*1: for Dual
*2: for 3 Zone
*3: for LHD
*4: for RHD
The No. 1 air conditioning radiator damper servo sub-assembly (MODE FACE*1, driver side MODE FACE*2)*3, No. 3 air conditioning radiator damper servo sub-assembly (MODE FACE*1, driver side MODE FACE*2)*4 sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the No. 1 air conditioning radiator damper servo sub-assembly (MODE FACE*1, driver side MODE FACE*2)*3, No. 3 air conditioning radiator damper servo sub-assembly (MODE FACE*1, driver side MODE FACE*2)*4 to the appropriate position, which controls the air outlet switching.
The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | DTC Output from | Priority |
|---|---|---|---|---|---|---|
| B1443 | Air Outlet Damper Control Servo Motor Circuit | Diagnosis condition:
During No. 1 air conditioning radiator damper servo sub-assembly (MODE FACE*1, driver side MODE FACE*2)*3, No. 3 air conditioning radiator damper servo sub-assembly (MODE FACE*1, driver side MODE FACE*2)*4 operation Malfunction status:
The damper servo operation request signal is output but the position information of the servo does not change or servo is malfunctioning Detection time:
Continuously for 30 seconds or more |
·
No. 1 air conditioning radiator damper servo sub-assembly (MODE FACE*1, driver side MODE FACE*2)*3 ·
No. 3 air conditioning radiator damper servo sub-assembly (MODE FACE*1, driver side MODE FACE*2)*4 ·
Air conditioning harness assembly ·
Air conditioning amplifier assembly |
Memorized | Air Conditioner | B |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | During No. 1 air conditioning radiator damper servo sub-assembly (MODE FACE*1, driver side MODE FACE*2)*3, No. 3 air conditioning radiator damper servo sub-assembly (MODE FACE*1, driver side MODE FACE*2)*4 operation | ○ | ○ |
| Malfunction Status | The damper servo operation request signal is output but the position information of the servo does not change | ○ | - |
| The damper servo operation request signal is output but the position information of the servo is malfunctioning | - | ○ | |
| Detection Time | Continuously for 30 seconds or more | Continuously for 30 seconds or more | |
| Trip Count | 1 trip | 1 trip | |
If the conditions match either of these patterns, a DTC will be output.
Confirm that no mechanical problem is present because this diagnostic code can be output when either a damper link or the damper is mechanically locked.
When installing the damper servo motor, make sure to install it correctly.
When the servo motor is replaced, be sure to perform servo motor initialization.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>INITIALIZATION
Confirm that no mechanical problem is present because this DTC can be output when either a damper link or damper is mechanically locked.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Check for DTCs.
| Result | Proceed to |
|---|---|
| B1443 is output | A |
| B1443 and B1497 are output | B |
A
B
Check for No. 1 air conditioning radiator damper servo sub-assembly is installed correctly.
No. 1 air conditioning radiator damper servo sub-assembly is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for a wire harness caught between the links of the motors and dampers.
No wire harnesses are caught between the links of the motors and dampers.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Remove the No. 1 air conditioning radiator damper servo sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for LHD)>DISASSEMBLY
Procedure1
Operate the dampers by hand.
The dampers are easily operated by hand.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Check for DTCs.
| Result | Proceed to |
|---|---|
| B1443 is output | A |
| B1443 and B1497 are output | B |
A
B
Check for No. 3 air conditioning radiator damper servo sub-assembly is installed correctly.
No. 3 air conditioning radiator damper servo sub-assembly is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for a wire harness caught between the links of the motors and dampers.
No wire harnesses are caught between the links of the motors and dampers.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Remove the No. 3 air conditioning radiator damper servo sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for RHD)>DISASSEMBLY
Procedure1
Operate the dampers by hand.
The dampers are easily operated by hand.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG