Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM37H0E _58 Vehicle Interior _095300 HEATING / AIR CONDITIONING _0455055 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1471  A/C Inverter High Voltage Power Resource System Malfunction  


DESCRIPTION

The EV control ECU monitors the voltage of the HV battery. The EV control ECU stops compressor control and stores this DTC when the monitored voltage is outside the specified range.

This DTC will be stored as a history DTC. Compressor control may not resume unless the ignition switch is turned off.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority
B1471 A/C Inverter High Voltage Power Resource System Malfunction
Diagnosis condition:

Ignition switch ON (READY)


Malfunction status:

Open or short in A/C inverter high voltage power resource system


Detection time:

None


·

CAN communication system

·

Hybrid control system

·

No. 1 EV battery pack wire

·

Compressor with motor assembly


Memorized Air Conditioner B

WIRING DIAGRAM

E414323E05
3.51,0.781 4.125,0.979 0.615,0.198 10 false LIN3 3.219,0.615 3.833,0.813 0.615,0.198 10 false 13 3.427,1.281 4.042,1.479 0.615,0.198 10 false A17 3.448,1.458 4.552,1.667 1.104,0.208 10 false EV Control ECU 3.198,2.188 4.323,2.406 1.125,0.219 10 false from IG1 Relay 5.5,1.302 7.083,1.698 1.583,0.396 10 false Air Conditioning Amplifier Assembly 1.958,2.344 3.083,2.563 1.125,0.219 10 false R/B-IG1 NO.2 1.542,0.792 2.156,0.99 0.615,0.198 10 false B23 1.625,0.563 2.24,0.76 0.615,0.198 10 false 3 1.552,2.208 2.167,2.406 0.615,0.198 10 false B23 1.615,1.979 2.229,2.177 0.615,0.198 10 false 1 1.552,2.615 2.167,2.813 0.615,0.198 10 false D20 1.625,2.427 2.24,2.625 0.615,0.198 10 false 2 1.583,3.031 2.198,3.229 0.615,0.198 10 false b3 1.635,2.823 2.25,3.021 0.615,0.198 10 false 2 1.615,3.865 2.229,4.063 0.615,0.198 10 false b3 1.625,3.656 2.24,3.854 0.615,0.198 10 false 1 1.031,0.802 1.646,1 0.615,0.198 10 false DOUT 1.177,2.198 1.792,2.396 0.615,0.198 10 false IG1 1.104,2.625 1.719,2.823 0.615,0.198 10 false GND 1.281,3.052 1.896,3.25 0.615,0.198 10 false P 1.281,3.865 1.896,4.063 0.615,0.198 10 false N 5.135,3.719 5.75,3.917 0.615,0.198 10 false N 5.135,2.885 5.75,3.083 0.615,0.198 10 false P 0.313,4.729 1.427,5.115 1.115,0.385 10 false Compressor with Motor Assembly 2.5,4.698 4.458,4.885 1.958,0.188 10 false No. 1 EV Battery Pack Wire 4.958,4.885 7.031,5.146 2.073,0.26 10 false Inverter with Converter Assembly 4.948,4.719 6.917,4.979 1.969,0.26 10 false b4 0.76,5.406 2.99,5.604 2.229,0.198 10 false : CAN Communication Line 0.76,5.865 2.99,6.063 2.229,0.198 10 false : LIN Communication Line 0.771,6.333 3,6.531 2.229,0.198 10 false : High Voltage Line 3.229,3.542 3.844,3.74 0.615,0.198 10 false * 3.25,4.385 3.865,4.583 0.615,0.198 10 false * 2.792,5.385 3.781,5.583 0.99,0.198 10 false *: Shielded 4.938,2.885 5.552,3.083 0.615,0.198 10 false 2 4.927,3.719 5.542,3.917 0.615,0.198 10 false 1

CAUTION / NOTICE / HINT

CAUTION:
·

After removing the EV battery service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

·

After removing the EV battery service plug grip and FC converter power outlet cable (inverter with converter assembly) on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.



NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs from these systems are output simultaneously.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

HINT:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

2.CHECK FOR DTC (HYBRID CONTROL SYSTEM)

B

2.CHECK FOR DTC (HYBRID CONTROL SYSTEM)
a.

Check if hybrid control system DTCs are output.

Powertrain > EV > Trouble Codes
50001 397
OK:

EV control system DTCs are not output.



Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.CHECK NO. 1 EV BATTERY PACK WIRE

B

3.CHECK NO. 1 EV BATTERY PACK WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Remove the No. 1 EV battery pack wire.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(b3,b4)Location & Routing

Click Connector(b3)Engine Compartment>FC Cooling Water Pump Cable>Compressor with Motor Assembly

Click Connector(b4)Engine Compartment>FC Cooling Water Pump Cable>FC Converter Assembly

b3-2 (P) - b4-2 (P) Always Below 1 Ω
b3-1 (N) - b4-1 (N) Always Below 1 Ω
b3-2 (P) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

NG