Home › Drivetrain › Q710 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM
RM37H0E _52 Drivetrain _093826 Q710 HYBRID TRANSMISSION / TRANSAXLE _0454877 ELECTRONIC SHIFT LEVER SYSTEM C

Q710 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  P08A600  Gear Lever Position Sensor Correlation Failure  P08A662  Gear Lever Position Sensor Signal Compare Failure  P183411  Gear Lever Y Position Sensor 1 Circuit Short to Ground  P183415  Gear Lever Y Position Sensor 1 Circuit Short to Auxiliary Battery or Open  P183A11  Gear Lever Y Position Sensor 2 Circuit Short to Ground  P183A15  Gear Lever Y Position Sensor 2 Circuit Short to Auxiliary Battery or Open  P183F12  Gear Lever X Position Sensor 1 Circuit Short to Auxiliary Battery  P183F14  Gear Lever X Position Sensor 1 Circuit Short to Ground or Open  P184512  Gear Lever X Position Sensor 2 Circuit Short to Auxiliary Battery  P184514  Gear Lever X Position Sensor 2 Circuit Short to Ground or Open  


DESCRIPTION

HINT:
·

The electronic shift lever system is a linkless type that does not use a shift cable.

·

The shift and select sensors are non-contact type sensors.



The shift lever (shift lock control unit assembly) is a momentary type, which returns to its home position by spring tension as the driver's hand is released from the shift lever after shifting.

The shift lever (shift lock control unit assembly) contains a shift lever position sensor to detect the shift lever position (Home, R, N, D or Br). Because the shift lever position sensor operates using Hall ICs, they can accurately detect the shift lever position in a reliable manner.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P08A600 Gear Lever Position Sensor Correlation Failure The ignition switch is ON and shift sensor pattern malfunction (VSI1, VSI2, VSI3 and VSI4 High/Low combination malfunction) continuously occurs for 3 seconds or more
(1 trip detection logic)
·

Shift lock control unit assembly

·

Shift control ECU

·

Wire harness or connector


·

Master Warning

-

Comes on


·

Multi-information Display Error Message

-

Displayed



EV A
P08A662 Gear Lever Position Sensor Signal Compare Failure The ignition switch is ON and auxiliary battery voltage is 10 V or higher, shift sensor pattern malfunction (VSI1, VSI2, VSI3 or VSI4 value outside specified range) continuously occurs for 3 seconds or more
(1 trip detection logic)
·

Shift lock control unit assembly

·

Shift control ECU

·

Wire harness or connector


·

Master Warning

-

Comes on


·

Multi-information Display Error Message

-

Displayed



EV A
P183411 Gear Lever Y Position Sensor 1 Circuit Short to Ground The ignition switch is ON and auxiliary battery voltage is 10 V or higher, VSI1 terminal voltage is below 0.3 V continuously for 3 seconds or more
(1 trip detection logic)
·

Shift lock control unit assembly

·

Shift control ECU

·

Wire harness or connector


·

Master Warning

-

Comes on


·

Multi-information Display Error Message

-

Displayed



EV A
P183415 Gear Lever Y Position Sensor 1 Circuit Short to Auxiliary Battery or Open The ignition switch is ON and auxiliary battery voltage is 10 V or higher, VSI1 terminal voltage is higher than 4.68 V continuously for 3 seconds or more
(1 trip detection logic)
·

Shift lock control unit assembly

·

Shift control ECU

·

Wire harness or connector


·

Master Warning

-

Comes on


·

Multi-information Display Error Message

-

Displayed



EV A
P183A11 Gear Lever Y Position Sensor 2 Circuit Short to Ground The ignition switch is ON and auxiliary battery voltage is 10 V or higher, VSI2 terminal voltage is below 0.6 V continuously for 3 seconds or more
(1 trip detection logic)
·

Shift lock control unit assembly

·

Shift control ECU

·

Wire harness or connector


·

Master Warning

-

Comes on


·

Multi-information Display Error Message

-

Displayed



EV A
P183A15 Gear Lever Y Position Sensor 2 Circuit Short to Auxiliary Battery or Open The ignition switch is ON and auxiliary battery voltage is 10 V or higher, VSI2 terminal voltage is higher than 4.4 V continuously for 3 seconds or more
(1 trip detection logic)
·

Shift lock control unit assembly

·

Shift control ECU

·

Wire harness or connector


·

Master Warning

-

Comes on


·

Multi-information Display Error Message

-

Displayed



EV A
P183F12 Gear Lever X Position Sensor 1 Circuit Short to Auxiliary Battery The ignition switch is ON and auxiliary battery voltage is 10 V or higher, VSI3 terminal voltage is higher than 4.4 V continuously for 3 seconds or more
(1 trip detection logic)
·

Shift lock control unit assembly

·

Shift control ECU

·

Wire harness or connector


·

Master Warning

-

Comes on


·

Multi-information Display Error Message

-

Displayed



EV A
P183F14 Gear Lever X Position Sensor 1 Circuit Short to Ground or Open The ignition switch is ON and auxiliary battery voltage is 10 V or higher, VSI3 terminal voltage is below 0.6 V continuously for 3 seconds or more
(1 trip detection logic)
·

Shift lock control unit assembly

·

Shift control ECU

·

Wire harness or connector


·

Master Warning

-

Comes on


·

Multi-information Display Error Message

-

Displayed



EV A
P184512 Gear Lever X Position Sensor 2 Circuit Short to Auxiliary Battery The ignition switch is ON and auxiliary battery voltage is 10 V or higher, VSI4 terminal voltage is higher than 4.68 V continuously for 3 seconds or more
(1 trip detection logic)
·

Shift lock control unit assembly

·

Shift control ECU

·

Wire harness or connector


·

Master Warning

-

Comes on


·

Multi-information Display Error Message

-

Displayed



EV A
P184514 Gear Lever X Position Sensor 2 Circuit Short to Ground or Open The ignition switch is ON and auxiliary battery voltage is 10 V or higher, VSI4 terminal voltage is below 0.3 V continuously for 3 seconds or more
(1 trip detection logic)
·

Shift lock control unit assembly

·

Shift control ECU

·

Wire harness or connector


·

Master Warning

-

Comes on


·

Multi-information Display Error Message

-

Displayed



EV A

Shift lever position sensor pattern malfunctions are detected when a logical inconsistency is detected by comparing each shift lever position sensor signal with the determined shift position. The detection pattern is as follows:

Shift Lever Position Sensor Correlation Failure (P08A600)
Shift Lever Position Sensor Signal VSI1 VSI2 VSI3 VSI4 Malfunction Detection
Input Voltage Low Low High High Normal
High High Low Low Normal
Low High Low High Abnormal
High Low High Low Abnormal

HINT:
·

Low: below 2.5 V

·

High: 2.5 V or higher



Shift Lever Position Sensor Signal Compare Failure (P08A662)
Shift Lever Position Sensor Signal Input Voltage Malfunction Detection
VSI1 ←→ VSI2 Voltage difference 0.742 V or higher Abnormal
VSI2 ←→ VSI3 Voltage difference 1.952 V or higher Abnormal
VSI3 ←→ VSI4 Voltage difference 0.742 V or higher Abnormal
VSI1 ←→ VSI3 Voltage difference 2.502 V or higher Abnormal
VSI2 ←→ VSI4 Voltage difference 2.502 V or higher Abnormal
VSI1 ←→ VSI4 Voltage difference 3.052 V or higher Abnormal

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the All Readiness check procedure.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>UTILITY


1.

Turn the ignition switch to ON (READY).

2.

With the brake pedal depressed, slowly move the shift lever as follows to select each shift state: N → R → N → D → Br → Home.

3.

Push the P position switch (parking switch) to select park (P).


WIRING DIAGRAM

C375692E08
2.542,0.771 3.156,0.969 0.615,0.198 10 false VCX1 2.521,1.167 3.135,1.365 0.615,0.198 10 false VCX2 2.552,1.563 3.167,1.76 0.615,0.198 10 false VSX1 2.531,2.74 3.146,2.938 0.615,0.198 10 false VSX2 2.531,3.958 3.146,4.156 0.615,0.198 10 false VSX3 2.531,5.156 3.146,5.354 0.615,0.198 10 false VSX4 2.573,5.552 3.188,5.75 0.615,0.198 10 false E2X1 2.552,5.958 3.167,6.156 0.615,0.198 10 false E2X2 5.01,0.781 5.625,0.979 0.615,0.198 10 false VCX1 5.01,1.156 5.625,1.354 0.615,0.198 10 false VCX2 5.01,1.552 5.625,1.75 0.615,0.198 10 false VSI1 5.021,2.74 5.635,2.938 0.615,0.198 10 false VSI2 5.021,3.969 5.635,4.167 0.615,0.198 10 false VSI3 5.021,5.156 5.635,5.354 0.615,0.198 10 false VSI4 5.01,5.552 5.625,5.75 0.615,0.198 10 false E2X1 5.01,5.969 5.625,6.167 0.615,0.198 10 false E2X2 3.01,0.781 3.417,1 0.406,0.219 10 false 4 3,1.156 3.406,1.375 0.406,0.219 10 false 12 3.01,1.552 3.417,1.771 0.406,0.219 10 false 7 3.01,2.74 3.417,2.958 0.406,0.219 10 false 5 4.729,0.771 4.958,0.979 0.229,0.208 10 false 20 3,3.958 3.406,4.177 0.406,0.219 10 false 11 3.01,5.156 3.417,5.375 0.406,0.219 10 false 9 3,5.552 3.406,5.771 0.406,0.219 10 false 14 3.01,5.958 3.417,6.177 0.406,0.219 10 false 2 4.729,1.156 4.958,1.365 0.229,0.208 10 false 22 4.729,1.563 4.958,1.75 0.229,0.188 10 false 19 4.75,2.75 4.979,2.938 0.229,0.188 10 false 21 4.729,3.969 4.958,4.156 0.229,0.188 10 false 23 4.729,5.167 4.958,5.354 0.229,0.188 10 false 25 4.719,5.563 4.948,5.75 0.229,0.188 10 false 24 4.719,5.958 4.948,6.146 0.229,0.188 10 false 26 0.885,6.417 2.667,6.594 1.781,0.177 10 false Shift Lever Position Sensor 0.417,7.188 2.771,7.573 2.354,0.385 10 false Shift Lever Position Sensor (Shift Lock Control Unit Assembly) 0.417,6.979 0.875,7.177 0.458,0.198 10 false D16 4.896,6.906 5.354,7.104 0.458,0.198 10 false D93 4.906,7.125 6.146,7.323 1.24,0.198 10 false Shift Control ECU

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The vehicle is equipped with a shift control supply. Therefore, ensure there is no power being supplied to the vehicle when disconnecting or reconnecting the connector of the shift control ECU and when removing or installing the shift control ECU.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>PRECAUTION



PROCEDURE

1.READ VALUE USING GTS (SHIFT LEVER POSITION SENSOR VOLTAGE)

Pre-procedure1

a.

Turn the ignition switch to ON (READY).


Procedure1

a.

With the brake pedal depressed, slowly move the shift lever as follows: N → R → N → D → Br → Home.

HINT:

Wait with the shift lever in each position for 5 seconds or more.



b.

Read the Data List according to the display on the GTS.

Result:
Data List Item Shift Lever Position
D N R Br Home
Shift Sensor Voltage (VSI1) (Gear Shift Control Module) 1.395 to 1.923 V 0.745 to 1.395 V 0.3 to 0.745 V 2.5 to 3.605 V 3.605 to 4.255 V
Shift Sensor Voltage (VSI2) (Gear Shift Control Module) 2.08 to 2.5 V 1.295 to 2.08 V 0.3 to 1.295 V 2.5 to 3.055 V 3.055 to 3.705 V
Shift Sensor Voltage (VSI3) (Gear Shift Control Module) 3.705 to 4.75 V 2.92 to 3.705 V 2.5 to 2.92 V 0.3 to 1.295 V 1.295 to 1.945 V
Shift Sensor Voltage (VSI4) (Gear Shift Control Module) 4.255 to 4.75 V 3.605 to 4.255 V 3.077 to 3.605 V 0.3 to 0.745 V 0.745 to 1.395 V


Powertrain > EV > Data List
Tester Display
Shift Sensor Voltage (VSI1) (Gear Shift Control Module)
Shift Sensor Voltage (VSI2) (Gear Shift Control Module)
Shift Sensor Voltage (VSI3) (Gear Shift Control Module)
Shift Sensor Voltage (VSI4) (Gear Shift Control Module)
50003 397 579,580,581,582

Result:
Proceed to
OK
NG


Post-procedure1

a.

