Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM37H0E _58 Vehicle Interior _095316 METER / GAUGE / DISPLAY _0455143 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150819  Turn Signal/Hazard Flasher Circuit Current Above Threshold  


DESCRIPTION

When the operation signal of the turn signal switch (headlight dimmer switch assembly) is input, the combination meter assembly operates the turn signal lights on the RH and LH sides in response to switch operation. If there is a short in the turn signal light circuit, the combination meter assembly outputs B150819.

HINT:

If there is a short in a turn signal light circuit, all of the turn signal lights on the side with the short circuit will not blink.


DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority Note
B150819 Turn Signal/Hazard Flasher Circuit Current Above Threshold
Diagnosis Condition:

Auxiliary battery voltage is 7 V or more


Malfunction Status:

Short in turn signal light circuit


·

Front turn signal light assembly (w/ Adaptive High Beam System)

·

Front turn signal light LED (w/o Adaptive High Beam System)

·

Front multiplex network door ECU (w/ Blind Spot Monitor System)

·

Outer mirror retractor

·

Side turn signal light assembly

·

Rear combination light cord

·

Rear turn signal light LED


DTC stored Combination Meter A -

WIRING DIAGRAM

B608608E02
0.563,2.177 3.271,2.677 2.708,0.5 10 false Front Turn Signal Light LED*2 0.552,2 1.271,2.25 0.719,0.25 10 false A93 2.958,0.25 3.521,0.51 0.563,0.26 10 false 1*1, 2*2 2.958,1.083 3.531,1.302 0.573,0.219 10 false 2*1, 1*2 2.74,0.24 2.896,0.438 0.156,0.198 10 false B 2.708,1.104 2.865,1.302 0.156,0.198 10 false E 4.635,0.229 5.208,0.417 0.573,0.188 10 false 13 4.885,0.229 5.198,0.427 0.313,0.198 10 false LL 6.156,3.333 6.802,4.448 0.646,1.115 10 false FLASHER CIRCUIT 2.469,2.948 2.625,3.146 0.156,0.198 10 false 2 3.708,3.354 3.865,3.552 0.156,0.198 10 false 1 3.667,2.948 4.01,3.156 0.344,0.208 10 false 20 2.417,3.354 2.76,3.563 0.344,0.208 10 false 12 2.396,3.135 2.719,3.333 0.323,0.198 10 false z29 2.385,3.521 2.708,3.719 0.323,0.198 10 false z29 3.635,3.135 3.958,3.333 0.323,0.198 10 false E25 3.635,3.531 3.958,3.729 0.323,0.198 10 false E25 2.719,3.104 3.042,3.302 0.323,0.198 10 false B 2.76,3.552 3.083,3.75 0.323,0.198 10 false - 3.271,3.135 3.708,3.333 0.438,0.198 10 false TRNI 3.25,3.531 3.688,3.729 0.438,0.198 10 false GND 4.656,3.031 5,3.24 0.344,0.208 10 false 11 4.875,3.146 5.448,3.375 0.573,0.229 10 false TRNL 3.719,6.74 3.875,6.938 0.156,0.198 10 false 3 3.708,7.292 3.865,7.49 0.156,0.198 10 false 4 3.479,7.281 3.635,7.479 0.156,0.198 10 false E 3.323,6.75 3.729,6.948 0.406,0.198 10 false TRN 0.167,3.875 1.333,4.906 1.167,1.031 10 false Side Turn Signal Light Assembly LH 1.469,3.885 2.281,4.604 0.813,0.719 10 false Outer Mirror Retractor LH 2.646,4.083 4.115,4.677 1.469,0.594 10 false Front Multiplex Network Door ECU LH 0.75,7.823 1.802,8.427 1.052,0.604 10 false Rear Turn Signal Light LED 2.24,7.792 2.708,8.01 0.469,0.219 10 false G73 2.26,7.979 4.281,8.531 2.021,0.552 10 false Rear Combination Light Cord LH 4.99,7.5 5.458,7.719 0.469,0.219 10 false D42 4.979,7.698 7,8.177 2.021,0.479 10 false Combination Meter Assembly 0.167,8.479 3.229,8.677 3.063,0.198 10 false *1: w/ Adaptive High Beam System 2.5,8.49 5.563,8.688 3.063,0.198 10 false *2: w/o Adaptive High Beam System 0.188,2.604 5.698,2.844 5.51,0.24 12 false w/ Blind Spot Monitor System: 0.563,1.573 1.021,1.771 0.458,0.198 10 false A91 0.552,1.75 4.833,1.948 4.281,0.198 10 false Front Turn Signal Light Assembly LH*1 2.396,6.146 4.042,6.833 1.646,0.688 10 false Outer Mirror Retractor LH 2.396,5.99 2.854,6.188 0.458,0.198 10 false E29 0.135,4.667 5.646,4.906 5.51,0.24 12 false w/o Blind Spot Monitor System: 1.146,5.979 2.313,7.01 1.167,1.031 10 false Side Turn Signal Light Assembly LH 3.198,5.115 3.521,5.313 0.323,0.198 10 false B 3.219,5.531 3.542,5.729 0.323,0.198 10 false - 3.417,5.104 3.729,5.302 0.313,0.198 10 false 16 3.417,5.51 3.729,5.708 0.313,0.198 10 false 12

