CLEARANCE WARNING ECU ASSEMBLY
Disconnect the G20 clearance warning ECU assembly connector.
Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| G20-1 (IG) - G20-31 (E) | IG power source signal | Ignition switch off | Below 1 V |
| Ignition switch to ON | 11 to 14 V | ||
| G20-31 (E) - Body ground | Ground | Always | Below 1 Ω |
Reconnect the G20 clearance warning ECU assembly connector.
Measure the voltage, resistance and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| G20-2 (BOF) - G20-31 (E) | Power source for front sensor circuit | ·
Ignition switch ON ·
Parking support brake system on |
11 to 14 V |
| G20-3 (E5) - G20-31 (E) | Ground for front clearance sonar | Always | Below 1 Ω |
| G20-4 (SOF) - G20-31 (E) | Front sensor communication signal (Front clearance sonar sensor) | ·
Ignition switch ON ·
Parking support brake system on ·
Shift position in any position other than P or R ·
Vehicle speed is less than approximately 10 km/h (6 mph) |
Pulse generation
(Refer to waveform 1) |
| G20-9 (CBZ) - G20-8 (EF) | No. 1 clearance warning buzzer signal | Buzzer sounding | Pulse generation
(Refer to waveform 2) |
| G20-26 (BBZ) - G20-25 (ER) | No. 2 clearance warning buzzer signal | Buzzer sounding | Pulse generation
(Refer to waveform 2) |
| G20-19 (BOR) - G20-31 (E) | Power source for rear sensor circuit | ·
Ignition switch ON ·
Parking support brake system on |
11 to 14 V |
| G20-20 (E1) - G20-31 (E) | Ground for rear clearance sonar | Always | Below 1 Ω |
| G20-21 (SOR) - G20-31 (E) | Rear sensor communication signal (Rear clearance sonar sensor) | ·
Ignition switch ON ·
Parking support brake system on ·
Shift position in R |
Pulse generation
(Refer to waveform ) |
Using an oscilloscope, check waveform 1.
Waveform 1 (Reference)
| Item | Content |
|---|---|
| Measurement terminal | G20-4 (SOF) - G20-31 (E) |
| Measurement setting | 5 V/DIV., 100 μs./DIV. |
| Condition | ·
Ignition switch ON ·
Parking support brake system on ·
Shift position in any position other than P or R ·
Vehicle speed less than approximately 10 km/h (6 mph) |
Using an oscilloscope, check waveform 2.
Waveform 2 (Reference)
| Item | Content |
|---|---|
| Measurement terminal | G20-9 (CBZ) - G20-8 (EF)
G20-26 (BBZ) - G20-25 (ER) |
| Measurement setting | 2 V/DIV., 500 μs./DIV. |
| Condition | Buzzer sounding |
The amplitude of the waveform changes according to the set volume.
Using an oscilloscope, check waveform 3.
Waveform 3 (Reference)
| Item | Content |
|---|---|
| Measurement terminal | G20-21 (SOR) - G20-31 (E) |
| Measurement setting | 5 V/DIV., 100 μs./DIV. |
| Condition | ·
Ignition switch ON ·
Parking support brake system on ·
Shift position in R |
EV CONTROL ECU
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>TERMINALS OF ECU
COMBINATION METER ASSEMBLY
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU
BLIND SPOT MONITOR SENSOR
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU
REAR TELEVISION CAMERA ASSEMBLY
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>TERMINALS OF ECU