Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › PEDESTRIAN PROTECTION SYSTEM
RM37H0E _58 Vehicle Interior _095287 SUPPLEMENTAL RESTRAINT SYSTEMS _0454682 PEDESTRIAN PROTECTION SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  PEDESTRIAN PROTECTION SYSTEM  SRS Warning Light Remains ON  


DESCRIPTION

The pop up hood warning light is located in the combination meter assembly.

When the SRS is normal, the pop up hood warning light comes on for approximately 6 seconds after the ignition switch is turned from off to to ON, and then goes off automatically.

If there is a malfunction in the SRS, the pop up hood warning light comes on to inform the driver of a problem.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag ECU assembly in case the source voltage drops.

When the auxiliary battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.

A malfunction in this circuit is not recorded in the airbag ECU assembly. The pop up hood warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the pop up hood warning light is transmitted from the airbag ECU assembly to the combination meter assembly through the CAN communication system.

WIRING DIAGRAM

C414924E05
0.573,1.521 1.792,1.698 1.219,0.177 10 false from IG2 D Relay 2.969,1.531 4.198,1.729 1.229,0.198 10 false IG+ 2.698,1.427 2.927,1.615 0.229,0.188 10 false 21 2.083,1.719 2.875,1.906 0.792,0.188 10 false IG2 D NO.1 4.896,0.75 5.5,0.958 0.604,0.208 10 false A/BAG 3.26,0.583 4.49,0.781 1.229,0.198 10 false from IG2 P Relay 5.74,0.604 6.115,0.813 0.375,0.208 10 false IG2 5.438,0.49 6.667,0.688 1.229,0.198 10 false 36 5.458,1.979 6.688,2.177 1.229,0.198 10 false 33 5.427,2.365 6.656,2.563 1.229,0.198 10 false 32 2.99,2.469 4.219,2.667 1.229,0.198 10 false ES 0.615,3.292 2.469,3.448 1.854,0.156 10 false : CAN Communication Line 2.479,3 4.458,3.229 1.979,0.229 10 false Combination Meter Assembly 2.479,2.844 3.708,3.042 1.229,0.198 10 false D41 5.354,2.823 6.583,3.021 1.229,0.198 10 false D10 5.375,2.979 6.844,3.26 1.469,0.281 10 false Airbag ECU Assembly 5.74,2.094 6.135,2.26 0.396,0.167 10 false E1 5.74,2.458 6.104,2.635 0.365,0.177 10 false E2 2.708,2.354 2.906,2.531 0.198,0.177 10 false 31

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CHECK POP UP HOOD WARNING LIGHT
a.

Turn the ignition switch to ON and check the pop up hood warning light condition.

HINT:

The primary check is performed for approximately 6 seconds after the ignition switch is turned to ON.



Result:
Result Proceed to
After the primary check period, the pop up hood warning light remains on. A
After the primary check period, the pop up hood warning light goes off and comes on again. B



A

2.CHECK AUXILIARY BATTERY VOLTAGE

B

7.CHECK CAN COMMUNICATION SYSTEM
2.CHECK AUXILIARY BATTERY VOLTAGE
a.

Measure the auxiliary battery voltage with the ignition switch off.

Standard voltage:

11 to 14 V


HINT:

It may be possible to tell whether the auxiliary battery is discharged by operating the horn.

If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.



Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION OF CONNECTORS

NG

REPLACE OR RECHARGE AUXILIARY BATTERY

3.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


c.

Check that the connector is properly connected to the airbag ECU assembly.

OK:

The connector is properly connected.



Result:
Proceed to
OK
NG



OK

4.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

4.CHECK CONNECTORS
a.
C414926C01
0.656,1.49 0.969,1.688 0.313,0.198 10 false *1 2.594,1.635 2.906,1.833 0.313,0.198 10 false *2 1.604,1.24 1.917,1.438 0.313,0.198 10 false *3
*1 Combination Meter Assembly
*2 Airbag ECU Assembly
*3 Wire Harness


Disconnect the airbag ECU assembly connector.


b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



c.

Check that the connectors are not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CONNECTOR

5.CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Operate all components of the electrical systems (defogger, wipers, headlights, heater blower, etc.).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D10)Location & Routing

Click Connector(D10)Instrument Panel>Instrument Panel Wire>Airbag ECU Assembly

D10-36 (IG2) - Body ground Ignition switch ON 8 to 16 V



e.

Turn the ignition switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D10)Location & Routing

Click Connector(D10)Instrument Panel>Instrument Panel Wire>Airbag ECU Assembly

D10-33 (E1)- Body ground Always Below 1 Ω
D10-32 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK POP UP HOOD WARNING LIGHT

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

6.CHECK POP UP HOOD WARNING LIGHT
a.
C414926C01
0.656,1.49 0.969,1.688 0.313,0.198 10 false *1 2.594,1.635 2.906,1.833 0.313,0.198 10 false *2 1.604,1.24 1.917,1.438 0.313,0.198 10 false *3
*1 Combination Meter Assembly
*2 Airbag ECU Assembly
*3 Wire Harness


Turn the ignition switch to ON and check the pop up hood warning light condition.

OK:

After the primary check period, the pop up hood warning light turns off for approximately 10 seconds and then turns back on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY

7.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are output A
DTC is not output B



A

B

8.CHECK AUXILIARY BATTERY
8.CHECK AUXILIARY BATTERY
a.

Measure the auxiliary battery voltage with the ignition switch off.

Standard voltage:

11 to 14 V


HINT:

It may be possible to tell whether the auxiliary battery is discharged by operating the horn.

If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.



Result:
Proceed to
OK
NG



OK

9.CHECK CONNECTION OF CONNECTORS

NG

REPLACE OR RECHARGE AUXILIARY BATTERY

9.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


c.

Check that the connector is properly connected to the airbag ECU assembly.

OK:

The connector is properly connected.



Result:
Proceed to
OK
NG



OK

10.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

10.CHECK CONNECTORS
a.
C414926C01
0.656,1.49 0.969,1.688 0.313,0.198 10 false *1 2.594,1.635 2.906,1.833 0.313,0.198 10 false *2 1.604,1.24 1.917,1.438 0.313,0.198 10 false *3
*1 Combination Meter Assembly
*2 Airbag ECU Assembly
*3 Wire Harness


Disconnect the airbag ECU assembly connector.


b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



c.

Check that the connectors are not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CONNECTOR

11.CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


c.

Operate all components of the electrical systems (defogger, wipers, headlights, heater blower, etc.).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D10)Location & Routing

Click Connector(D10)Instrument Panel>Instrument Panel Wire>Airbag ECU Assembly

D10-36 (IG2) - Body ground Ignition switch ON 8 to 16 V



e.

Turn the ignition switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D10)Location & Routing

Click Connector(D10)Instrument Panel>Instrument Panel Wire>Airbag ECU Assembly

D10-33 (E1) - Body ground Always Below 1 Ω
D10-32 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK CONNECTOR

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

12.CHECK CONNECTOR
a.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


b.

Check that the connector is properly connected to the combination meter assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not properly connected, reconnect the connector and proceed to the next inspection.



c.

Disconnect the connector from the combination meter assembly.


d.

Check that the terminals of the connector are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D41)Location & Routing

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D41-21 (IG+) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D41)Location & Routing

Click Connector(D41)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D41-31 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

14.CHECK POP UP HOOD WARNING LIGHT

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

14.CHECK POP UP HOOD WARNING LIGHT
a.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


b.

Connect the connector to the combination meter assembly.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON and check the pop up hood warning light condition.

OK:

After the primary check period, the pop up hood warning light turns off for approximately 10 seconds and then turns back on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY