Home › Drivetrain › Q710 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM
RM37H0E _52 Drivetrain _093826 Q710 HYBRID TRANSMISSION / TRANSAXLE _0454877 ELECTRONIC SHIFT LEVER SYSTEM C

Q710 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  P1761A2  Gear Shift Control Module "A" System Voltage Low  


DESCRIPTION

Auxiliary battery power is supplied to the BATT terminal of the shift control ECU. Back-up power is supplied even the ignition switch turned off.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1761A2 Gear Shift Control Module "A" System Voltage Low With auxiliary battery voltage 10 V or higher, BATT terminal voltage (ECU recognition value) is below 1 V continuously for 3 seconds or more
(1 trip detection logic)
·

Shift control ECU

·

Wire harness or connector


·

Master Warning

-

Comes on


·

Multi-information Display Error Message

-

Displayed



EV A

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the All Readiness check procedure.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>UTILITY


1.

Turn the ignition switch to ON and wait for 5 seconds or more.


WIRING DIAGRAM

C423963E06
5.646,2.906 6.802,3.115 1.156,0.208 10 false Shift Control ECU 1.094,1.927 2.438,2.219 1.344,0.292 10 false Auxiliary Battery 1.979,1.354 2.813,1.531 0.833,0.177 10 false R/B RR# 2 4.01,1.354 4.865,1.542 0.854,0.188 10 false P CON MAIN 5.479,1.198 5.938,1.396 0.458,0.198 10 false D93 5.552,0.979 5.708,1.177 0.156,0.198 10 false 1 5.5,2.177 5.958,2.375 0.458,0.198 10 false D92 5.552,1.958 5.708,2.156 0.156,0.198 10 false 1 5.885,1.188 6.375,1.344 0.49,0.156 10 false BATT 5.896,2.167 6.208,2.365 0.313,0.198 10 false E1 4.094,1.063 4.26,1.229 0.167,0.167 10 false 1 4.521,1.063 4.688,1.229 0.167,0.167 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The vehicle is equipped with a shift control supply. Therefore, ensure there is no power being supplied to the vehicle when disconnecting or reconnecting the connector of the shift control ECU and when removing or installing the shift control ECU.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (SHIFT CONTROL ECU CONNECTOR)
a.
for LHD:
C452170

for RHD:
C450295

Check the connector connections and contact pressure of the relevant terminals for the shift control ECU connectors.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connectors are connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK AUXILIARY BATTERY VOLTAGE

NG

CONNECT SECURELY

2.CHECK AUXILIARY BATTERY VOLTAGE

Pre-procedure1

a.

Disconnect the D93 shift control ECU connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D93)Location & Routing

Click Connector(D93)Instrument Panel>Instrument Panel Wire>Shift Control ECU

D93-1 (BATT) - Body ground Ignition switch off 8 to 15.4 V



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the D93 shift control ECU connector.



OK

NG

3.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - P CON MAIN FUSE)
3.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - P CON MAIN FUSE)

Pre-procedure1

a.

Disconnect the D93 shift control ECU connector.


b.

Remove the P CON MAIN fuse from the luggage room relay block.

C450339C02
5.063,0.24 5.427,0.49 0.365,0.25 4.219,0.906 4.729,1.042 true 0.688,0.229 1,0.427 0.313,0.198 10 false *1 2.531,1.25 2.844,1.448 0.313,0.198 10 false *2 4.052,0.125 4.365,0.323 0.313,0.198 10 false *a 3.854,0.792 4.26,0.969 0.406,0.177 10 false BATT 5.115,0.292 5.573,0.49 0.458,0.198 10 false D93
*1 Luggage Room Relay Block *2 P CON MAIN Fuse
*a Front view of wire harness connector
(to Shift Control ECU)
- -



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D93)Location & Routing

Click Connector(D93)Instrument Panel>Instrument Panel Wire>Shift Control ECU

P CON MAIN fuse terminal 2 - D93-1 (BATT) Always Below 1 Ω
P CON MAIN fuse terminal 2 or D93-1 (BATT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Reconnect the D93 shift control ECU connector.


b.

Install the P CON MAIN fuse.



OK

4.CHECK HARNESS AND CONNECTOR (P CON MAIN FUSE - AUXILIARY BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (P CON MAIN FUSE - AUXILIARY BATTERY)

Pre-procedure1

a.
C450340C02
0.125,0.083 0.438,0.281 0.313,0.198 10 false *1 2.323,1.406 2.635,1.604 0.313,0.198 10 false *2
*1 Luggage Room Relay Block
*2 P CON MAIN Fuse


Remove the P CON MAIN fuse from the luggage room relay block.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the cable from the positive (+) auxiliary battery terminal.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P CON MAIN fuse terminal 1 - Auxiliary battery positive (+) cable Always Below 1 Ω
P CON MAIN fuse terminal 1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

Connect the cable to the positive (+) auxiliary battery terminal.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Install the P CON MAIN fuse.



OK

5.CHARGE AUXILIARY BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHARGE AUXILIARY BATTERY
a.

Charge the auxiliary battery.


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT

Pre-procedure1

a.

Turn the ignition switch to ON.


Procedure1

a.

Check for DTCs and freeze frame data and then write them down.

Powertrain > EV > Trouble Codes
50001 397

Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch off.



NEXT

7.CLEAR DTC
7.CLEAR DTC

Pre-procedure1

a.

Turn the ignition switch to ON.


Procedure1

a.

Clear the DTCs.

Powertrain > EV > Clear DTCs
50002 397

Result:
Proceed to
NEXT


Post-procedure1

a.

Turn the ignition switch off.


b.

Leave the vehicle as is for 60 seconds or more.

NOTICE:
·

Do not connect the GTS.

·

Do not depress the brake pedal.

·

Do not open/close any of the doors.





NEXT

8.CHECK DTC OUTPUT (SIMULATION TEST)
8.CHECK DTC OUTPUT (SIMULATION TEST)

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 5 seconds or more.


Procedure1

a.

Check if DTCs are output.

Powertrain > EV > Trouble Codes
50001 397

Result:
Result Proceed to
P1761A2 is not output A
P1761A2 is output B


Post-procedure1

a.

Turn the ignition switch off.



A

END

B