B608609E02
0.563,2.417 3.271,2.917 2.708,0.5 10 false Front Turn Signal Light LED*2 0.552,2.26 1.271,2.51 0.719,0.25 10 false A92 2.979,0.427 3.542,0.688 0.563,0.26 10 false 1*1, 2*2 2.979,1.26 3.552,1.479 0.573,0.219 10 false 2*1, 1*2 2.74,0.448 2.896,0.646 0.156,0.198 10 false B 2.719,1.271 2.875,1.469 0.156,0.198 10 false E 4.698,0.448 5.271,0.635 0.573,0.188 10 false 7 4.896,0.458 5.208,0.656 0.313,0.198 10 false LR 6.156,3.333 6.802,4.448 0.646,1.115 10 false FLASHER CIRCUIT 2.469,3.135 2.625,3.333 0.156,0.198 10 false 2 3.708,3.521 3.865,3.719 0.156,0.198 10 false 1 3.667,3.135 4.01,3.344 0.344,0.208 10 false 20 2.417,3.542 2.76,3.75 0.344,0.208 10 false 12 2.396,3.313 2.719,3.51 0.323,0.198 10 false z28 2.385,3.708 2.708,3.906 0.323,0.198 10 false z28 3.656,3.313 3.979,3.51 0.323,0.198 10 false E7 3.656,3.708 3.979,3.906 0.323,0.198 10 false E7 2.719,3.323 3.042,3.521 0.323,0.198 10 false B 2.74,3.719 3.063,3.917 0.323,0.198 10 false - 3.26,3.313 3.698,3.51 0.438,0.198 10 false TRNI 3.25,3.708 3.688,3.906 0.438,0.198 10 false GND 4.656,3.219 5,3.427 0.344,0.208 10 false 5 4.875,3.323 5.448,3.552 0.573,0.229 10 false TRNR 3.708,6.844 3.865,7.042 0.156,0.198 10 false 3 3.708,7.427 3.865,7.625 0.156,0.198 10 false 4 3.479,7.406 3.635,7.604 0.156,0.198 10 false E 3.323,6.844 3.729,7.042 0.406,0.198 10 false TRN 0.167,4.063 1.333,5.094 1.167,1.031 10 false Side Turn Signal Light Assembly RH 1.469,4.073 2.281,4.792 0.813,0.719 10 false Outer Mirror Retractor RH 2.635,4.24 4.104,4.833 1.469,0.594 10 false Front Multiplex Network Door ECU RH 0.417,7.885 2.083,8.458 1.667,0.573 10 false Rear Turn Signal Light LED 2.24,7.875 2.708,8.094 0.469,0.219 10 false G72 2.25,8.031 4.271,8.583 2.021,0.552 10 false Rear Combination Light Cord RH 4.938,8.219 5.406,8.438 0.469,0.219 10 false D42 4.938,8.375 6.958,8.854 2.021,0.479 10 false Combination Meter Assembly 0.167,8.479 3.229,8.677 3.063,0.198 10 false *1: w/ Adaptive High Beam System 2.396,8.49 5.458,8.688 3.063,0.198 10 false *2: w/o Adaptive High Beam System 0.156,2.833 5.667,3.073 5.51,0.24 12 false w/ Blind Spot Monitor System: 0.563,1.771 1.021,1.969 0.458,0.198 10 false A90 0.563,1.948 4.844,2.146 4.281,0.198 10 false Front Turn Signal Light Assembly RH*1 2.396,6.313 4.042,7 1.646,0.688 10 false Outer Mirror Retractor RH 2.396,6.135 2.854,6.333 0.458,0.198 10 false E11 0.135,4.865 5.646,5.104 5.51,0.24 12 false w/o Blind Spot Monitor System: 0.917,6.156 2.281,6.927 1.365,0.771 10 false Side Turn Signal Light Assembly RH 3.208,5.313 3.531,5.51 0.323,0.198 10 false B 3.219,5.708 3.542,5.906 0.323,0.198 10 false - 3.406,5.313 3.719,5.51 0.313,0.198 10 false 16 3.396,5.708 3.708,5.906 0.313,0.198 10 false 12

