Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF SUNSHADE SYSTEM
RM37H0E _58 Vehicle Interior _095304 INTERIOR PANELS / TRIM _0454452 ROOF SUNSHADE SYSTEM J

INTERIOR PANELS / TRIM  ROOF SUNSHADE SYSTEM  Roof Sunshade does not Move by Operating Roof Sunshade Switch  


DESCRIPTION

The sliding roof drive gear sub-assembly receives switch signals and drives its built-in motor.

WIRING DIAGRAM

E283517E13
4.792,4.021 6.646,4.344 1.854,0.323 10 false H4 4.781,4.177 7.156,4.646 2.375,0.469 10 false Sliding Roof Drive Gear Sub-assembly 1.969,3.313 3.823,3.635 1.854,0.323 10 false H8 1.969,3.469 3.406,4.094 1.438,0.625 10 false Roof Sunshade Switch (Map Light Assembly) 3.01,2.729 4.865,3.052 1.854,0.323 10 false CLS 3,2.281 4.854,2.604 1.854,0.323 10 false OPN 2.073,2.271 3.927,2.594 1.854,0.323 10 false GND 1.76,2.25 2.104,2.583 0.344,0.333 10 false 19 3.396,2.26 3.719,2.5 0.323,0.24 10 false 11 3.375,2.719 3.667,3.104 0.292,0.385 10 false 12 5.417,3.219 5.667,3.604 0.25,0.385 10 false 2 5.406,2.75 5.552,3.135 0.146,0.385 10 false 9 5.406,2.24 5.552,2.625 0.146,0.385 10 false 5 5.438,1.229 5.583,1.615 0.146,0.385 10 false 6 5.438,0.552 5.729,0.927 0.292,0.375 10 false 1 5.656,3.323 6.135,3.688 0.479,0.365 10 false E 5.656,2.833 6.135,3.198 0.479,0.365 10 false CLS 5.667,2.354 6.146,2.719 0.479,0.365 10 false OPN 5.667,1.354 6.146,1.719 0.479,0.365 10 false IG 5.667,0.625 6.146,0.99 0.479,0.365 10 false B 1.479,1.333 3.427,1.865 1.948,0.531 10 false from IG1 D NO.1 Relay*1 3.938,1.531 5.198,2.083 1.26,0.552 10 false IG1 D NO.2*1 1.833,0.635 3.583,1.125 1.75,0.49 10 false from Auxiliary Battery 3.969,0.823 5.135,1.365 1.167,0.542 10 false S/ROOF NO.1 1.479,1.656 3.427,2.188 1.948,0.531 10 false from IG1 P NO.1 Relay*2 3.938,1.823 5.198,2.375 1.26,0.552 10 false IG1 P NO.2*2 0.344,4.135 2.094,4.625 1.75,0.49 10 false *1: for LHD 0.344,4.417 2.104,4.813 1.76,0.396 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When the sliding roof drive gear sub-assembly is removed and reinstalled or replaced, it requires initialization.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>INITIALIZATION

·

The roof sunshade system uses the LIN communication system. First, confirm that there are no malfunctions in the LIN communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When a sliding roof drive gear sub-assembly DTC is output, first perform troubleshooting for the sliding roof drive gear sub-assembly DTC.



PROCEDURE

1.READ VALUE USING GTS
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF SUNSHADE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Sliding Roof > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Open Switch Open switch signal ON or OFF ON: Open switch pressed
OFF: Open switch not pressed
-
Close Switch Close switch signal ON or OFF ON: Close switch pressed
OFF: Close switch not pressed
-
Body Electrical > Sliding Roof > Data List
Tester Display
Open Switch
Close Switch
50003 147 1,4
OK:

The GTS display changes according to switch operation as shown in the table.



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

NG

2.INSPECT MAP LIGHT ASSEMBLY
2.INSPECT MAP LIGHT ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY - ROOF SUNSHADE SWITCH [MAP LIGHT ASSEMBLY])

NG

REPLACE ROOF SUNSHADE SWITCH (MAP LIGHT ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY - ROOF SUNSHADE SWITCH [MAP LIGHT ASSEMBLY])
a.

Disconnect the H4 sliding roof drive gear sub-assembly connector.


b.

Disconnect the H8 roof sunshade switch (map light assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H4,H8)Location & Routing

Click Connector(H4)Body>No. 1 Roof Wire>Sliding Roof Control ECU (Sliding Roof Drive Gear Sub-Assembly)

Click Connector(H8)Body>No. 1 Roof Wire>Map Light Assembly

H4-9 (CLS) - H8-12 (CLS) Always Below 1 Ω
H4-5 (OPN) - H8-11 (OPN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ROOF SUNSHADE SWITCH [MAP LIGHT ASSEMBLY] - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ROOF SUNSHADE SWITCH [MAP LIGHT ASSEMBLY] - BODY GROUND)
a.

Disconnect the H8 roof sunshade switch (map light assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H8)Location & Routing

Click Connector(H8)Body>No. 1 Roof Wire>Map Light Assembly

H8-19 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR