Home › Drivetrain › Q710 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM
RM37H0E _52 Drivetrain _093826 Q710 HYBRID TRANSMISSION / TRANSAXLE _0454877 ELECTRONIC SHIFT LEVER SYSTEM C

Q710 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  P085D94  Gear Shift Control Module "A" Unexpected Operation  


DESCRIPTION

The shift control ECU monitors its internal operation. When it detects an internal malfunction, the DTC is stored in the EV control ECU.

The cause of this malfunction may be one of the following:

Shift control ECU internal malfunction
·

Shift control ECU malfunction


Vehicle speed sensor circuit malfunction
·

Discrepancy between motor resolver signal and actual vehicle speed


DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P085D94 Gear Shift Control Module "A" Unexpected Operation ECU internal malfunction (system monitoring malfunction) continuously occurs for 10 seconds or more
(1 trip detection logic)
Shift control ECU
·

Master Warning

-

Comes on


·

Multi-information Display Error Message

-

Displayed



EV A

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the All Readiness check procedure.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>UTILITY


1.

Turn the ignition switch to ON (READY).

2.

With the brake pedal depressed, move the shift lever as follows to select each shift state: R → D.

3.

Drive the vehicle at 40 km/h (25 mph) or more for 10 seconds or more.

4.

Stop the vehicle. With the brake pedal depressed, move the shift lever as follows to select each shift state: Br → N.

5.

Push the P position switch (parking switch) to select park (P).


CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a shift control supply. Therefore, ensure there is no power being supplied to the vehicle when disconnecting or reconnecting the connector of the shift control ECU and when removing or installing the shift control ECU.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
No DTCs in the table below are output A
P085D94 and any DTCs in the table below are output B


Priority Relevant DTC
1 U110700 Lost Communication with Power Management Module (Gear Shift Control Module "A")
2 P0A3F16 Drive Motor "A" Position Sensor Circuit Voltage Below Threshold
P0A3F1C Drive Motor "A" Position Sensor Circuit Voltage Out of Range
P0A3F22 Drive Motor "A" Position Sensor Signal Amplitude > Maximum

HINT:

The chart above is listed in inspection order of priority.



Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK FREEZE FRAME DATA

B

GO TO DTC CHART

2.CHECK FREEZE FRAME DATA

Pre-procedure1

a.

Turn the ignition switch to ON.


Procedure1

a.

Read the freeze frame data of DTC P085D94.

Powertrain > EV > Trouble Codes
50001 397
Powertrain > EV > DTC(P085D94) > Freeze Frame Data
Tester Display
Vehicle Speed
FR Wheel Speed
FL Wheel Speed
50040 397 12,104,105 P085D94
Result:
Result Proceed to
Vehicle was stopped ("FR Wheel Speed" and "FL Wheel Speed" are between 0 and 1.4 km/h (0 and 1 mph)) but "Vehicle Speed" was 3 km/h (2 mph) or more A
Vehicle was stopped ("FR Wheel Speed" and "FL Wheel Speed" are between 0 and 1.4 km/h (0 and 1 mph)) and "Vehicle Speed" was less than 3 km/h (2 mph) B



Post-procedure1

a.

Turn the ignition switch off.



A

3.CHECK MOTOR RESOLVER CIRCUIT

B

3.CHECK MOTOR RESOLVER CIRCUIT

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS