These DTCs are stored when a malfunction occurs in the telephone antenna assembly circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B15C111 | GNSS Antenna Circuit Short to Ground | Current to the telephone antenna assembly is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Short circuit) |
·
Telematics transceiver ·
Telephone antenna assembly ·
Antenna cord sub-assembly ·
No. 2 antenna cord sub-assembly |
Telematics | A |
| B15C113 | GNSS Antenna Circuit Open | Current to the telephone antenna assembly is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Open circuit) |
·
Telematics transceiver ·
Telephone antenna assembly ·
Antenna cord sub-assembly ·
No. 2 antenna cord sub-assembly |
Telematics | A |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION
When replacing the telematics transceiver, make sure to replace it with a new one.
Pre-procedure1
Turn the ignition switch to ON and wait for 10 seconds.
Clear the DTCs.
Procedure1
Check for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Pre-procedure1
Disconnect the antenna connector from the telephone antenna assembly.
Disconnect the antenna connector from the antenna cord sub-assembly.
Procedure1
| *a | Front view of wire harness connector
(to Telephone Antenna Assembly) |
| *b | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-2 - B-4 | Always | Below 1 Ω |
| A-2a - B-4a | Always | Below 1 Ω |
| A-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
Disconnect the antenna connector from the telematics transceiver.
Procedure1
| *a | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Telematics Transceiver) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-4 - ANT2-[1](GPS) | Always | Below 1 Ω |
| B-4a - ANT2-[1a] | Always | Below 1 Ω |
| B-4 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel)>REMOVAL
Pre-procedure1
Replace the telephone antenna assembly with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL
Clear the DTCs.
Procedure1
Recheck for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
B
Replace the telematics transceiver with a new one.
| Proceed to |
|---|
| NEXT |
NEXT