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.


Result:
Result Proceed to
Front turn signal light LH does not blink. A
Front turn signal light RH does not blink. B
Side turn signal light LH and rear turn signal light LH does not blink. C
Side turn signal light RH and rear turn signal light RH does not blink. D



A

2.CLEAR DTC

B

9.CLEAR DTC

C

16.CLEAR DTC

D

31.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

Result:
Proceed to
NEXT



NEXT

3.CHECK VEHICLE TYPE
3.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/o Adaptive High Beam System A
w/ Adaptive High Beam System B



A

4.CHECK FRONT TURN SIGNAL LIGHT LED

B

7.CHECK FRONT TURN SIGNAL LIGHT ASSEMBLY LH
4.CHECK FRONT TURN SIGNAL LIGHT LED

Pre-procedure1

a.

Disconnect the A93 front turn signal light LED connector.


Procedure1

a.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
B150819 is output A
B150718 is output B


Post-procedure1

a.

None



A

5.CLEAR DTC

B

5.CLEAR DTC
a.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

Result:
Proceed to
NEXT



NEXT

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)
6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the D42 combination meter assembly connector.


b.

Disconnect the A93 front turn signal light LED connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D42)Location & Routing

Click Connector(D42)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D42-13 (LL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK FRONT TURN SIGNAL LIGHT ASSEMBLY LH

Pre-procedure1

a.

Disconnect the A91 front turn signal light assembly LH connector.


Procedure1

a.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
B150819 is output A
B150718 is output B


Post-procedure1

a.

None



A

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

B

REPLACE FRONT TURN SIGNAL LIGHT ASSEMBLY LH

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the D42 combination meter assembly connector.


b.

Disconnect the A91 front turn signal light assembly LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D42)Location & Routing

Click Connector(D42)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D42-13 (LL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CLEAR DTC
a.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

Result:
Proceed to
NEXT



NEXT

10.CHECK VEHICLE TYPE
10.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/o Adaptive High Beam System A
w/ Adaptive High Beam System B



A

11.CHECK FRONT TURN SIGNAL LIGHT LED

B

14.CHECK FRONT TURN SIGNAL LIGHT ASSEMBLY RH
11.CHECK FRONT TURN SIGNAL LIGHT LED

Pre-procedure1

a.

Disconnect the A92 front turn signal light LED connector.


Procedure1

a.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
B150819 is output A
B150718 is output B


Post-procedure1

a.

None



A

12.CLEAR DTC

B

12.CLEAR DTC
a.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

Result:
Proceed to
NEXT



NEXT

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)
13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the D42 combination meter assembly connector.


b.

