Perform the following troubleshooting procedure when the EPS warning light remains on after the ignition switch to ON (READY) but no DTCs are stored.
If the power steering ECU (rack and pinion power steering gear assembly) detects a malfunction in the power source voltage input (IG) circuit, the EPS warning light illuminates.
If the power steering ECU (rack and pinion power steering gear assembly) detects a drop in the power voltage input (IG and PIG) circuit, the force required to turn the steering wheel may increase, the EPS warning light turns on in order to warn the driver.
Inspect the fuses for circuits related to this system before performing the following procedure.
When replacing the rack and pinion power steering gear assembly, perform Power Steering ECU Initial Setting.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>UTILITY
Check the vehicle control history (RoB).
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>VEHICLE CONTROL HISTORY
If vehicle control history is stored, the EPS warning light may illuminate.
| Result | Proceed to |
|---|---|
| Vehicle control history of power steering system control does not exist | A |
| Vehicle control history of power steering system control exists | B |
A
B
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>VEHICLE CONTROL HISTORY
After performing inspections and repairs on the system related to the vehicle control history, clear the vehicle control history.
Jiggle the rack and pinion power steering gear assembly connectors and wire harness up and down, and left and right to check the illumination condition of the EPS warning light in the combination meter assembly.
The EPS warning light illumination condition does not change.
When the EPS warning light is operating properly, it illuminates when the ignition switch is ON and turns off when the ignition switch is ON (READY).
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Disconnect the a1 rack and pinion power steering gear assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(a1)Location & Routingewd_type=routing;type=c;code=a1 Click Connector(a1)Engine Compartment>ECU Wire Sub-Assembly>Power Steering ECU with Motor Assembly (Rack & Pinion Power Steering Gear Assembly)ewd_type=component;type=c;code=a1;pinno=7 |
||
| a1-7 (PGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A80 rack and pinion power steering gear assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A80)Location & Routingewd_type=routing;type=c;code=A80 |
||
| A80-7 (GNDB) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the a1 rack and pinion power steering gear assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(a1)Location & Routingewd_type=routing;type=c;code=a1 Click Connector(a1)Engine Compartment>ECU Wire Sub-Assembly>Power Steering ECU with Motor Assembly (Rack & Pinion Power Steering Gear Assembly)ewd_type=component;type=c;code=a1;pinno=9,8 |
||
| a1-9 (IG) - Body ground | Ignition switch ON | 8 to 16 V |
| a1-8 (PIG) - Body ground | Always | 9 to 16 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A80 rack and pinion power steering gear assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A80)Location & Routingewd_type=routing;type=c;code=A80 |
||
| A80-9 (IGB) - Body ground | Ignition switch ON | 8 to 16 V |
| A80-8 (PIGB) - Body ground | Always | 9 to 16 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the combination meter assembly.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the A79 rack and pinion power steering gear assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A79)Location & Routingewd_type=routing;type=c;code=A79 |
||
| A79-7 (PGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A79 rack and pinion power steering gear assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A79)Location & Routingewd_type=routing;type=c;code=A79 |
||
| A79-4 (IG) - Body ground | Ignition switch ON | 8 to 16 V |
| A79-8 (PIG) - Body ground | Always | 9 to 16 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the combination meter assembly.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING