Home › General › MAINTENANCE › REAR DISC BRAKE PAD
RM37H0E _V1 General _095083 MAINTENANCE _0455454 REAR DISC BRAKE PAD A

MAINTENANCE  REAR DISC BRAKE PAD  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C450043N05
6.438,0.188 6.854,0.188 false 6.458,0.604 6.813,0.604 false 4.667,1.24 4.792,1.01 4.792,1.01 4.958,1.01 true 6.479,1.052 6.833,1.052 false 6.229,0.042 6.479,0.344 0.25,0.302 18 false 1 5.052,0.875 5.385,1.229 0.333,0.354 18 false 3 6.24,0.469 6.563,0.771 0.323,0.302 18 false 2 6.229,0.906 6.521,1.198 0.292,0.292 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISABLE BRAKE CONTROL - - - (Click here)
3 REAR WHEEL - - - -
4 DRAIN BRAKE FLUID - - (Click here) -

C451998N02
3.479,4.167 5.25,5.417 1.771,1.25 0.167,2.667 1.917,4.333 1.75,1.667 2,3.656 3.365,5.406 1.365,1.75 1.323,1.083 4.073,2.479 2.75,1.396 2.406,4.917 2.406,4.135 false 2.25,4.917 2.854,4.917 2.854,4.917 2.854,4.5 true 4.125,4.51 3.875,4.51 false 4.833,5 4.635,5 true 1.135,3.646 1.385,3.646 true 0.417,3.135 0.667,3.135 true 3.083,2.25 3.083,1.667 3.083,1.667 2.844,1.667 true 2.583,2.083 3.083,2.083 true 1.615,1.542 1.865,1.542 true 3.396,1.563 3.5,1.333 3.5,1.333 3.583,1.333 true 3.5,3 2.333,3 2.333,3 2.333,3.063 true 3.042,3.427 3.042,3 true 4.5,3.75 4.333,3.75 4.333,3.75 4.333,4.167 false 1.146,4.333 1.146,4.635 1.146,4.635 0.979,4.635 false 1.833,4.917 2,4.917 true 1.146,1.385 1.313,1.385 true 4.208,4.438 4.521,4.635 0.313,0.198 10 false *1 0.927,3.594 1.188,3.792 0.26,0.198 10 false *1 0.219,3.063 0.49,3.302 0.271,0.24 10 false *2 4.885,4.927 5.104,5.125 0.219,0.198 10 false *2 1.406,1.469 1.698,1.75 0.292,0.281 10 false *3 3,2.302 3.292,2.583 0.292,0.281 10 false *4 3.667,1.24 3.958,1.521 0.292,0.281 10 false *5 3.594,2.927 3.885,3.208 0.292,0.281 10 false *6 1.594,4.76 1.896,5.073 0.302,0.313 18 false 6 4.563,3.604 4.875,3.938 0.313,0.333 18 false 7 0.76,4.51 1.073,4.844 0.313,0.333 18 false 7 2.042,4.844 2.333,5.125 0.292,0.281 10 false *7 0.917,1.24 1.229,1.573 0.313,0.333 18 false 5

Procedure Part Name Code
Z101186

Z101188

Z101187

5 REAR DISC BRAKE FITTING KIT 04948 - - -
6 REAR DISC BRAKE PAD KIT 04466 (Click here) - -
7 REAR DISC BRAKE ANTI-SQUEAL SHIM 04946 - - -

*1 NO. 1 ANTI-SQUEAL SHIM *2 NO. 2 ANTI-SQUEAL SHIM
*3 PIN HOLD CLIP *4 HOLE PIN
*5 NO. 1 ANTI-RATTLE SPRING *6 INNER ANTI-RATTLE SPRING
*7 REAR DISC BRAKE PAD - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear disc brake pad removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When removing or installing the rear disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -


·

Use the same procedure for the RH and LH sides, except where indicated.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

Z101186

Click here(Click here)
NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISABLE BRAKE CONTROL

Z101186

Click here(Click here)

Hide 3.REMOVE REAR WHEEL

Hide 4.DRAIN BRAKE FLUID

Z101186

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.



Hide 04948 5.REMOVE REAR DISC BRAKE FITTING KIT

a.
C452183N01
0.583,0.448 0.74,0.646 0.156,0.198 10 false B 4.396,0.521 4.552,0.719 0.156,0.198 10 false B 0.573,1.146 0.729,1.344 0.156,0.198 10 false B 4.396,1.156 4.552,1.354 0.156,0.198 10 false B 0.479,0.792 0.635,0.99 0.156,0.198 10 false A 6,0.823 6.156,1.021 0.156,0.198 10 true A 0.115,0.083 0.406,0.5 0.292,0.417 18 false i 3.771,0.104 4.063,0.521 0.292,0.417 18 false ii

i.

While pressing the area labeled A, push the hole pin labeled B toward the rear disc brake cylinder assembly LH, and remove the pin hold clip.


ii.

While pressing the area labeled A, remove the No.1 anti-rattle spring and 2 hole pins.



Hide 04466 6.REMOVE REAR DISC BRAKE PAD KIT

Z101186

NOTICE:

Be sure to inspect the rear disc when replacing the rear disc brake pads with new ones.

Click here(Click here)



a.
C452184


Hide 04946 7.REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM

a.
C450046C01
4.75,1.781 4.75,1.5 4.75,1.5 4.917,1.5 true 3.083,2 3.083,1.448 true 2.833,2 4,2 4,2 4,1.771 true 5.458,2.115 5.458,1.833 5.458,1.833 5.667,1.833 true 2.417,1 2.417,1.25 2.417,1.25 2.25,1.25 true 1.667,0.667 1.667,0.917 1.667,0.917 1.5,0.917 true 4.333,0.25 3.25,0.25 3.25,0.25 3.25,0.354 true 3.99,0.719 3.99,0.25 true 2.635,1.938 2.896,2.135 0.26,0.198 10 false *1 2.042,1.177 2.271,1.365 0.229,0.188 10 false *2 5.74,1.76 5.979,1.958 0.24,0.198 10 false *3 4.406,0.167 4.74,0.375 0.333,0.208 10 false *4 4.99,1.438 5.24,1.677 0.25,0.24 10 false *2 1.302,0.854 1.542,1.052 0.24,0.198 10 false *3
*1 Rear Disc Brake Pad *2 No. 1 Anti-Squeal Shim
*3 No. 2 Anti-Squeal Shim *4 Inner Anti-Rattle Spring