Disconnect the A92 front turn signal light LED connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D42)Location & Routing

Click Connector(D42)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D42-7 (LR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK FRONT TURN SIGNAL LIGHT ASSEMBLY RH

Pre-procedure1

a.

Disconnect the A90 front turn signal light assembly RH connector.


Procedure1

a.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
B150819 is output A
B150718 is output B


Post-procedure1

a.

None



A

15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

B

REPLACE FRONT TURN SIGNAL LIGHT ASSEMBLY RH

15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the D42 combination meter assembly connector.


b.

Disconnect the A90 front turn signal light assembly RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D42)Location & Routing

Click Connector(D42)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D42-7 (LR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CLEAR DTC
a.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

Result:
Proceed to
NEXT



NEXT

17.CHECK REAR COMBINATION LIGHT CORD LH
17.CHECK REAR COMBINATION LIGHT CORD LH

Pre-procedure1

a.

Disconnect the G73 rear combination light cord LH connector.


Procedure1

a.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
B150819 is output A
B150718 is output B


Post-procedure1

a.

None



A

18.CHECK VEHICLE TYPE

B

29.CLEAR DTC
18.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Blind Spot Monitor System A
w/o Blind Spot Monitor System B



A

19.CHECK FRONT MULTIPLEX NETWORK DOOR ECU LH

B

25.CHECK OUTER MIRROR RETRACTOR LH
19.CHECK FRONT MULTIPLEX NETWORK DOOR ECU LH

Pre-procedure1

a.

Disconnect the E25 front multiplex network door ECU LH connector.


Procedure1

a.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
B150819 is output A
B150718 is output B


Post-procedure1

a.

None



A

20.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

B

21.CLEAR DTC
20.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the D42 combination meter assembly connector.


b.

Disconnect the E25 front multiplex network door ECU LH connector.


c.

Disconnect the G73 rear combination light cord LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D42)Location & Routing

Click Connector(D42)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D42-11 (TRNL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CLEAR DTC
a.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

Result:
Proceed to
NEXT



NEXT

22.CHECK OUTER MIRROR RETRACTOR LH
22.CHECK OUTER MIRROR RETRACTOR LH

Pre-procedure1

a.

Disconnect the z29 outer mirror retractor LH connector.


Procedure1

a.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
B150819 is output A
B150718 is output B


Post-procedure1

a.

None



A

REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH

B

23.CLEAR DTC
23.CLEAR DTC
a.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

Result:
Proceed to
NEXT



NEXT

24.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY LH
24.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY LH

Pre-procedure1

a.

Removal the side turn signal light assembly LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL



Procedure1

a.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
B150819 is output A
B150718 is output B


Post-procedure1

a.

None



A

REPLACE OUTER MIRROR RETRACTOR LH

B

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

25.CHECK OUTER MIRROR RETRACTOR LH

Pre-procedure1

a.

Disconnect the E29 outer mirror retractor LH connector.


Procedure1

a.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
B150819 is output A
B150718 is output B


Post-procedure1

a.

None



A

26.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

B

27.CLEAR DTC
26.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the D42 combination meter assembly connector.


b.

Disconnect the E29 outer mirror retractor LH connector.


c.

Disconnect the G73 rear combination light cord LH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D42)Location & Routing

Click Connector(D42)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D42-11 (TRNL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.CLEAR DTC
a.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

Result:
Proceed to
NEXT



NEXT

28.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY LH
28.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY LH

Pre-procedure1

a.

Removal the side turn signal light assembly LH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL



Procedure1

a.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
B150819 is output A
B150718 is output B


Post-procedure1

a.

None



A

REPLACE OUTER MIRROR RETRACTOR LH

B

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

29.CLEAR DTC
a.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

Result:
Proceed to
NEXT



NEXT

30.CHECK REAR TURN SIGNAL LIGHT LED
30.CHECK REAR TURN SIGNAL LIGHT LED

Pre-procedure1

a.

Removal the rear turn signal light led.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY



Procedure1

a.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
B150819 is output A
B150718 is output B


Post-procedure1

a.

