Home › Drivetrain › Q710 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM
RM37H0E _52 Drivetrain _093826 Q710 HYBRID TRANSMISSION / TRANSAXLE _0454877 ELECTRONIC SHIFT LEVER SYSTEM J

Q710 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  "Stop vehicle in a safe place Push P switch" is Displayed on Multi-information Display  


CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The vehicle is equipped with a shift control supply. Therefore, ensure there is no power being supplied to the vehicle when disconnecting or reconnecting the connector of the shift control ECU and when removing or installing the shift control ECU.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK DTC OUTPUT (EV)
a.

Turn the ignition switch to ON.


b.

Depress the brake pedal and move the shift lever to select neutral (N).


c.

Push the P position switch (parking switch) to select park (P).


d.

Check if DTCs are output.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
None of the DTCs are output. A
Any of the DTCs are output. B



e.

Turn the ignition switch off.



A

2.CHECK OPERATION

B

GO TO DTC CHART

2.CHECK OPERATION
a.

Turn the ignition switch to ON.


b.

Depress the brake pedal and move the shift lever to select neutral (N).


c.

Check that if there is an error message displayed on the multi-information display.

Result:
Result Proceed to
Only "Stop vehicle in a safe place Push P switch" is displayed on the multi-information display. A
"Stop vehicle in a safe place Push P switch" and other error messages are displayed on the multi-information display simultaneously. B



d.

Push the P position switch (parking switch) to select park (P).


e.

Turn the ignition switch off.



A

3.READ VALUE USING GTS (BATT VOLTAGE FOR GEAR SHIFT CONTROL MODULE)

B

3.READ VALUE USING GTS (BATT VOLTAGE FOR GEAR SHIFT CONTROL MODULE)
a.

Turn the ignition switch to ON.


b.

According to the display on the GTS, read the Data List.

Powertrain > EV > Data List
Tester Display
BATT Voltage for Gear Shift Control Module
50003 397 567

Result:
Result Proceed to
BATT Voltage for Gear Shift Control Module is 9 V or higher. A
BATT Voltage for Gear Shift Control Module is below 9 V. B


c.

Turn the ignition switch off.



A

4.CHECK HARNESS AND CONNECTOR (PARKING LOCK MOTOR (SHIFT CONTROL ACTUATOR ASSEMBLY) - P CON MTR RELAY)

B

6.CHECK AUXILIARY BATTERY VOLTAGE
4.CHECK HARNESS AND CONNECTOR (PARKING LOCK MOTOR (SHIFT CONTROL ACTUATOR ASSEMBLY) - P CON MTR RELAY)
a.

Disconnect the G153 parking lock motor (shift control actuator assembly) connector.


b.

Remove the P CON MTR relay from the luggage room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(G153)Location & Routing

Click Connector(G153)Body>Floor Wire / No. 3 Floor Wire>Shift Control Actuator Assembly

P CON MTR relay terminal 5 - G153-7 (BMA) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(G153)Location & Routing

Click Connector(G153)Body>Floor Wire / No. 3 Floor Wire>Shift Control Actuator Assembly

P CON MTR relay terminal 5 or G153-7 (BMA) - Other terminals Always 10 kΩ or higher



d.

Install the P CON MTR relay.


e.

Reconnect the G153 parking lock motor (shift control actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

5.INSPECT P CON MTR RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT P CON MTR RELAY
a.
C453749C01
1.323,2.521 1.99,2.927 true 0.219,0.177 0.531,0.375 0.313,0.198 10 false *1 2.104,2.958 2.406,3.188 0.302,0.229 10 false *2
*1 Luggage Room Relay Block
*2 P CON MTR Relay


Remove the P CON MTR relay from the luggage room relay block.


b.
C453750C01
0.094,0.094 0.406,0.292 0.313,0.198 10 false *1
*1 P CON MTR Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω



c.

Install the P CON MTR relay.


Result:
Proceed to
OK
NG



OK

NG

REPLACE P CON MTR RELAY

6.CHECK AUXILIARY BATTERY VOLTAGE
a.

Disconnect the D93 shift control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(D93)Location & Routing

Click Connector(D93)Instrument Panel>Instrument Panel Wire>Shift Control ECU

D93-1 (BATT) - Body ground Ignition switch off 8 to 15.4 V



c.

Reconnect the D93 shift control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - P CON MAIN FUSE)
7.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - P CON MAIN FUSE)
a.

Disconnect the shift control ECU connector.


b.

Remove the P CON MAIN fuse from the luggage room relay block.

C450339C02
5.063,0.24 5.427,0.49 0.365,0.25 4.219,0.906 4.729,1.042 true 0.688,0.229 1,0.427 0.313,0.198 10 false *1 2.531,1.25 2.844,1.448 0.313,0.198 10 false *2 4.052,0.125 4.365,0.323 0.313,0.198 10 false *a 3.854,0.792 4.26,0.969 0.406,0.177 10 false BATT 5.115,0.292 5.573,0.49 0.458,0.198 10 false D93
*1 Luggage Room Relay Block *2 P CON MAIN Fuse
*a Front view of wire harness connector
(to Shift Control ECU)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(D93)Location & Routing

Click Connector(D93)Instrument Panel>Instrument Panel Wire>Shift Control ECU

P CON MAIN fuse terminal 2 - D93-1 (BATT) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

Click Location & Routing(D93)Location & Routing

Click Connector(D93)Instrument Panel>Instrument Panel Wire>Shift Control ECU

P CON MAIN fuse terminal 2 or D93-1 (BATT) - Body ground Always 10 kΩ or higher



d.

Reconnect the shift control ECU connector.


e.

Install the P CON MAIN fuse.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (P CON MAIN FUSE - AUXILIARY BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (P CON MAIN FUSE - AUXILIARY BATTERY)
a.
C450340C02
0.125,0.083 0.438,0.281 0.313,0.198 10 false *1 2.323,1.406 2.635,1.604 0.313,0.198 10 false *2
*1 Luggage Room Relay Block
*2 P CON MAIN Fuse


Remove the P CON MAIN fuse from the luggage room relay block.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Disconnect the cable from the positive (+) auxiliary battery terminal.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
P CON MAIN fuse terminal 1 - Auxiliary battery positive (+) cable Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
P CON MAIN fuse terminal 1 - Body ground Always 10 kΩ or higher



e.

Connect the cable to the positive (+) auxiliary battery terminal.


f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Install the P CON MAIN fuse.


Result:
Proceed to
OK
NG



OK

9.CHARGE AUXILIARY BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHARGE AUXILIARY BATTERY
a.

Charge the auxiliary battery.


Result:
Proceed to
NEXT



NEXT

10.CHECK OPERATION
10.CHECK OPERATION
a.

Turn the ignition switch to ON.


b.

Depress the brake pedal and move the shift lever to select neutral (N).


c.

Check that if there is an error message displayed on the multi-information display.

Result:
Result Proceed to
"Stop vehicle in a safe place Push P switch" does not displayed on the multi-information display. A
"Stop vehicle in a safe place Push P switch" displayed on the multi-information display. B



d.

Push the P position switch (parking switch) to select park (P).


e.

Turn the ignition switch off.



A

END

B