Push the P position switch (parking switch) to select park (P).


b.

Turn the ignition switch off.



OK

NG

2.CHECK HARNESS AND CONNECTOR ((SHIFT CONTROL ECU - SHIFT LEVER POSITION SENSOR (SHIFT LOCK CONTROL UNIT ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR ((SHIFT CONTROL ECU - SHIFT LEVER POSITION SENSOR (SHIFT LOCK CONTROL UNIT ASSEMBLY))

Pre-procedure1

a.

Disconnect the D93 shift control ECU connector.


b.

Disconnect the D16 shift lever position sensor (shift lock control unit assembly) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D93,D16)Location & Routing

Click Connector(D93)Instrument Panel>Instrument Panel Wire>Shift Control ECU

Click Connector(D16)Instrument Panel>Instrument Panel Wire>Shift Lock Control Unit Assembly

D93-20 (VCX1) - D16-4 (VCX1) Always Below 1 Ω
D93-22 (VCX2) - D16-12 (VCX2) Always Below 1 Ω
D93-19 (VSI1) - D16-7 (VSX1) Always Below 1 Ω
D93-21 (VSI2) - D16-5 (VSX2) Always Below 1 Ω
D93-23 (VSI3) - D16-11 (VSX3) Always Below 1 Ω
D93-25 (VSI4) - D16-9 (VSX4) Always Below 1 Ω
D93-24 (E2X1) - D16-14 (E2X1) Always Below 1 Ω
D93-26 (E2X2) - D16-2 (E2X2) Always Below 1 Ω
D93-20 (VCX1) or D16-4 (VCX1) - Body ground and other terminals Always 10 kΩ or higher
D93-22 (VCX2) or D16-12 (VCX2) - Body ground and other terminals Always 10 kΩ or higher
D93-19 (VSI1) or D16-7 (VSX1) - Body ground and other terminals Always 10 kΩ or higher
D93-21 (VSI2) or D16-5 (VSX2) - Body ground and other terminals Always 10 kΩ or higher
D93-23 (VSI3) or D16-11 (VSX3) - Body ground and other terminals Always 10 kΩ or higher
D93-25 (VSI4) or D16-9 (VSX4) - Body ground and other terminals Always 10 kΩ or higher
D93-24 (E2X1) or D16-14 (E2X1) - Body ground and other terminals Always 10 kΩ or higher
D93-26 (E2X2) or D16-2 (E2X2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the D16 shift lever position sensor (shift lock control unit assembly) connector.


b.

Reconnect the D93 shift control ECU connector.



OK

3.CHECK SHIFT CONTROL ECU (VCX1, VCX2 VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SHIFT CONTROL ECU (VCX1, VCX2 VOLTAGE)

Pre-procedure1

a.

Disconnect the D16 shift lever position sensor (shift lock control unit assembly) connector.


b.

Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D16)Location & Routing

Click Connector(D16)Instrument Panel>Instrument Panel Wire>Shift Lock Control Unit Assembly

D16-4 (VCX1) - D16-14 (E2X1) Ignition switch ON 4.5 to 5.5 V
D16-12 (VCX2) - D16-2 (E2X2) Ignition switch ON 4.5 to 5.5 V


NOTICE:

Turning the ignition switch to ON with the connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the D16 shift lever position sensor (shift lock control unit assembly) connector.



OK

4.CHECK SHIFT CONTROL ECU (VSI1, VSI2, VSI3, VSI4 VOLTAGE)

NG

4.CHECK SHIFT CONTROL ECU (VSI1, VSI2, VSI3, VSI4 VOLTAGE)

Pre-procedure1

a.
C377811C17
2.406,0.25 2.844,0.469 0.438,0.219 3,1.594 2.865,1.01 true 2.74,1.875 2.74,1.01 true 1.688,1.594 2.333,1.01 true 1.021,1.854 2.25,1 true 1.938,1.865 2.385,1.01 true 2.365,1.594 2.458,1.01 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 2.5,0.292 2.958,0.49 0.458,0.198 10 false D93 2.802,1.635 3.427,1.792 0.625,0.156 10 false 19 (VSI1) 2.49,1.906 3.083,2.073 0.594,0.167 10 false 21 (VSI2) 2.083,1.646 2.698,1.802 0.615,0.156 10 false 23 (VSI3) 1.354,1.635 1.969,1.792 0.615,0.156 10 false 25 (VSI4) 0.646,1.906 1.313,2.073 0.667,0.167 10 false 26 (E2X2) 1.646,1.917 2.281,2.083 0.635,0.167 10 false 24 (E2X1)
*a Component with harness connected
(Shift Control ECU)


Turn the ignition switch to ON.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(D93)Location & Routing

Click Connector(D93)Instrument Panel>Instrument Panel Wire>Shift Control ECU

D93-19 (VSI1) - D93-24 (E2X1) Ignition switch ON, shift lever in D 1.395 to 1.923 V
D93-19 (VSI1) - D93-24 (E2X1) Ignition switch ON, shift lever in N 0.745 to 1.395 V
D93-19 (VSI1) - D93-24 (E2X1) Ignition switch ON, shift lever in R 0.3 to 0.745 V
D93-19 (VSI1) - D93-24 (E2X1) Ignition switch ON, shift lever in Br 2.5 to 3.605 V
D93-19 (VSI1) - D93-24 (E2X1) Ignition switch ON, shift lever in home position 3.605 to 4.255 V
D93-21 (VSI2) - D93-24 (E2X1) Ignition switch ON, shift lever in D 2.08 to 2.5 V
D93-21 (VSI2) - D93-24 (E2X1) Ignition switch ON, shift lever in N 1.295 to 2.08 V
D93-21 (VSI2) - D93-24 (E2X1) Ignition switch ON, shift lever in R 0.3 to 1.295 V
D93-21 (VSI2) - D93-24 (E2X1) Ignition switch ON, shift lever in Br 2.5 to 3.055 V
D93-21 (VSI2) - D93-24 (E2X1) Ignition switch ON, shift lever in home position 3.055 to 3.705 V
D93-23 (VSI3) - D93-26 (E2X2) Ignition switch ON, shift lever in D 3.705 to 4.75 V
D93-23 (VSI3) - D93-26 (E2X2) Ignition switch ON, shift lever in N 2.92 to 3.705 V
D93-23 (VSI3) - D93-26 (E2X2) Ignition switch ON, shift lever in R 2.5 to 2.92 V
D93-23 (VSI3) - D93-26 (E2X2) Ignition switch ON, shift lever in Br 0.3 to 1.295 V
D93-23 (VSI3) - D93-26 (E2X2) Ignition switch ON, shift lever in home position 1.295 to 1.945 V
D93-25 (VSI4) - D93-26 (E2X2) Ignition switch ON, shift lever in D 4.255 to 4.75 V
D93-25 (VSI4) - D93-26 (E2X2) Ignition switch ON, shift lever in N 3.605 to 4.255 V
D93-25 (VSI4) - D93-26 (E2X2) Ignition switch ON, shift lever in R 3.077 to 3.605 V
D93-25 (VSI4) - D93-26 (E2X2) Ignition switch ON, shift lever in Br 0.3 to 0.745 V
D93-25 (VSI4) - D93-26 (E2X2) Ignition switch ON, shift lever in home position 0.745 to 1.395 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Turn the ignition switch off.



OK

NG

5.CHECK SHIFT CONTROL ECU (CHECK RESISTANCE)
5.CHECK SHIFT CONTROL ECU (CHECK RESISTANCE)

Pre-procedure1

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D16 shift lever position sensor (shift lock control unit assembly) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D16)Location & Routing

Click Connector(D16)Instrument Panel>Instrument Panel Wire>Shift Lock Control Unit Assembly

D16-7 (VSX1) - D16-4 (VCX1) or D16-12 (VCX2) 20°C (68°F) 35 to 43 kΩ
D16-5 (VSX2) - D16-4 (VCX1) or D16-12 (VCX2) 20°C (68°F) 35 to 43 kΩ
D16-11 (VSX3) - D16-14 (E2X1) or D16-2 (E2X2) 20°C (68°F) 35 to 43 kΩ
D16-9 (VSX4) - D16-14 (E2X1) or D16-2 (E2X2) 20°C (68°F) 35 to 43 kΩ



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the D16 shift lever position sensor (shift lock control unit assembly) connector.


b.

Reconnect the cable to the negative (-) auxiliary battery terminal.



OK

REPLACE TRANSMISSION FLOOR SHIFT ASSEMBLY

NG