Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM37H0E _58 Vehicle Interior _095300 HEATING / AIR CONDITIONING _0455055 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1475  A/C Inverter Cooling / Heating System Malfunction  


DESCRIPTION

The temperature sensor of the compressor with motor assembly detects the A/C inverter temperature.

If the temperature exceeds the maximum, operation of the compressor with motor assembly will be stopped, and this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
B1475 A/C Inverter Cooling / Heating System Malfunction
·

Diagnosis condition: Ignition switch ON (READY)

·

Malfunction status: Outside base temperature in the Inverter (unreasonable temperature)

·

Detection time: None


·

Cooling fan system

·

Refrigerant volume

·

Compressor with motor assembly

·

CAN communication system


Memorized Air Conditioner B

CAUTION / NOTICE / HINT

CAUTION:
·

After removing the EV battery service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

·

After removing the EV battery service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs from these systems are output simultaneously.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

HINT:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

2.CHECK COOLING FAN SYSTEM

B

2.CHECK COOLING FAN SYSTEM
a.

Check that the cooling fan system is operated normally.

HINT:

Click hereEngine / Hybrid System>COOLING>COOLING FAN SYSTEM>ON-VEHICLE INSPECTION


OK:

Cooling fan system is operated normally.



Result:
Proceed to
OK
NG



OK

3.CHECK REFRIGERANT PRESSURE

NG

3.CHECK REFRIGERANT PRESSURE

Pre-procedure1


b.

Turn the ignition switch to ON (READY).


Procedure1

a.

Read the manifold gauge pressure when the following conditions are met.

i.

Prepare the vehicle according to the table below.

Item Condition
Door Fully closed (windows also fully closed)
A/C Switch On
Recirculation/fresh Control Switch Recirculation
Set Temperature MAX COLD
Blower Speed HI
Air Conditioning Air Inlet Temperature 25 to 35°C (77 to 95°F)



Standard Pressure:
Low pressure side:

150 to 250 kPa (1.5 to 2.5 kgf/cm2, 22 to 36 psi)

High pressure side:

1370 to 1570 kPa (14 to 16 kgf/cm2, 199 to 228 psi)


Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

4.CLEAR FOR DTC

NG

4.CLEAR FOR DTC
NOTICE:

If the engine keeps idling when ambient temperature is high, the compressor with motor assembly may automatically stop to protect the inverter circuit, and DTC B1475 may be stored.


a.

Set the vehicle condition when the DTCs are output.

i.

Set the "Inspection Mode".

HINT:

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE



ii.

Prepare the vehicle according to the table below for 30 minutes or more.

Item Condition
Blower speed HI
A/C switch On
Temperature setting MAX COLD



b.

Clear the DTCs.

Body Electrical > Air Conditioner > Clear DTCs
50002 121

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
B1475 is not output A
B1475 is output B



A

B

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY