5.208,0.396 5.458,0.729 0.25,0.333 18 true iv 5.385,2.281 5.635,2.448 0.25,0.167 10 true *a 5.365,0.948 5.615,1.115 0.25,0.167 10 true *c 2.125,2.458 2.292,2.792 0.167,0.333 18 false ii 2.917,2.677 3.167,3.01 0.25,0.333 18 true iii 4.854,1.958 5.104,2.292 0.25,0.333 18 true i 5.344,2.917 5.594,3.083 0.25,0.167 10 true *b
*a Brake Pedal Stroke Sensor Assembly Lever *b Brake Pedal Groove
*c Brake Pedal Stroke Sensor Assembly Lever Set Pin - -


i.

Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.

NOTICE:

Do not break the brake pedal stroke sensor assembly lever set pin before installing the brake pedal stroke sensor assembly with the 2 nuts.



ii.

Install a new brake pedal stroke sensor assembly to the brake pedal support assembly with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.

·

Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.

·

Do not drop the brake pedal stroke sensor assembly.

·

If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.




iii.

Connect the connector.


iv.

Firmly depress the brake pedal to break the brake pedal stroke sensor assembly lever set pin and remove the broken lever set pin.



b.

When reusing the brake pedal stroke sensor assembly:

C447599C01
5,1.688 5.083,1.354 5.083,1.354 5.25,1.354 true 5.031,1.823 5.115,2.073 5.115,2.073 5.281,2.073 true 5.302,1.302 5.552,1.469 0.25,0.167 10 true *a 1.927,1.021 2.094,1.354 0.167,0.333 18 false ii 2.531,1.333 2.698,1.667 0.167,0.333 18 false i 2.917,2.667 3.167,3 0.25,0.333 18 true iii 5.333,2.021 5.583,2.188 0.25,0.167 10 true *b 2.125,2.448 2.292,2.781 0.167,0.333 18 false ii 4.865,1.083 5.031,1.417 0.167,0.333 18 true i
*a Brake Pedal Stroke Sensor Assembly Lever *b Brake Pedal Groove


i.

Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.


ii.

Install the brake pedal stroke sensor assembly to the brake pedal support assembly and tighten the 2 nuts.

NOTICE:
·

Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.

·

Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.

·

Do not drop the brake pedal stroke sensor assembly.

·

If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.



HINT:

The nuts will be fully tightened when adjusting the brake pedal stroke sensor assembly.



iii.

Connect the connector.



Hide 3.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 89510D 4.ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY

Z101186

NOTICE:

When the brake pedal stroke sensor assembly is being reused, perform the following procedure to adjust it.



a.
C442435N01
0.448,0.073 0.729,0.427 0.281,0.354 18 false i

i.

Read the stroke sensor value in the Data List.

Chassis > Brake Booster > Data List
Tester Display
Stroke Sensor
50003 466 207


b.
C447600N01
2.448,0.24 2.865,0.573 0.417,0.333 18 false ii 2.24,0.771 2.656,1.104 0.417,0.333 18 false i 2.563,1.302 2.979,1.635 0.417,0.333 18 false ii

i.

Turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.

Standard Voltage (without the brake pedal depressed):

0.8 to 1.2 V



ii.

Tighten the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Do not depress the brake pedal after turning the ignition switch to ON.




Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Z101186

CAUTION:
B422343

·

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




Click hereGeneral>MAINTENANCE>AUXILIARY BATTERY>REMOVAL

Hide 73900 6.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 7.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 9. CHECK AND CLEAR DTC

Hide 10. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART