Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2020.11–2021.08
RM37H0E _53 Suspension _096766 TIRE PRESSURE MONITORING _0454878 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2126  Transmitter ID not Received in Main Mode  


DESCRIPTION

After the tire pressure warning valve and transmitter ID registration is completed using the GTS or ID registration was canceled via the automatic ID registration function, DTC C2126 is output from the tire pressure warning ECU and receiver.

After ID registration is complete using the GTS, the tire pressure warning light illuminates after blinking for 1 minute. When the tire pressure warning ECU and receiver receives the data from all tire pressure warning valve and transmitters with registered IDs, the tire pressure is judged to be normal and the tire pressure warning light turns off.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C2126 Transmitter ID not Received in Main Mode
·

Data cannot be received from all registered transmitter ID's for 1 trip after transmitter ID registration is completed

·

When the ID registration operation is canceled via the automatic ID registration function


·

Transmitter ID registration failure

·

Tire pressure warning valve and transmitter

·

Tire pressure warning ECU and receiver

·

Smart Access System with Push-button Start (for Entry Function)


Tire Pressure Monitor A

DTC Detection Conditions:
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition After the tire pressure warning valve and transmitter ID registration is completed ○ -
While ID registration is performed via the automatic ID registration function - ○
Malfunction Status Data cannot be received from all registered tire pressure warning valve and transmitter after ID registration is completed ○ -
When canceled - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


NOTICE:

If DTC C2126 is output, C2128 may be output simultaneously. In this case, first perform troubleshooting for C2128 first and then perform troubleshooting for C2126.


HINT:

The purpose of this DTC is to help prevent delivering a vehicle that has incorrectly registered transmitter IDs. After all IDs are registered, DTC C2126 is detected and the tire pressure warning light blinks for 1 minute and then illuminates. If the tire pressure warning light does not go off after a little while, the transmitter IDs may be incorrectly registered.


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, first use the GTS to record all of the current IDs and registered tires with transmitters (4 or 5 tires) of the tire pressure warning valve and transmitter registered to the tire pressure warning ECU and receiver.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.



PROCEDURE

1.CHECK VEHICLE TYPE
Result:
Result Proceed to
excluding JPD20R-CEDSSW (w/ Panic Switch) A
for JPD20R-CEDSSW (w/ Panic Switch) B



A

2.CHECK WIRELESS DOOR LOCK FUNCTION

B

8.IDENTIFY TRANSMITTER NOT RECEIVED
2.CHECK WIRELESS DOOR LOCK FUNCTION
a.

Check the wireless door lock function using the electrical key transmitter sub-assembly switch.


Result:
Result Proceed to
Operates normally A
Does not operate normally B



A

3.IDENTIFY TRANSMITTER NOT RECEIVED

B

3.IDENTIFY TRANSMITTER NOT RECEIVED

Pre-procedure1

a.

Set the tire pressure to the specified value.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION


Procedure1

b.

Check the value by referring to the following table.

Chassis > Tire Pressure Monitor > Data List
Tester Display
ID 1 Tire Inflation Pressure
ID 2 Tire Inflation Pressure
ID 3 Tire Inflation Pressure
ID 4 Tire Inflation Pressure
50003 203 36,37,38,39
Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 2 Tire Inflation Pressure ID2 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 3 Tire Inflation Pressure ID3 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 4 Tire Inflation Pressure ID4 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
HINT:
·

*: It may take a few minutes until the values are displayed.

·

The wheel position cannot be determined from ID1 through ID4 on the Data List.




c.

Decrease quickly the tire pressure of 1 wheel by 40 kPa (0.4 kgf/cm2) or more within 30 seconds, and then check the value on the Data List.

GTS Display Status Faulty Tire Pressure Warning Valve and Transmitter
The "ID Tire Inflation Pressure" data changes. Normal tire pressure warning valve and transmitter
The "ID Tire Inflation Pressure" data does not change. Tire pressure warning valve and transmitter that matches the DTC.


d.

Repeat the above procedure for each of the remaining tires, and determine the pressure warning valve and transmitter corresponding to the DTC.

NOTICE:

If the tire pressure warning valve and transmitter is normal, record the confirmed tire position and tire pressure warning valve and transmitter ID.


HINT:
·

It may take a few minutes until the values are displayed.

·

When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.




e.

Check all tire pressure warning valve and transmitters.


Result:
Result Proceed to
Change in all tire inflation pressure data A
No change in all tire inflation pressure data B
No change in any tire inflation pressure data C


Post-procedure1

f.

None



A

END

B

4.CHECK TRANSMITTER ID

C

5.CHECK TRANSMITTER ID
4.CHECK TRANSMITTER ID

Pre-procedure1

a.

Refer to the following chart and record all of the tire pressure warning valve and transmitter IDs.

Chassis > Tire Pressure Monitor > Data List
Tester Display
Registered ID 1 Code
Registered ID 2 Code
Registered ID 3 Code
Registered ID 4 Code
50003 203 7,8,9,10
Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Registered ID 1 Code Registered ID1 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID1 displayed -
Registered ID 2 Code Registered ID2 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID2 displayed -
Registered ID 3 Code Registered ID3 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID3 displayed -
Registered ID 4 Code Registered ID4 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID4 displayed -
HINT:
·

*: Displayed only when the ID No. is not registered.

·

The wheel position cannot be determined from ID1 through ID4 on the Data List.




b.

Disassemble all of the tires and check the tire pressure warning valve and transmitter IDs.

C413296C10
5.156,1.083 5.823,0.469 5.823,0.469 5.958,0.469 true 0.479,0.292 0.792,0.49 0.313,0.198 10 false *1 6.042,0.375 6.354,0.573 0.313,0.198 10 false *a
*1 Tire Pressure Warning Valve and Transmitter - -
*a Transmitter ID (7-digit Number) - -



Procedure1

c.

Confirm that the ID number on the transmitter and recorded transmitter ID match.


Result:
Result Proceed to
Match A
Do not match B


Post-procedure1

d.

None



A

B

6.REGISTRATION OF TRANSMITTER ID
5.CHECK TRANSMITTER ID

Pre-procedure1

a.

Refer to the following chart and record all of the tire pressure warning valve and transmitter IDs.

Chassis > Tire Pressure Monitor > Data List
Tester Display
Registered ID 1 Code
Registered ID 2 Code
Registered ID 3 Code
Registered ID 4 Code
50003 203 7,8,9,10
Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Registered ID 1 Code Registered ID1 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID1 displayed -
Registered ID 2 Code Registered ID2 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID2 displayed -
Registered ID 3 Code Registered ID3 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID3 displayed -
Registered ID 4 Code Registered ID4 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID4 displayed -
HINT:
·

*: Displayed only when the ID No. is not registered.

·

The wheel position cannot be determined from ID1 through ID4 on the Data List.




b.

Disassemble all of the tires and check the tire pressure warning valve and transmitter IDs.

C413296C10
5.156,1.083 5.823,0.469 5.823,0.469 5.958,0.469 true 0.479,0.292 0.792,0.49 0.313,0.198 10 false *1 6.042,0.375 6.354,0.573 0.313,0.198 10 false *a
*1 Tire Pressure Warning Valve and Transmitter - -
*a Transmitter ID (7-digit Number) - -



Procedure1

c.

Confirm that the ID number on the transmitter and recorded transmitter ID match.


Result:
Result Proceed to
Match A
Do not match B


Post-procedure1

d.

None



A

REPLACE CORRESPONDING TIRE PRESSURE WARNING VALVE AND TRANSMITTER

B

6.REGISTRATION OF TRANSMITTER ID
6.REGISTRATION OF TRANSMITTER ID
a.

Perform ID registration for the tire pressure warning valve and receiver.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION


Result:
Proceed to
NEXT



NEXT

7.PERFORM INITIALIZATION
7.PERFORM INITIALIZATION

Pre-procedure1

a.

Set the tire pressure to the specified value.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION


Procedure1

b.

Initialize the tire pressure warning system.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT


Post-procedure1

c.

None



NEXT

END

8.IDENTIFY TRANSMITTER NOT RECEIVED

Pre-procedure1

a.

Set the tire pressure to the specified value.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION


b.

Check the value by referring to the following table.

Chassis > Tire Pressure Monitor > Data List
Tester Display
ID 1 Tire Inflation Pressure
ID 2 Tire Inflation Pressure
ID 3 Tire Inflation Pressure
ID 4 Tire Inflation Pressure
50003 203 36,37,38,39
Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ID 1 Tire Inflation Pressure ID1 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 2 Tire Inflation Pressure ID2 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 3 Tire Inflation Pressure ID3 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge)/ 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
ID 4 Tire Inflation Pressure ID4 tire inflation pressure min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
Actual tire inflation pressure If N/A is displayed, data has not been received.*
HINT:
·

*: It may take a few minutes until the values are displayed.

·

The wheel position cannot be determined from ID1 through ID4 on the Data List.




Procedure1

c.

Decrease quickly the tire pressure of 1 wheel by 40 kPa (0.4 kgf/cm2) or more within 30 seconds, and then check the value on the Data List.

GTS Display Status Faulty Tire Pressure Warning Valve and Transmitter
The "ID Tire Inflation Pressure" data changes. Normal tire pressure warning valve and transmitter
The "ID Tire Inflation Pressure" data does not change. Tire pressure warning valve and transmitter that matches the DTC.


d.

Repeat the above procedure for each of the remaining tires, and determine the pressure warning valve and transmitter corresponding to the DTC.

NOTICE:

If the tire pressure warning valve and transmitter is normal, record the confirmed tire position and tire pressure warning valve and transmitter ID.


HINT:
·

It may take a few minutes until the values are displayed.

·

When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.




e.

Check all tire pressure warning valve and transmitters.


Result:
Result Proceed to
Change in all tire inflation pressure data A
No change in all tire inflation pressure data B
No change in any tire inflation pressure data C


Post-procedure1

f.

None



A

END

B

9.CHECK TRANSMITTER ID

C

5.CHECK TRANSMITTER ID
9.CHECK TRANSMITTER ID

Pre-procedure1

a.

Refer to the following chart and record all of the tire pressure warning valve and transmitter IDs.

Chassis > Tire Pressure Monitor > Data List
Tester Display
Registered ID 1 Code
Registered ID 2 Code
Registered ID 3 Code
Registered ID 4 Code
50003 203 7,8,9,10
Chassis > Tire Pressure Monitor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Registered ID 1 Code Registered ID1 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID1 displayed -
Registered ID 2 Code Registered ID2 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID2 displayed -
Registered ID 3 Code Registered ID3 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID3 displayed -
Registered ID 4 Code Registered ID4 code min.: 0
max.: FFFFFFF*
ID No. registered for transmitter ID4 displayed -
HINT:
·

*: Displayed only when the ID No. is not registered.

·

The wheel position cannot be determined from ID1 through ID4 on the Data List.




b.

Disassemble all of the tires and check the tire pressure warning valve and transmitter IDs.

C413296C10
5.156,1.083 5.823,0.469 5.823,0.469 5.958,0.469 true 0.479,0.292 0.792,0.49 0.313,0.198 10 false *1 6.042,0.375 6.354,0.573 0.313,0.198 10 false *a
*1 Tire Pressure Warning Valve and Transmitter - -
*a Transmitter ID (7-digit Number) - -



Procedure1

c.

Confirm that the ID number on the transmitter and recorded transmitter ID match.


Result:
Result Proceed to
Match A
Do not match B


Post-procedure1

d.

None



A

B

6.REGISTRATION OF TRANSMITTER ID