Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF SUNSHADE SYSTEM
RM37H0E _58 Vehicle Interior _095304 INTERIOR PANELS / TRIM _0454452 ROOF SUNSHADE SYSTEM Y

INTERIOR PANELS / TRIM  ROOF SUNSHADE SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the roof sunshade system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Driving conditions, weather conditions
How did it happen? Problem symptoms



Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the auxiliary battery voltage.

Standard voltage:

11 to 14 V


HINT:
·

A simple method to determine whether the battery is discharged is to operate the horn.

·

If the voltage is below 11 V, recharge or replace the battery before proceeding.




b.

Check the fuses and relays.


c.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

4.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
4.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the LIN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

5.CHECK FOR DTC*

B

5.CHECK FOR DTC*
a.

Check for DTCs and make a note of any codes that are output.

Body Electrical > Sliding Roof > Trouble Codes
50001 147

b.

Clear the DTCs.

Body Electrical > Sliding Roof > Clear DTCs
50002 147

c.

Recheck for DTCs.

Body Electrical > Sliding Roof > Trouble Codes
50001 147

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

6.PROBLEM SYMPTOMS TABLE

B

6.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in problem symptoms table A
Fault is listed in problem symptoms table B



A

7.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

7.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

8.ADJUST, REPAIR OR REPLACE
8.ADJUST, REPAIR OR REPLACE
a.

Check if the sliding roof drive gear sub-assembly has been replaced, or the sliding roof housing sub-assembly has been adjusted, or removed and installed.


Result:
Result Proceed to
The sliding roof drive gear sub-assembly has been replaced, or the sliding roof housing sub-assembly has been adjusted, or removed and installed. A
The sliding roof drive gear sub-assembly has not been replaced, and the sliding roof housing sub-assembly has not been adjusted, or removed and installed. B



A

9.INITIALIZE ROOF SUNSHADE SYSTEM

B

10.CONFIRMATION TEST
9.INITIALIZE ROOF SUNSHADE SYSTEM
a.

Initialize the sliding roof drive gear sub-assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>INITIALIZATION

HINT:

If initialization has not been performed, the auto operation and jam protection function will not operate or will operate incorrectly.



Result:
Proceed to
NEXT



NEXT

10.CONFIRMATION TEST
10.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END