None



A

REPLACE REAR COMBINATION LIGHT CORD LH

B

31.CLEAR DTC
a.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

Result:
Proceed to
NEXT



NEXT

32.CHECK REAR COMBINATION LIGHT CORD RH
32.CHECK REAR COMBINATION LIGHT CORD RH

Pre-procedure1

a.

Disconnect the G72 rear combination light cord RH connector.


Procedure1

a.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
B150819 is output A
B150718 is output B


Post-procedure1

a.

None



A

33.CHECK VEHICLE TYPE

B

44.CLEAR DTC
33.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ Blind Spot Monitor System A
w/o Blind Spot Monitor System B



A

34.CHECK FRONT MULTIPLEX NETWORK DOOR ECU RH

B

40.CHECK OUTER MIRROR RETRACTOR RH
34.CHECK FRONT MULTIPLEX NETWORK DOOR ECU RH

Pre-procedure1

a.

Disconnect the E7 front multiplex network door ECU RH connector.


Procedure1

a.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
B150819 is output A
B150718 is output B


Post-procedure1

a.

None



A

35.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

B

36.CLEAR DTC
35.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the D42 combination meter assembly connector.


b.

Disconnect the E7 front multiplex network door ECU RH connector.


c.

Disconnect the G72 rear combination light cord RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D42)Location & Routing

Click Connector(D42)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D42-5 (TRNR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

36.CLEAR DTC
a.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

Result:
Proceed to
NEXT



NEXT

37.CHECK OUTER MIRROR RETRACTOR RH
37.CHECK OUTER MIRROR RETRACTOR RH

Pre-procedure1

a.

Disconnect the z28 outer mirror retractor RH connector.


Procedure1

a.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
B150819 is output A
B150718 is output B


Post-procedure1

a.

None



A

REPLACE FRONT MULTIPLEX NETWORK DOOR ECU RH

B

38.CLEAR DTC
38.CLEAR DTC
a.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

Result:
Proceed to
NEXT



NEXT

39.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY RH
39.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY RH

Pre-procedure1

a.

Removal the side turn signal light assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL



Procedure1

a.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
B150819 is output A
B150718 is output B


Post-procedure1

a.

None



A

REPLACE OUTER MIRROR RETRACTOR RH

B

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY RH

40.CHECK OUTER MIRROR RETRACTOR RH

Pre-procedure1

a.

Disconnect the E11 outer mirror retractor RH connector.


Procedure1

a.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
B150819 is output A
B150718 is output B


Post-procedure1

a.

None



A

41.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

B

42.CLEAR DTC
41.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

Pre-procedure1

a.

Disconnect the D42 combination meter assembly connector.


b.

Disconnect the E11 outer mirror retractor RH connector.


c.

Disconnect the G72 rear combination light cord RH connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(D42)Location & Routing

Click Connector(D42)Instrument Panel>Instrument Panel Wire>Combination Meter Assembly

D42-5 (TRNR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

a.

None



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

42.CLEAR DTC
a.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

Result:
Proceed to
NEXT



NEXT

43.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY RH
43.CHECK SIDE TURN SIGNAL LIGHT ASSEMBLY RH

Pre-procedure1

a.

Removal the side turn signal light assembly RH.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL



Procedure1

a.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
B150819 is output A
B150718 is output B


Post-procedure1

a.

None



A

REPLACE OUTER MIRROR RETRACTOR RH

B

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY RH

44.CLEAR DTC
a.

Clear the DTC.

Body Electrical > Combination Meter > Clear DTCs
50002 409

Result:
Proceed to
NEXT



NEXT

45.CHECK REAR TURN SIGNAL LIGHT LED
45.CHECK REAR TURN SIGNAL LIGHT LED

Pre-procedure1

a.

Removal the rear turn signal light led.

HINT:

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY



Procedure1

a.

Check for DTC.

Body Electrical > Combination Meter > Trouble Codes
50001 409

Result:
Result Proceed to
B150819 is output A
B150718 is output B


Post-procedure1

a.

None



A

REPLACE REAR COMBINATION LIGHT CORD RH

B