Home › General › MAINTENANCE › FRONT BRAKE FLEXIBLE HOSE
RM37H0E _V1 General _095083 MAINTENANCE _0455455 FRONT BRAKE FLEXIBLE HOSE A

MAINTENANCE  FRONT BRAKE FLEXIBLE HOSE  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C437775N01
6.542,0.188 6.865,0.188 true 6.563,0.594 6.813,0.594 true 6.563,0.99 6.875,0.99 true 5.458,2.469 5.625,2.271 5.625,2.271 5.802,2.271 true 6.344,0.063 6.667,0.333 0.323,0.271 18 false 1 6.375,0.448 6.677,0.75 0.302,0.302 18 false 2 5.896,2.104 6.167,2.417 0.271,0.313 18 false 3 6.375,0.865 6.667,1.135 0.292,0.271 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) -
2 DISABLE BRAKE CONTROL - (Click here) - -
3 REMOVE FRONT WHEEL - - - -
4 DRAIN BRAKE FLUID - - (Click here) -

C450102N01
4.833,1.833 4.667,1.833 4.667,1.833 4.594,2.063 true 5.781,0.719 5.615,0.719 5.615,0.719 5.542,0.948 true 6.5,1.104 6.333,1.104 6.333,1.104 6.26,1.333 true 3.333,0.583 3.667,0.583 true 2.854,3.458 1.667,4.927 1.667,4.927 1.5,4.927 true 1.302,4.813 1.583,5.167 0.281,0.354 18 false 5 4.917,1.771 5.188,1.99 0.271,0.219 10 false ● 5.854,0.646 6.354,0.896 0.5,0.25 10 false ●*1 6.573,1.031 6.99,1.323 0.417,0.292 10 false ●*2 3.76,0.5 4.094,0.75 0.333,0.25 10 false *3

Procedure Part Name Code
Z101186

Z101188

Z101187

5 REMOVE FRONT FLEXIBLE HOSE 47313J (Click here) - -

*1 UNION BOLT *2 GASKET
*3 BRAKE TUBE - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front brake flexible hose removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

NOTICE:
·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.

·

If both left and right front flexible hoses are disconnected at the same time, be sure to place an identification mark on each hose to indicate its installation position.



HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for the RH and LH sides, except where indicated.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISABLE BRAKE CONTROL

Z101186

Click here(Click here)

Hide 3.REMOVE FRONT WHEEL

Hide 4.DRAIN BRAKE FLUID

Z101186

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.



Hide 47313J 5.REMOVE FRONT FLEXIBLE HOSE

a.
C450103N01
0.167,0.167 0.417,0.448 0.25,0.281 18 false i 3.75,0.167 4,0.448 0.25,0.281 18 false ii 2.021,3.125 2.552,3.438 0.531,0.313 18 true iii, iv

i.

Remove the union bolt and gasket, and disconnect the front flexible hose from the front disc brake cylinder assembly.


ii.

Remove the bolt and separate the front flexible hose from the front shock absorber assembly.


iii.

Using a union nut wrench, disconnect the brake line while holding the front flexible hose with a wrench.

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.




iv.

Remove the clip and front flexible hose from the vehicle body.